eFlow104NA8 Series Dual mmepụta
Nweta ndị njikwa ike
Ntuziaka nwụnye
eFlow104NA8 Series Dual Output Access Controllers
eFlow104NKA8
- 12VDC ma ọ bụ 5VDC ruo 6A na/ma ọ bụ 24VDC ruo 10A (240W mkpokọta ike) họrọ site na mmepụta.
- Mwepụta fuse echekwabara asatọ (8).
- Asatọ (8) enwere ike họrọ ọdịda ọdịda, ọdịda-echekwa ma ọ bụ ụdị “C” mpụta akọrọ.
- Enwere ike ịwepu njikọ nke mkpu ọkụ site na mmepụta
- Chaja arụnyere maka batrị lead acid ma ọ bụ ụdị gel nwere akara
eFlow104NKA8D
- 12VDC ma ọ bụ 5VDC ruo 6A na/ma ọ bụ 24VDC ruo 10A (240W mkpokọta ike) họrọ site na mmepụta.
- Mpụta asatọ (8) klaasị 2 nwere ikike PTC nwere oke.
- Asatọ (8) enwere ike họrọ ọdịda ọdịda, Fail-Secure, ma ọ bụ ụdị “C” mpụta akọrọ.
- Enwere ike ịhọrọ nkwupu oti mkpu ọkụ site na mmepụta.
- Chaja arụnyere maka batrị lead acid ma ọ bụ ụdị gel nwere akara.
Mkpu. eFlow104NKA8-072220
Ụlọ ọrụ wụnye: _______________ Onye nnọchi anya ọrụ: ________________________________________________
Adreesị: ___________________________________________ Ekwentị #: __________________
gafereview:
Altronix eFlow104NKA8 na eFlow104NKA8D na-ekesa ma gbanwee ike iji nweta usoro njikwa na ngwa. Ha na-atụgharị ntinye 120VAC 60Hz ka ọ bụrụ asatọ (8) na-achịkwa 12VDC ma ọ bụ 24VDC n'onwe ya. Ntinye ntinye abuo nke onye njikwa ike nweta na-enye ohere ka eduzi ya site na abụọ (2) ụlọ nrụpụta arụnyere n'onwe ya obere vol.tage 12 ma ọ bụ 24VDC Altronix ike na-enye asatọ (8) fiusi na-achịkwa onwe ya (eFlow104NKA8) ma ọ bụ PTC (eFlow104NKA8D). Enwere ike ịtụgharị nsonaazụ ike ka ọ bụrụ kọntaktị “C”-akọrọ. A na-arụ ọrụ mmepụta site na sink onye na-anakọta oghe, na-emeghekarị (NO), na-emechi emechi (NC) ntinye mkparị akọrọ, ma ọ bụ mmepụta mmiri si na Access Control System, Card Reader, Keypad, Push Button, PIR, etc. eFlow104NKA8(D) ga- ụzọ ike dị iche iche nke ohere njikwa ngwaike ngwaọrụ gụnyere Mag mkpọchi, Electric Strikes, magnetik Door Holders, wdg. Mpụta ga-arụ ọrụ na ma ọdịda-Safe na/ma ọ bụ Fail-Secure ụdịdị. Interface FACP na-enyere mgbapụ ihe mberede, na nlekota mkpu, ma ọ bụ enwere ike iji kpalite ngwaọrụ inyeaka ndị ọzọ. A na-ahọrọ njirimara nkwụsị ọkụ ọkụ n'otu n'otu maka ihe ọ bụla ma ọ bụ niile nke asatọ (8). Njikọ spade na-enye gị ohere ị nweta ike daisy yinye n'ọtụtụ ACMS8(CB) modul. Njirimara a na-enye gị ohere ikesa ike n'elu ihe ndị ọzọ maka nnukwu usoro.
Nkọwa akwadoro:
| Batrị | Burg. Ngwa 4 elekere. Kwụrụ n'ụsọ/ 15 min. Oti mkpu |
Ngwa ọkụ 24 elekere. Kwụrụ n'ụsọ/ 5 min. Oti mkpu |
Njikwa nnweta Ngwa Kwụrụ n'ụsọ |
| 7 AH | 0.4A/10A | N/A | Nkeji 5/10A |
| 12A11 | 1A/10A | 0.3A/10A | Nkeji 15/10A |
| 40A11 | 6A/10A | 1.2A/10A | Ihe karịrị awa 2 / 10A |
| 65A11 | 6A/10A | 1.5A/10A | Ihe karịrị awa 4 / 10A |
Nkọwapụta:
Ntinye:
eFlow104NB:
- 120VAC, 60Hz, 4.5A.
