Kachasị V Series
Otu ike inye
Access Power Controllers (Fused)

Kachasị V Series Otu ike nweta ikike njikwa ike

Models Include: Maximal3V
- 12VDC @ 5A ma ọ bụ 24VDC @ 5.4A.
– Sixteen (16) fuse-protected outputs.
Kachasị 5V
- 12VDC @ 9A.
– Sixteen (16) fuse-protected outputs..
Kachasị 7V
- 24VDC @ 9.4A.
– Sixteen (16) fuse-protected outputs.
Ntuziaka nwụnye

Maximal V Series Overview:

Altronix Maximal Access Power/Controllers distribute and switch power to access control systems and accessories. They convert a 220VAC (working range 198VAC – 256VAC), 50/60Hz input into sixteen (16) independently controlled 12VDC or 24VDC fuse-protected outputs. These Fail-Safe/Fail-Secure power outputs may be converted to dry-form “C” contacts. The outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Keypad, Push Button, REX PIR, etc. Units will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc. The FACP Interface enables Emergency Egress, and Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually selectable for any or all of the sixteen (16) outputs.

Maximal V Series Configuration Chart:

Altronix Nọmba nlereanya	Mpụta Board Na-enye Ike Voltage Nhọrọ	Ihe echekwabara fuse	Ngosipụta ihe n'otu n'otu	220VAC 50 / 60Hz Tinye ihe osise ugbu a	Ngosipụta Fuse Board na-enye ike
Kachasị 3V	12VDC @ 5A ma ọ bụ 24VDC @ 5.4A	16	3.5A	1.5A	5A/250V
Kachasị 5V	12VDC @ 9A			2.2A
Kachasị 7V	24VDC @ 9.4A			3A	6.3A/250V

Maximal V Series Features:

• Sixteen (16) independently trigger controlled outputs. Output options: a) Sixteen (16) Fail-Safe filtered and electronically regulated power outputs. b) Sixteen (16) Fail-Secure filtered and electronically regulated power outputs. c) Sixteen (16) form “C” relay outputs (rated @ 5A/28VDC or VAC). d) Any combination of the above.
• Sixteen (16) Access Control System trigger inputs. Input trigger options: a) Sixteen (16) normally open (NO) dry trigger inputs. b) Sixteen (16) open collector inputs. c) Any combination of the above.
• Iri na isii (16) nzacha na nzacha eletrọnịkị aux. mmepụta ike (a na-edepụta mmepụta @ 2.5A).
• Igwe ọkụ na-acha uhie uhie na bọọdụ ACM8 na-egosi na a na-ebute nsonaazụ onye ọ bụla (gbanye ọkụ).
• Fire Alarm disconnect (latching or non-latching) is individually selectable for any or all of the sixteen (16) outputs. Fire Alarm disconnect input trigger options: a) Normally open (NO) or normally closed (NC) dry trigger input. b) Polarity reversal input from the FACP signaling circuit.
• Green LED na bọọdụ ACM8 na-egosi nkwupu FACP kpalitere.
• Mgbasa ozi FACP na-egosi na etinyere FACP.
• The power supply input is factory installed. It provides common power for both ACM8 boards and all connected access control devices.
• ACM8 isi fuses bụ akara @ 10A. A na-atụle fiusi mmepụta @ 3.5A.
• Built-in charger for sealed lead acid or gel-type batteries. – Maximum charge current is 0.7A for AL600XB220 and AL1012XB220 power supply boards. – Maximum charge current is 3.6A for AL1024XB2V power supply board.
• Gbanwee akpaaka ka batrị nọrọ na-echere mgbe AC ​​dara.
• Zero voltage dobe mgbe unit gafere na ndabere batrị (ọnọdụ ọdịda AC).
• Mkpirisi sekit na nchekwa oke ọkụ yana nrụpụta akpaaka.
• Ntinye aka Green AC na ihe ngosi ọkụ DC na-acha uhie uhie na bọọdụ ọkọnọ ike.
• AC dara nleba anya (ụdị kọntaktị “C” nwere akara @ 1A/28VDC).
• Batrị dara na nlekọta ọnụnọ batrị (ụdị kọntaktị “C” nwere akara @ 1A/28VDC).
• Ihe mkpuchi ahụ na-anabata ihe ruru batrị anọ (4) 12VDC/12AH. Akụkụ mkpuchi (H x W x D): 26" x 19" x 6.25" (660.4mm x 482.6mm x 158.8mm).