ACMS8/ACMS8CB: - Ntinye asatọ (8) na-akpalite:
a) Ndenye na-emepekarị (NO) (kọntaktsị kpọrọ nkụ).
b) Ntinye nke emechiri emechi (NC) ( kọntaktị akọrọ).
c) Mepee ntinye sink onye nchịkọta.
d) Ntinye mmiri (5VDC – 24VDC) nwere ihe mgbochi 10K
e) Ngwakọta ọ bụla nke dị n'elu.
Nsonaazụ:
Ike:
- 12VDC ma ọ bụ 5VDC ruo 6A, 24VDC ruo 10A
(240W ngụkọta ike). - Klas inyeaka 2 mmepụta nwere oke ike
akara @ 1A (anaghị agbanwe agbanwe). - Mfefetage nchedo.
ACMS8: - Nsonaazụ echekwabara fuse gosiri @ 2.5A kwa mmepụta, enweghị oke ike. Mkpokọta mmepụta 6A max.
Agafela ọkwa ọkọnọ ike nke onye ọ bụla.
ACMS8CB: - Nsonaazụ echedoro PTC gosiri @ 2A kwa mmepụta, klaasị 2 nwere oke ike. Mkpokọta mmepụta 6A max.
Agafela ọkwa ọkọnọ ike nke onye ọ bụla. - Mpụta asatọ (8) nke a na-achịkwa n'onwe ya ma ọ bụ asatọ (8) nke a na-achịkwa n'onwe ya (lee n'okpuru maka ọkwa):
a) Ọdịda-Nchekwa na/ma ọ bụ ọdịda ike echedoro.
b) Ụdị relays “C” nwere akara @ 2.5A. 12VDC,
Ihe kpatara ike 0.6 (ACMS8 naanị).
c) Mpụta ike inyeaka (anaghị agbanwe agbanwe).
d) Ngwakọta ọ bụla nke dị n'elu. - Enwere ike ịtọ nsonaazụ onye ọ bụla ka ọ bụrụ ọnọdụ gbanyụọ maka ije ozi (mpụta jumper setịpụrụ na ọnọdụ etiti).
Adịghị emetụta ngwa kọntaktị akọrọ. - Nke ọ bụla n'ime fuse asatọ (8) fuse/PTC na-echekwa ike ọkụ nwere ike ịhọrọ ịgbaso ntinye ike 1 ma ọ bụ ntinye 2. Ihe mmepụta vol.tage nke ọ bụla mmepụta bụ otu ihe ntinye voltage nke ntinye ahọpụtara.
- Mbelata ịwa ahụ.
Ogo fuse/PTC:
eFlow104NB:
- Enyere fiusi ntinye aka na 6.3A/250V.
- Igwe batrị nwere ogo 15A/32V.
ACMS8: - Isi ihe ntinye bụ 15A/32V.
- A na-atụle fiusi mmepụta 3A/32V.
ACMS8CB: - Isi ntinye PTC bụ 9A.
- A na-edepụta PTC 2A.
Ndabere batrị (eFlow104NB):
- Chaja arụnyere maka batrị lead acid ma ọ bụ ụdị gel nwere akara.
- Ọnụ ego kachasị ugbu a 1.54A.
- Gbanwee akpaaka ka batrị nọrọ na-echere mgbe AC dara.
Nyefee na ike batrị na-echere bụ ozugbo na enweghị nkwụsị.
Nlekọta (eFlow104NB):
- AC adaghị nlekọta (ụdị kọntaktị “C”).
- Batrị dara na nlekọta ọnụnọ (ụdị kọntaktị "C").
- Nkwụsị ike dị ala. Na-emechi ọnụ ụzọ mmepụta DC ma ọ bụrụ na batrị voltage tụlee n'okpuru 71-73% maka 12V nkeji na 70-75% maka 24V nkeji (dabere na ike ọkọnọ). Na-egbochi mmịpụ batrị miri emi.