Maximal V Installation Instructions:

Ụzọ wiwi ga-adị n'ụzọ kwekọrọ na National Electric Code/NFPA 70/ANSI, yana koodu mpaghara na ndị ọchịchị niile nwere ikike. Ezubere ngwaahịa a maka naanị ime ụlọ.

Nchọpụta Ọkụ Ọkụ Na-enye Ike LED Diagnostics	(pg. 6)
Ịnweta ihe nleba anya nke ọkụ ọkụ LED	(pg. 6)
Ngosipụta njedebe Board Supply Board	(pg. 6)
Nweta njirimara njedebe onye njikwa ike	(pg. 6)
Nkọwapụta batrị na-akwado bọọdụ na-eweta ike	(pg. 7)
Mpụta Board Na-enye Ike Voltage Ntọala	(pg. 7)
Nweta eserese ngwa ngwa njikwa ike	(pg. 8)
Eserese njikọ FACP	( peeji nke 13-14 )

1. Wụnye otu n'ime ebe achọrọ. Kaa akara na prerill oghere na mgbidi ka kwụ n'ahịrị n'ahịrị igodo atọ dị n'elu n'ogige ahụ. Wụnye ihe nkwụnye elu atọ na kposara na mgbidi na isi ihe nkedo na-apụta. Tinye oghere igodo elu nke ogige ahụ n'elu skru atọ dị elu, dị larịị na nchekwa. Kaa akara ọnọdụ nke oghere atọ dị ala. Wepu ihe mkpuchi ahụ. Gwuo oghere ndị dị ala ma wụnye ngwa ngwa atọ. Tinye oghere igodo elu nke ogige n'elu skru atọ dị elu. Wụnye skru atọ dị ala ma jide n'aka na ị ga-eme ka skru niile sie ike ( Akụkụ mkpuchi, pg. 16).
2. Connect unswitched AC power (220VAC 50/60Hz) to the terminals marked [L, N] on the power supply board. Green branch wire connects to earth (safety) ground lug. Use 14 AWG or larger for all power connections. Keep power-limited wiring separate from non-power-limited wiring.
   Opekempe 0.25" oghere ga-enyerịrị (Figs. 5-7, pgs. 10-12).
   Ịkpachara anya: Emetụla akụkụ ọla ndị ekpughere ekpughere aka. Mechie ike sekit alaka ụlọ ọrụ tupu ịwụnye ma ọ bụ na-arụ ọrụ. Enweghị akụkụ ndị ọrụ ga-arụ ọrụ n'ime. Tụtụ aka na nrụnye na ọrụ nye ndị ọrụ ruru eru.
3. Họrọ mmepụta DC chọrọ voltage by setting SW1 to the appropriate position on the Maximal3V power supply, (Figs. 1 and 1a, pg. 7). Maximal5V power supply is factory set at 12VDC and Maximal7V power supply is factory set at 24VDC.
4. Tule mmepụta voltage nke unit tupu ijikọ ngwaọrụ ọ bụla iji hụ na arụ ọrụ kwesịrị ekwesị. Na-ezighi ezi ma ọ bụ elu voltage ga-emebi ngwaọrụ ndị a.
5. Nhọrọ mmepụta (Fig 2, pg 7): Ngalaba ahụ ga-enye ma ọ bụ iri na isii (16) ọkụ ọkụ ọkụ ọkụ, iri na isii (16) ụdị akọrọ "C" mmepụta, ma ọ bụ ihe ọ bụla nchikota nke ma gbanwee ike na ụdị "C".
   (a) Mwepụta ike gbanwere nke ọdịda-Enweghị Nchekwa: Maka ịrụ ọrụ nchekwa adịghị ike jikọọ ntinye dị mma (+) nke ngwaọrụ njikwa ohere na ọdụ akara akara.
   [NC]. Jikọọ ntinye na-adịghị mma (-) nke ngwaọrụ njikwa ohere na njedebe akara [COM].
   (b) Fail-Secure Switched Power outputs: For Fail-Secure operation connect the positive (+) input of the access control devices to the terminal marked [NO]. Connect the negative (–) input of the access control devices to the terminal marked [COM].
   (c) Form “C” outputs: When form “C” outputs are desired the corresponding output fuses (1-8) of each ACM8 board must be removed.