Kpupu oti mkpu ọkụ:
eFlow104NB:
- Ikwupu mkpu ọkụ ọkụ na-elekọta (latching ma ọ bụ enweghị ike) 10K EOL resistor. Na-arụ ọrụ na ihe mkpalite na-emepe emepe (NO) ma ọ bụ mechiri emechi (NC).
ACMS8 (CB):
- Ịkwụsị Mkpọ oku ọkụ (latching ma ọ bụ enweghị nkwụsị) bụ nke a na-ahọrọ n'otu n'otu maka ihe ọ bụla ma ọ bụ niile nke asatọ (8).
Nhọrọ ntinye mgbakwụnye ọkụ ọkụ:
a) na-emepekarị [NO] ma ọ bụ na-emechikarị [NC] ntinye kọntaktị akọrọ. Ntinye ngbanwe polarity sitere na sekit mgbama FACP. - Ntinye FACP WET bụ 5-30VDC 7mA.
- Ntinye FACP EOL chọrọ ihe mgbochi njedebe nke 10K.
- FACP mmepụta relay [NC]:
Ma akọrọ 1A/28VDC, 0.6 Ike Factor ma ọ bụ
Nguzogide 10K na [EOL JMP] adịghị.
Ihe ngosi onyonyo:
eFlow104NB:
- Green AC LED: Na-egosi 120VAC dị ugbu a.
- Red DC LED: Na-egosi mmepụta DC.
ACMS8 (CB): - Igwe ọkụ na-acha uhie uhie: Gosipụta ebutere mpụta.
- Igwe ọkụ na-acha anụnụ anụnụ: Na-egosi na agbalitere FACP.
- Onye
Voltagna LEDs: gosi 12VDC (Green) ma ọ bụ 24VDC (Red).
gburugburu:
- Ọnọdụ okpomọkụ na-arụ ọrụ: 0ºC ruo 49ºC ambient.
- iru mmiri: 20 ruo 85%, anaghị ekpo ọkụ.
Akụkụ Mkpuchi (ihe dị ka H x W x D):
15.5" x 12" x 4.5"
(393.7mm x 304.8mm x 114.3mm).
Ntuziaka nwụnye:
Ụzọ waya ga-adị n'usoro iwu eletrik nke mba/NFPA 70/NFPA 72/ANSI, koodu eletriki Canada, yana koodu mpaghara na ndị ọchịchị niile nwere ikike. Ezubere ngwaahịa a maka naanị ime ụlọ.
- Wụnye unit ahụ n'ebe achọrọ. Kaa akara na prerill oghere n'ime mgbidi iji kwụ n'ahịrị n'ahịrị igodo abụọ dị n'elu n'ogige ahụ. Wụnye ihe nkedo abụọ dị elu na skru na mgbidi na isi ihe nkedo na-apụta. Tinye oghere igodo elu nke ogige ahụ n'elu skru abụọ dị elu, larịị, na nchekwa. Kaa akara ọnọdụ nke oghere abụọ dị ala. Wepu ihe mkpuchi ahụ. Gwuo oghere ndị dị ala ma wụnye ihe nkedo abụọ ahụ. Tinye oghere igodo elu nke ogige n'elu skru abụọ dị elu. Wụnye skru abụọ dị ala ma jide n'aka na ị ga-eme ka skru niile sie ike (Mpaghara mkpuchi, pg. 8). Chekwaa ogige ahụ n'ala ala.
- Gbaa mbọ hụ na etinyere jumpers niile na-emepụta [PWR1] - [PWR8] n'ọnọdụ nkwụsị (n'etiti) (Fig 1, pg. 3).
- Jikọọ ike AC anaghị agbanwe (120VAC 60Hz) na njedebe akara [L, N] site na oghere LED dị n'ọnụ ụzọ nke ogige ahụ. Jiri 14 AWG ma ọ bụ karịa maka njikọ ike niile. Waya akwụkwọ ndụ akwụkwọ ndụ dị nchebe na-eduga n'ala ụwa.
Debe wiwi nwere oke ike iche na wiwi na-enweghị ike (Ntinye 120VAC 60Hz, Wires batrị). Ekwesịrị ịnye oghere kacha nta 0.25.
kpachara anya: Emetụla akụkụ ọla ndị ekpughere ekpughe. Mechie ike sekit alaka ụlọ ọrụ tupu ịwụnye ma ọ bụ na-arụ ọrụ. Enweghị akụkụ ndị ọrụ na-arụ ọrụ n'ime.
Tụtụ aka na nrụnye na ọrụ nye ndị ọrụ ruru eru. - Tọọ mmepụta ọ bụla [OUT1] - [OUT8] ka ọ na-ebugharị ike site na ntinye 1 ma ọ bụ 2 (Fig 1, pg. 3).
Rịba ama: tụọ mmepụta voltage tupu jikọọ ngwaọrụ. Nke a na-enyere aka izere mmebi nwere ike ime. - Gbanyụọ ọkụ tupu ị jikọọ ngwaọrụ.
- Nhọrọ mmepụta: eFlow104NKA8(D) ga-enye ihe ruru asatọ (8) mgbanaka ike ma ọ bụ asatọ (8) ụdị akọrọ "C" mmepụta, ma ọ bụ ihe ọ bụla ngwakọta nke ma gbanwee ike na ụdị "C" mmepụta, gbakwunyere asatọ (8) unswitched. ntinye ike inyeaka.
Mwepụta ike gbanwere: Jikọọ ntinye adịghị mma (-) nke ngwaọrụ a na-akwado na njedebe akara [COM].
• Maka ịrụ ọrụ adịghị mma jikọọ ndenye dị mma (+) nke ngwaọrụ a na-akwado na njedebe akara [NC].
• Maka ịrụ ọrụ nchekwa ọdịda jikọọ ndenye dị mma (+) nke ngwaọrụ a na-akwado na njedebe akara [NO].
Mpempe akwụkwọ "C":
Mgbe mpempe akwụkwọ "C" chọrọ, a ga-etinye jumper kwekọrọ (1-8) n'ọnọdụ nkwụsị (Fig 7, pg. 9). N'aka nke ọzọ, enwere ike iwepụ fiusi mmepụta kwekọrọ (1-8) (eFlow104NKA8 naanị).
Jikọọ adịghị mma (-) nke ọkụ ọkụ ozugbo na ngwaọrụ mkpọchi.
Jikọọ mma (+) nke ọkụ ọkụ na ọdụ akara akara [C].
• Maka ịrụ ọrụ adịghị mma jikọọ mma (+) nke ngwaọrụ a na-agbanye na njedebe akara [NC].
• Maka ịrụ ọrụ nchekwa ọdịda, jikọọ mma (+) nke ngwaọrụ a na-agbanye na njedebe akara [NO].
Ndị ana-akpọ nkụ nwere akara @ 2.5A, 28VDC.
Nsonaazụ ike inyeaka (anaghị agbanwe):
Jikọọ ntinye dị mma (+) nke ngwaọrụ a na-akwado na njedebe akara [C] yana adịghị mma (-) nke ngwaọrụ a na-agbanye na njedebe akara [COM]. Enwere ike iji mmepụta nye ike maka ndị na-agụ kaadị, igodo, wdg. - Gbanye isi ike mgbe ejikọrọ ngwaọrụ niile.
- Nhọrọ ntinye ntinye:
Rịba ama: Ọ bụrụ na ejighị mkpọ oku Mgbochi ọkụ, jikọọ resistor 10K ohm na njedebe akara [GND na EOL], gbakwunyere jikọọ jumper na njedebe akara [GND, RST].
Ntinye na-emepe emepe (MKWU):
Mgbanye mgbanaka ntinye njikwa ihe mmịfe DIP banye n'ọnọdụ Gbanyụọ maka [Gbanye 1-8] (Fig 2, n'aka nri). Jikọọ waya gị na ọnụ ahịa akara [+ INP1 -] na [+ INP8 -].
Ntinye na-emechikarị (NC):
Ngbanwe mgbanaka njikwa ntinye mmịfe n'ime ọnọdụ ON maka [Gbanye 1-8]
(Fig 2, n'aka nri). Jikọọ waya gị na ọnụ ahịa akara [+ INP1 -] na [+ INP8 -].
Ntinye ihe nkwokọ mepere emepe:
Jikọọ ntinye sink onye na-anakọta oghere na ọnụ nke akara [+ INP1 -] na [+ INP8 -].