6. Ntinye ike inyeaka (anaghị agbanwe): Jikọọ ngwaọrụ njikwa ohere nke chọrọ ike mgbe niile na njedebe akara [C] nti (+) na [COM] adịghị mma (-).
7.  Input trigger options (Fig. 2, pg. 7): (a) Normally Open [NO] input trigger:
   Ntinye 1-8 na-arụ ọrụ site na ntinye sink na-emeghe ma ọ bụ nke mepere emepe. Jikọọ ntinye njikwa njikwa ohere, ahụigodo, bọtịnụ ntinye, REX PIRs, wdg na njedebe akara [IN] na [GND].
   (b) Mepee ihe ntinye Sink Collector: Jikọọ ogwe njikwa ohere mepere emepe onye na-anakọta sink nke ọma (+) na njedebe akara [IN] yana nke ọjọọ (-) na njedebe akara [GND].
8. Fire Alarm Interface options (Figs. 8-12, pgs. 13-14): A normally closed [NC] or normally open [NO] input trigger from a fire alarm control panel or a polarity reversal input from an FACP signaling circuit will affect selected outputs. To enable FACP Disconnect for an output turn the corresponding switch(es) [SW1-SW8] OFF on each ACM8 board. To disable FACP disconnect for an output turn the corresponding switch(es) [SW1-SW8] ON on each ACM8 board.
   (a) Normally Open [NO] input:  For non-latching hook-up refer to Fig. 9, pg. 13. For latching hook-up refer to Fig. 10, pg. 13.
   (b) Normally Closed [NC] input: For non-latching hook-up refer to Fig. 11, pg. 14. For latching hook-up refer to Fig. 12, pg. 14.
   (c) FACP Signaling Circuit input trigger: Connect the positive (+) and negative (–) from the FACP signaling circuit output to the terminals marked [+ INP –]. Connect the FACP EOL to the terminals marked [+ RET –] (polarity is referenced in an alarm condition). The jumper located next to TRG LED must be cut (Fig. 2a, pg. 7, Fig. 8, pg. 13).
9. FACP Dry form “C” output (Fig. 2b, pg. 7): FACP form “C” contacts can be used to trigger reporting or signaling devices.
   These contact switches upon a fire alarm input trigger to the ACM8 boards.
10. Stand-by Battery Connections (Figs. 3-7, pgs. 8-12): For Access Control applications batteries are optional. If batteries are not used a loss of AC will result in the loss of output voltage. Batrị ga-abụrịrị ụzọ acid ma ọ bụ gel ụdị. Jikọọ otu (1) 12VDC batrị na njedebe akara [+ BAT -] maka ọrụ 12VDC (Fig 3a, pg. 8). Jiri batrị abụọ (2) 12VDC etinyere n'usoro maka ọrụ 24VDC.
11. Battery and AC Supervision outputs (Figs. 3-4, pgs. 8-9): It is required to connect supervisory trouble reporting devices to outputs marked [AC Fail, BAT FAIL] supervisory relay outputs marked [NC, C, NO] to appropriate visual notification devices.
    Jiri 22 AWG ruo 18 AWG maka ọdịda AC yana obere mkpesa batrị.
12. Ntinye nke tamper mgba ọkụ (anaghị etinye ya) (Fig. 3b-4a, pg. 8-9):
    Ugwu UL Edepụtara tamper mgba ọkụ (Honeywell Model 112 ma ọ bụ dakọtara) n'elu nke ogige. Gbanye tamper mgbanaka nkwado n'elu nsọtụ nke ihe mkpuchi ahụ dịka 2" site n'akụkụ aka nri (Figs. 3b na 4a, pgs. 8-9). Jikọọ tampgbanwee wiring gaa na ntinye Ogwe njikwa nnweta ma ọ bụ ngwaọrụ mkpesa UL Edepụtara kwesịrị ekwesị. Iji mee ka mgbaama mkpu rụọ ọrụ, mepee ọnụ ụzọ nke ogige ahụ.

Nlekọta:

A ga-anwale nkeji opekata mpe otu ugboro n'afọ maka ịrụ ọrụ kwesịrị ekwesị dịka ndị a:

Nlekọta FACP: Iji hụ na njikọ kwesịrị ekwesị na ịrụ ọrụ nke nkwụnye nkwụnye ọkụ ọkụ, biko soro usoro kwesịrị ekwesị n'okpuru:
Ntinye na-emepe emepe: Ịtụnye obere oge n'etiti ọnụ ụzọ akara [T] na [+ INP] ga-akpalite nkwụsị ọkụ ọkụ. Wepu mkpụmkpụ ka ịtọgharịa.
Ntinye na-emechikarị: Iwepu waya site na ọdụ akara akara [INP –] ga-akpalite nkwupu mkpu ọkụ. Dochie waya na ọnụ nke akara [INP –] ka ịtọgharịa.
Ntinye sekit mgbama FACP: It is necessary to trigger the Fire Alarm System. In all of the above scenarios, the green TRG LED of the ACM8s will illuminate. All outputs selected for Fire Alarm Disconnect will activate releasing locking devices. Note: All outputs [OUT 1 – OUT 8] must be in a normal (de-energized) condition prior to testing. When the unit is configured for Normally Open (Fig. 10, pg. 13) or Normally Closed (Fig. 12, pg. 14) latching operation it is necessary to reset the Fire Alarm Disconnect by activating the Normally Closed reset switch.
Mmepụta Voltage nwale: N'okpuru ọnọdụ ibu nkịtị, mmepụta DC voltage kwesịrị ịlele nke ọma voltage larịị (Nkọwapụta nkọwa batrị na-akwado bọọdụ na-eweta ike, pg. 7).
Nnwale batrị: N'okpuru ọnọdụ ibu nkịtị lelee na chajịrị batrị zuru oke, lelee voltage at the battery terminals and at the board terminals marked [+ BAT –] to ensure that there is no break in the battery connection wires. Note: AL600XB220 and AL1012XB220 Power Supply Board maximum charge current is 0.7A. AL1024XB2V Power Supply Board maximum charge current is 3.6A. The expected battery life is 5 years, however, it is recommended to change batteries within 4 years or less if necessary.

Nchọpụta Ọkụ Ọkụ Na-eweta Ike LED Diagnostics:

Ikanam		Ọkwa inye ike
Uhie (DC)	Green (AC)
ON	ON	Ọnọdụ ọrụ nkịtị.
ON	Gbanyụọ	Mfu nke AC. Ike inye batrị guzoro ọtọ.
Gbanyụọ	ON	Enweghị mmepụta DC. Mkpirisi sekit ma ọ bụ ọnọdụ ebufe ọkụ.
Gbanyụọ	Gbanyụọ	Enweghị mmepụta DC. Mfu nke AC. Achụpụrụ batrị.

Uhie (Bat)	Ọnọdụ batrị
ON	Ọnọdụ ọrụ nkịtị.
Gbanyụọ	Batrị ada ada/obere batrị.

Nchọpụta Ọkụkụ nke Onye njikwa ike nweta:

Ikanam	ON	Gbanyụọ
LED 1-Ikanam 8 (Uhie)	Mbupute relay (s) na-enye ike.	Mgbasa ozi (s) arụpụtaghị ike.
Trg (Green)	Ntinye FACP kpalitere (ọnọdụ mkpu).	FACP nkịtị (ọnọdụ enweghị mkpu).

Ngosipụta ngwụcha Board Supply Power:

Akụkọ Mgbe Ebighị Ebi	Ọrụ/Nkọwa
L, G, N	Jikọọ 220VAC 50/60Hz na njedebe ndị a: L na-ekpo ọkụ, N na-anọpụ iche.
+ DC -	Maximal3V – 12VDC @ 5A or 24VDC @ 5.4A to ACM8 boards. Maximal5V – 12VDC @ 9A to ACM8 boards. Maximal7V – 24VDC @ 9.4A to ACM8 boards.
AC FAIL NC, C, NO	Na-egosi mfu nke ike AC. Relay na-enwekarị ike mgbe ike AC dị. Ogo kọntaktị 1A @ 28VDC. A na-akọpụta ọdịda AC ma ọ bụ brownout n'ime nkeji 1 nke mmemme.
BAT FAIL NC, C, NO	Indicates low battery condition, e.g. connect to access control panel. Relay normally energized when DC power is present. Contact rating 1A @ 28VDC. A removed battery is reported within 5 minutes. Battery reconnection is reported within 1 minute. Low battery threshold: 12VDC output threshold set @ approximately 10.5VDC. 24VDC output threshold set @ approximately 21VDC.
+ BAT -	Njikọ batrị kwụrụ ọtọ. Jikọọ otu (1) 12VDC batrị na njedebe akara [+ BAT -] maka ọrụ 12VDC (Fig 3 na 3a, pg. 8). Use two (2) 12VDC batteries wired in series for 24VDC operation (Fig 4, pg. 9).