Mmiri (Voltage) Nhazi ntinye:
Jiri nlezianya na-ekiri polarity, jikọọ voltage ntinye wires na-akpalite wires na ihe mgbochi 10K ewepụtara na njedebe akara [+ INP1 -] na [+ INP8 -].
Ọ bụrụ na itinye voltage iji kpalite ntinye – tọọ mgbanwe INP Logic kwekọrọ na ọnọdụ “gbanyụọ”.
Ọ bụrụ na iwepu voltage iji kpalite ntinye – tọọ mgbanwe INP Logic kwekọrọ na ọnọdụ “ON”. - Nhọrọ ihu mkpu ọkụ:
Ntinye [NC] emechiri emechi, nke na-emeghe [NO] ma ọ bụ ndenye ngbanwe polarity sitere na sekit mgbama FACP ga-akpalite nsonaazụ ahọpụtara. Iji mee ka FACP kwupu maka mmepụta, gbanye mgba ọkụ DIP kwekọrọ [SW1-SW8] GBANYE.
Iji gbanyụọ nkwụsị FACP maka mmepụta, gbanyụọ mgba ọkụ DIP kwekọrọ [SW1-SW8]. Mgbanwe ahụ dị ozugbo n'aka ekpe nke Ọkụ Mkpu Interface Terminals.
Ntinye na-emepe emepe:
Kwuo relay FACP gị na ihe mgbochi 10K n'otu n'otu na ọdụ akara [GND] na [EOL].
Ntinye na-emechikarị:
Kwuo relay FACP gị na 10K resistor n'usoro na njedebe akara [GND] na [EOL].
Ihe ntinye sekit mgbama FACP:
Jikọọ ihe dị mma (+) na nke na-adịghị mma (-) site na mmepụta sekit mgbama FACP na njedebe akara [+ FACP -]. Jikọọ FACP EOL na njedebe akara [+ RET -] (a na-ezo aka na polarity na ọnọdụ mkpu).
Kpupu mkpu ọkụ na-adịghị egbochi: Jikọọ jumper na ọnụ ahịa akara [GND, RST].
Ikwupu oti mkpu ọkụ: Jikọọ ngbanwe nrụpụta nrụpụta NO na-emeghe na ọnụ nke akara [GND, RST]. - Mmepụta NC akọrọ FACP:
Jikọọ ngwaọrụ achọrọ ka ọ kpalite site na nsonaazụ kọntaktị akọrọ na njedebe nke akara [NC] na [C].
Mgbe [EOL JMP] na-edobe na-emebi emebi, mmepụta bụ nke 0 Ohm nguzogide na ọnọdụ nkịtị.
Mgbe ebibiri [EOL JMP], a ga-ebufe nguzogide 10k na ngwaọrụ ọzọ mgbe ọ nọ n'ọnọdụ nkịtị. - Njikọ batrị guzoro ọtọ (Fig 6, pg. 8):
Maka ngwa njikwa nnweta US batrị bụ nhọrọ. Achọrọ batrị maka nrụnye Canada (ULC-S319). Mgbe ejighị batrị, mfu nke AC ga-ebute mfu nke mmepụta voltage.
Mgbe achọrọ iji batrị na-echere, ha ga-abụrịrị acid acid ma ọ bụ gel ụdị.
Jikọọ batrị na njedebe akara [- BAT +] (Fig. 4g, pg. 6). Jiri batrị abụọ (2) 12VDC ejikọrọ n'usoro maka ọrụ 24VDC (edu batrị gụnyere). Jiri batrị - Castle CL1270 (12V / 7AH), CL12120 (12V / 12AH), CL12400 (12V / 40AH), CL12650 (12V / 65AH) batrị ma ọ bụ UL ghọtara batrị BAZR2 na BAZR8 nke ọkwa kwesịrị ekwesị. - Ihe nrụpụta batrị na AC (Fig 4, pg. 8):
Achọrọ ijikọ ngwaọrụ na-enye mkpesa nsogbu nlekọta na mpụta akara [AC Fail, BAT Fail] yana nlebanya relay akara [NC, C, NO] na ngwaọrụ ngosi ngosi kwesịrị ekwesị.