Nweta njirimara njedebe onye njikwa ike:

Akụkọ Mgbe Ebighị Ebi	Ọrụ/Nkọwa
– Ike +	Ntinye 12VDC ma ọ bụ 24VDC sitere na bọọdụ ọkọnọ ike.
– Njikwa +	Ọ metụtaghị.
NDỊ MMADỤ 1- NTỤTA 8 IN, GND	Site na ntinye na-emepe emepe na/ma ọ bụ meghere ihe ntinye ihe na-emepe onye na-anakọta ihe (rịọ ka ịpụpụ bọtịnụ, ọpụpụ pir, wdg).
OUTPUT 1- OUTPUT 8 NC, C, NO, COM	12VDC to 24VDC trigger controlled outputs: Fail-Safe [NC positive (+) & COM Negative (–)], Fail-Secure [NO positive (+) & COM Negative (–)], Auxiliary output [C positive (+) & COM Negative (–)] (When using AC power supplies polarity needs not to be observed), NC, C, NO convert to dry form “C” 5A 24VAC/VDC rated dry outputs when fuses are removed. Contacts shown in a non-triggered state.
FACP INTERFACE T, + INPUT –	Ọkụ mkpu Interface na-akpalite ntinye sitere na FACP. Ntinye ntinye nwere ike imeghe nke ọma, na-emechikarị ya site na mmepụta sekit mgbama FACP (Fig. 8-12, pg. 13-14).
FACP INTERFACE NC, C, NO	Ụdị kọntaktị relay “C” nwere akara @ 1A/28VDC maka mkpesa mkpu.

Nkọwapụta batrị na bọọdụ na-eweta ike: 

Ụdị Altronix:	Board na-enye ike	Batrị	20 Min. nke ndabere	4 elekere. nke ndabere	24 elekere. nke ndabere
Oke3	AL600XB220 (Tụtụ aka na Fig. 1a, pg. 7 maka ọnọdụ mgbanwe [SW1] na ọnọdụ)	12VDC/40AH*	N/A	5.0A	N/A
		24VDC/40AH*	N/A	5.4A	0.7A
Oke5	AL1012XB220 (Ụlọ ọrụ atọrọ na 12VDC)	12VDC/12AH	9.0A	Ike batrị maka njikere ihe mberede: opekata mpe 20 min.	N/A
Oke7	Ọnụahịa kasị elu nke AL1024XB2V (Ụlọ ọrụ atọrọ na 24VDC)	24VDC/12AH	7.7A	1.2A	200mA
		24VDC/65AH*	N/A	7.7A	1.2A

*Note: Additional battery enclosure required (Figs. 5-7, pgs. 11-13).

Mpụta Board Na-enye Ike Voltage Ntọala:

Nweta eserese ngwa ngwa njikwa ike (maka ACM8 ọ bụla):

Debe wiwi nwere oke ike na enweghị oke. Jiri opekempe 0.25" oghere. Ihe ruru batrị anọ (4) 12AH nwere ike ịchaji bụ batrị kacha ibu nwere ike dabara na ogige a. Ekwesịrị iji mkpuchi batrị mpụga ma ọ bụrụ na ị na-eji batrị 40AH ma ọ bụ 65AH.

Debe wiwi nwere oke ike na enweghị oke. Jiri opekempe 0.25" oghere. Ihe ruru batrị anọ (4) 12AH nwere ike ịchaji bụ batrị kacha ibu nwere ike dabara na ogige a. Ekwesịrị iji mkpuchi batrị mpụga ma ọ bụrụ na ị na-eji batrị 40AH ma ọ bụ 65AH.
NEC Power-Limited Wiring Requirements for Maximal3V:
Wiring sekit nwere oke na enweghị ike ga-anọrịrị iche na kọbọd. Waịkọ sekit niile nwere oke ike ga-adịrịrị opekata mpe 0.25” pụọ na wiwi sekit ọ bụla na-enweghị oke. Ọzọkwa, eriri sekit niile nwere oke ike na eriri sekit na-enweghị ike ga-abanye ma pụọ ​​​​na kabinet site na ụzọ dị iche iche. Otu dị otú ahụ exampE gosipụtara nke a n'okpuru. Ngwa gị akọwapụtara nwere ike ịchọ ka a ga-eji mkpọpu ikuku dị iche iche. Enwere ike iji ọkpọ ọkpọ ọ bụla mee ihe. Maka ngwa nwere oke ike iji conduit bụ nhọrọ. A ga-emerịrị njikọ wiwi ubi niile na-eji waya CM ma ọ bụ FPL nwere jaket dabara adaba (ma ọ bụ ihe dochie ya).
Mara: Rụtụ aka na eserese njikwa waya dị n'okpuru maka ụzọ kwesịrị ekwesị isi wụnye waya CM ma ọ bụ FPL nwere jaketị (Fig 5a). 