Jiri 22 AWG ruo 18 AWG maka AC ọdịda & obere/enweghị mkpesa batrị. - Ka igbu oge mkpesa AC maka awa 2. tọọ ngbanwe DIP [AC Delay] na ọnọdụ gbanyụọ (Fig 4c, pg. 6).
Ka igbu oge mkpesa AC maka nkeji 1. tọọ mgbanwe DIP [AC Delay] gaa na ọnọdụ ON (Fig 4c, pg. 6). - Kwupu oti mkpu ọkụ (Fig. 4c, pg. 6):
Iji mee ka mgbapu mkpu ọkụ tọọ mgba ọkụ DIP [Mkpuchi] na ọnọdụ ON.
Iji gbanyụọ Mwapu Mkpu ọkụ, tọọ mgba ọkụ DIP [Mkpuchi] n'ọkwa gbanyụọ. - Ntinye nke tampmgba ọkụ:
Ugwu UL Edepụtara tamper mgba ọkụ (Altronix nlereanya TS112 ma ọ bụ dakọtara) n'elu nke ogige. Gbanye tamper mgbanaka nkwado n'elu nsọtụ nke ogige ahụ dịka 2" site n'akụkụ aka nri (Fig. 6a, pg. 8).
Jikọọ tampgbanwee wiring gaa na ntinye Ogwe njikwa nnweta ma ọ bụ ngwaọrụ mkpesa UL Edepụtara kwesịrị ekwesị. Iji mee ka mgbaama mkpu rụọ ọrụ, mepee ọnụ ụzọ nke ogige ahụ.
Wiring:
Jiri 18 AWG ma ọ bụ karịa maka obere volta niiletage ike njikọ.
Rịba ama: Lezienụ anya ka sekit nwere oke ike dị iche na wiwi na-enweghị ike (120VAC, Batrị).
Nlekọta:
Ekwesịrị ịnwale otu ahụ ọbụlagodi otu ugboro n'afọ maka ịrụ ọrụ kwesịrị ekwesị dịka ndị a:
Mmepụta Voltage nwale: N'okpuru ọnọdụ ibu nkịtị, mmepụta DC voltage kwesịrị ịlele nke ọma voltage larịị eFlow104NB: 24VDC aha akara @ 10A max.
Nnwale batrị: N'okpuru ibu nkịtị, ọnọdụ lelee na chajịrị batrị zuru oke, lelee voltage (24VDC @ 26.4) ma na ọdụ batrị yana na bọọdụ akara akara [- BAT +] iji hụ na enweghị nkwụsịtụ na wires njikọ batrị.
Rịba amaNchaji kacha ugbu a n'okpuru mwepu bụ 1.54A.
Rịba ama: Ndụ batrị a na-atụ anya ya bụ afọ 5, Otú ọ dị, a na-atụ aro ka ịgbanwee batrị n'ime afọ 4 ma ọ bụ obere ma ọ bụrụ na ọ dị mkpa.
Fig. 4 - eFlow104N nhazi nhazi
Ịdọ aka ná ntị Nsogbu/Oge dị oke maka batrị na-eguzobe:
Maka nrube isi na ULC S318-96, a ga-ejikọta sekit ịdọ aka ná ntị nke oge maka mpaghara ma ọ bụ nke dịpụrụ adịpụ site na Amber ma ọ bụ Red LED iji gosi nsogbu DC (batrị dị ala, ọnwụ batrị ma ọ bụ mgbe 95% nke batrị nọrọ na-echere. depleted). Jikọọ sekit ahụ na kọntaktị Batt Fail relay na ntinye kwesịrị ekwesị nke UL Listed Burglar Alarm ma ọ bụ Ogwe njikwa nnweta. Ọnụọgụ na-esonụ na-egosi sekit dị mkpa maka ịkpọsa mpaghara.
Fig. 5 - Ihe ngosi nsogbu batrị
Maka ojiji Canada, uhie na-egosi lamp a ga-ahụrịrị site na mpụta nke ogige a.
Waya otu ụkwụ nke UL Edepụtara, isi iyi ike nwere oke na-egosi lamp.
Waya ụkwụ nke abụọ nke isi iyi ike na-egosi lamp n'usoro na batrị ada relay contact terminals akara [BAT FAIL – C, NO] (Fig. 5, pg. 6).