NEC Power-Limited Wiring Requirements for Maximal5V:
Wiring sekit nwere oke na enweghị ike ga-anọrịrị iche na kọbọd. Waịkọ sekit niile nwere oke ike ga-adịrịrị opekata mpe 0.25” pụọ na wiwi sekit ọ bụla na-enweghị oke. Ọzọkwa, eriri sekit niile nwere oke ike na eriri sekit na-enweghị ike ga-abanye ma pụọ ​​​​na kabinet site na ụzọ dị iche iche. Otu dị otú ahụ exampE gosipụtara nke a n'okpuru. Ngwa gị akọwapụtara nwere ike ịchọ ka a ga-eji mkpọpu ikuku dị iche iche. Enwere ike iji ọkpọ ọkpọ ọ bụla mee ihe. Maka ngwa nwere oke ike iji conduit bụ nhọrọ. A ga-emerịrị njikọ wiwi ubi niile na-eji waya CM ma ọ bụ FPL nwere jaket dabara adaba (ma ọ bụ ihe dochie ya).
Mara: Rụtụ aka na eserese njikwa waya dị n'okpuru maka ụzọ kwesịrị ekwesị isi wụnye waya CM ma ọ bụ FPL nwere jaketị (Fig 6a). 

NEC Power-Limited Wiring Requirements for Maximal7V:
Wiring sekit nwere oke na enweghị ike ga-anọrịrị iche na kọbọd. Waịkọ sekit niile nwere oke ike ga-adịrịrị opekata mpe 0.25” pụọ na wiwi sekit ọ bụla na-enweghị oke. Ọzọkwa, eriri sekit niile nwere oke ike na eriri sekit na-enweghị ike ga-abanye ma pụọ ​​​​na kabinet site na ụzọ dị iche iche. Otu dị otú ahụ exampE gosipụtara nke a n'okpuru. Ngwa gị akọwapụtara nwere ike ịchọ ka a ga-eji mkpọpu ikuku dị iche iche. Enwere ike iji ọkpọ ọkpọ ọ bụla mee ihe. Maka ngwa nwere oke ike iji conduit bụ nhọrọ. A ga-emerịrị njikọ wiwi ubi niile na-eji waya CM ma ọ bụ FPL nwere jaket dabara adaba (ma ọ bụ ihe dochie ya).
Mara: Rụtụ aka na eserese njikwa waya dị n'okpuru maka ụzọ kwesịrị ekwesị isi wụnye waya CM ma ọ bụ FPL nwere jaketị (Fig 7a).

Eserese FACP Hook Up:

Fig. 8 Ntinye ngbanwe nke polarity sitere na mmepụta sekit mgbama FACP (a na-ezo aka na polarity na ọnọdụ mkpu):

Eserese FACP nko-elu (na-aga n'ihu):

Maximal3V / Maximal5V / Maximal7V Access Power Controllers (Fused) Installation Guide
Altronix abụghị maka mmejọ ederede ọ bụla.
140 58th Street, Brooklyn, New York 11220 USA
ekwentị: 718-567-8181
faksị: 718-567-9056
websaịtị: www.altronix.com 
ozi-e: info@altronix.com

Akwụkwọ ikike ndụ
IIMaximal3V/5V/7V Series
G27U MEMBER

Akwụkwọ / akụrụngwa

MAXIMAL Maximal V Series Single Power Supply Access Power Controllers [pdf] Ntuziaka nwụnye Maximal V Series Single Power Supply Access Power Controllers, Maximal V Series, Single Power Supply Access Power Controllers, Single Power Supply, Access Power Controllers, Power Controllers, Maximal3V, Maximal5V, Maximal7V

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