Ihe nchọpụta LED:
EFlow104NB ike ọkọnọ/ chaja
| Uhie (DC) | Green (AC/AC1) | Ọkwa inye ike |
| ON | ON | Ọnọdụ ọrụ nkịtị. |
| ON | Gbanyụọ | Mfu nke AC. Batrị njikere na-enye ike. |
| Gbanyụọ | ON | Enweghị mmepụta DC. |
| Gbanyụọ | Gbanyụọ | Mfu nke AC. Achụpụrụ ma ọ bụ enweghị batrị na-echere. Enweghị mmepụta DC. |
ACMS8 na ACMS8CB njikwa ike nnweta
| Ikanam | ON | Gbanyụọ |
| LED 1-Ikanam 8 (Uhie) | Mgbasa ozi (s) arụpụtaghị ike. | Mbupute relay (s) na-enye ike. |
| IHU | Ntinye FACP kpalitere (ọnọdụ mkpu). | FACP nkịtị (ọnọdụ enweghị mkpu). |
| Mpụta akwụkwọ ndụ akwụkwọ ndụ 1-8 | 12VDC | — |
| Mpụta uhie 1-8 | 24VDC | — |
Nchọpụta njedebe:
EFlow104NB ike ọkọnọ/ chaja
| Akụkọ Mgbe Ebighị Ebi | Ọrụ/Nkọwa |
| L, N | Jikọọ 120VAC 60Hz na njedebe ndị a: L na-ekpo ọkụ, N na-anọpụ iche (na-enweghị ike) (Fig 4a, pg. 6). |
| - DC + | 24VDC nominal @ 10A na-aga n'ihu (mpụta na-enweghị ike) (Fig 417, pg. 6). |
| A na-ahụ maka mkpali EOL | Ọkụ mkpu Interface na-akpalite ntinye site na mkpụmkpụ ma ọ bụ FACP. Ntinye ntinye nwere ike imeghe ma mechie ya site na sekit mmepụta FACP (ntinye nwere oke ike) (Fig. 4d, pg. 6). |
| Mba, Ntọgharịa GND | FACP interface latching ma ọ bụ na-enweghị ike (ike-oke) (Fig. 4e, pg. 6). |
| + AUX — | Klas inyeaka 2 mmepụta nwere oke ike nyere akara @ 1 A (anaghị agbanwe agbanwe) (Fig. 41, pg. 6). |
| AC ọdịda NC, C, NO | Na-egosi mfu nke ike AC, dịka ọmụmaatụ jikọọ na ngwaọrụ a na-anụ ma ọ bụ ogwe mkpu. A na-enyekarị ọkụ ọkụ mgbe ike AC dị. Ogo kọntaktị 1A @ 30VDC (ike-oke) (Fig 4b, pg. 6). |
| Bat Fail NC, C, NO | Na-egosi ọnọdụ batrị dị ala, dịka ọmụmaatụ jikọọ na panel mkpu. A na-enyekarị ọkụ ọkụ mgbe ike DC dị. Ogo kọntaktị 1A @ 30VDC. A na-akọ batrị ewepụrụ n'ime nkeji ise. A na-akọ njikọghachi batrị n'ime nkeji 1 (ike-oke) (Fig 4b, pg. 6). |
| - BAT + | Njikọ batrị kwụrụ ọtọ. Ọnụ ego kachasị dị ugbu a 1.54A (na-enweghị ike) (Fig 4g, pg. 6). |
ACMS8 na ACMS8CB njikwa ike nnweta
| Akụkọ Mgbe Ebighị Ebi | Ọrụ/Nkọwa |
| PWR1 - | Ụlọ ọrụ ejikọrọ na eFlow104NB. Ejila ọnụ ọnụ ndị a. |
| PWR2 - | Ụlọ ọrụ ejikọrọ na VR6 voltage regulator. Ejila ọnụ ọnụ ndị a. |
| + INP1 — site na + INP8 — | Asato (8) na-achịkwa onwe ya nke ọma na-emepe emepe (NO), Emechiri emechi (NC), Open Collector Sink or Wet Input Triggers. |
| C, NC | Ihe nrụpụta FACP Dry NC nwere 1A/28VDC © 0.6 Ike Ihe. Klas 2 nwere oke ike. Na EOL JMP emebibeghị, ga-enye nguzogide 10k na steeti nkịtị. |
| GND, RST | FACP interface latching ma ọ bụ enweghị latching. Enweghị ntinye akọrọ. Klas 2 nwere oke ike. A ga-eme ka ọ dị mkpụmkpụ maka interface FACP na-adịghị ejide ma ọ bụ Ntọgharị FACP Latch. |
| GND, EOL | Ọnụ ntinye ntinye FACP na-elekọta EOL maka ọrụ FACP ngbanwe polarity. Klas 2 nwere oke ike. |
| — F, + F, — R, + R | Ihe nrịbama FACP na ntinye sekit na nkwụghachi azụ. Klas 2 nwere oke ike. |
| Mpụta 1 ruo 8 Ọ dịghị C, NC, COM |
Mpụta asatọ (8) nke a na-achịkwa nke onwe ya [Fail-Safe (NC)] ma ọ bụ Fail-Secure (NO)] na asatọ (8) Ụdị "C" Relay na-achịkwa nke onwe ya. |
Foto 6 - eFlow104NKA8(D)
| Nhọrọ nke batrị nkwụnye ụgwọ maka ngwa UL294 Rịba ama: 12V batrị achọrọ maka ULC-S319 nrụnye. |
Nhọrọ nke batrị nkwụnye ụgwọ maka ngwa UL294 Rịba ama: 12V batrị achọrọ maka ULC-S319 nrụnye. |
kpachara anya: Jiri batrị abụọ (2) 12VDC na-echere.
Debe wiwi nwere oke ike na enweghị oke.
Jiri opekempe 0.25" oghere.
Batrị 12AH nwere ike ịchaji bụ batrị kacha ibu nwere ike dabara na ogige a.
Ekwesịrị iji mkpuchi batrị mpụga edepụtara UL ma ọ bụrụ na ị na-eji batrị 40AH ma ọ bụ 65AH.
Eserese ngwa a na-ahụkarị:
Ihe osise 7
Eserese Nkọ:
Fig. 8 – Daisy-chaining otu ma ọ bụ karịa ACMS8(CB) nkeji.
Ekwesịrị itinye EOL Jumper [EOL JMP] na ọnọdụ EOL. Na-adịghị latching.
Fig. 9 – Daisy-chaining otu ma ọ bụ karịa ACMS8(CB) nkeji.
Ekwesịrị itinye EOL Jumper [EOL JMP] na ọnọdụ EOL. Ntọgharị Single.
Fig. 10 – Daisy chaining otu ma ọ bụ karịa ACMS8(CB) nkeji.
Ekwesịrị itinye EOL Jumper [EOL JMP] na ọnọdụ EOL. Ntọgharị n'otu n'otu.
Eserese Nkọ:
| Fig. 11 - Ntinye ngbanwe polarity sitere na mmepụta sekit mgbaàmà FACP (a na-ezo aka na polarity na ọnọdụ mkpu). Na-adịghị latching. |
Fig. 12 - Ntinye ngbanwe polarity sitere na mmepụta sekit mgbaàmà FACP (a na-ezo aka na polarity na ọnọdụ mkpu). Latching. |
 |
 |
| Fig. 13 – Ntinye mkpanaaka emechiri emechi (Na-adịghị egbu egbu). |
Fig. 14 - Ntinye mkpali emechiri emechi (Latching). |
 |
 |
| Fig. 15 – Ọ na-emepe ndenye ihe na-akpalite (Na-abụghị Latching). | Fig. 16 – Na-emepe nke ọma ntinye akpalite (Latching). |
 |
 |
Akụkụ Mkpuchi (BC400):
15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)
Altronix abụghị maka mmejọ ederede ọ bụla.
140 58th Street, Brooklyn, New York 11220 USA | ekwentị: 718-567-8181 | faksị: 718-567-9056
websaịtị: www.altronix.com | ozi-e: info@altronix.com | Akwụkwọ ikike ndụ
IIeFlow104NKA8(D)
G29U
Akwụkwọ / akụrụngwa
 |
Altronix eFlow104NA8 Series Dual Output Access Controllers [pdf] Ntuziaka nwụnye eFlow104NA8 Series Dual Output Access Controllers Power Power, eFlow104NA8 Series, Dual Output Access Power Controllers, Access Power Controllers, Power Controllers, Controllers |
