Altronix AL1024NKA8 Series Dual Output Access Power Controllers Guide nwụnye

Altronix AL1024NKA8 na AL1024NKA8D na-ekesa ma gbanwee ike iji nweta usoro njikwa na ngwa. Ha na-atụgharị ntinye 115VAC 60Hz ka ọ bụrụ asatọ (8) na-achịkwa 12VDC ma ọ bụ 24VDC n'onwe ya. Ntinye ntinye abuo nke onye njikwa ike nweta na-enye ohere ka eduzi ya site na abụọ (2) ụlọ nrụpụta arụnyere n'onwe ya obere vol.tage 12 ma ọ bụ 24VDC Altronix ike na-enye asatọ (8) fiusi na-achịkwa onwe ya (AL1024NKA8) ma ọ bụ PTC (AL1024NKA8D). Enwere ike ịtụgharị nsonaazụ ike ka ọ bụrụ kọntaktị “C”. A na-arụ ọrụ mmepụta site na sink na-emeghe oghere, na-emeghekarị (NO), na-emechi emechi (NC) ntinye mkparị akọrọ, ma ọ bụ mmepụta mmiri si na Access Control System, Card Reader, Keypad, Push Button, PIR, etc. AL1024NKA8(D) ga ụzọ ike dị iche iche nke ohere njikwa ngwaike ngwaọrụ gụnyere Mag mkpọchi, Electric Strikes, magnetik Door Holders, wdg. Mpụta ga-arụ ọrụ na ma ọdịda-Safe na/ma ọ bụ Fail-Secure ụdịdị. Interface FACP na-enyere mgbapụ ihe mberede, nlekota mkpu, ma ọ bụ enwere ike iji kpalite ngwaọrụ inyeaka ndị ọzọ. A na-ahọrọ njirimara nkwụsị ọkụ ọkụ n'otu n'otu maka ihe ọ bụla ma ọ bụ niile nke asatọ (8). Njikọ spade na-enye gị ohere ị nweta ike daisy yinye n'ọtụtụ ACMS8 (CB) modul. Njirimara a na-enye gị ohere ikesa ike n'elu ihe ndị ọzọ maka nnukwu usoro.

Nkọwapụta akwadoro (mkpokọta ugbu a egosiri)

Mpụta	15 min. nke Njikere na 5 min. nke Mkpu	4 elekere. nke Njikere na 5 min. nke Mkpu	24h. nke Njikere na 5 min. nke Mkpu	60h. nke Njikere na 5 min. nke Mkpu
24VDC/12AH Batrị	Njikere = 8A Mkpu = 10A	Njikere = 1.5A Mkpu = 10A	Njikere = 200mA mkpu = 10A	Njikere = 100mA mkpu = 10A
Mpụta	15 min. nke Njikere na 5 min. nke Mkpu	4 elekere. nke Njikere na 5 min. nke Mkpu	24 elekere. nke Njikere na 15 min. nke Mkpu	60 elekere. nke Njikere na 15 min. nke Mkpu
24VDC/65AH Batrị	–	Njikere = 8.0A Mkpu = 10A	Njikere = 1.5A Mkpu = 10A	Njikere = 500mA mkpu = 10A

Maka ngwa njikwa nnweta, ikike batrị maka 10A na-enye ugbu a - 1 awa. maka batrị 24VDC/12AH, elekere 6.5. maka batrị 24VDC/65AH. Hụ mpempe akwụkwọ ngụkọ nha batrị n'okpuru maka batrị ndị ọzọ.

A. AL1024NKA8(D) oriri dị ugbu a (njikere) ________________ 0.05 A
B. Ibu ihe oriri ugbu a (njikere) ________________ A

C. Achọrọ oge echere (awa) ________________ H
D. Ike batrị achọrọ maka njikere (A+B)*C ________________ AH

E. AL1024NKA8(D) oriri ike ime (Mkpu) ________________ 0.05 A
F. Ibu ihe oriri ugbu a (Mkpu) ________________ A

G. Ogologo oge mkpu (awa; 15 Min. = 0.25 Awa) (Mkpu) ________________ H
H. Ike batrị achọrọ maka Mkpu (E+F)*G ________________ AH

I. Ngụkọta ike batrị gbakọrọ D+H ________________ AH
J. Ikike batrị achọrọ I*1.8 (ihe nchekwa) ________________ AH

Mara: AL1024NKA8(D) ike ọkọnọ e mere na-arụ ọrụ na batrị ruo 65AH. Biko mara: ahịrị [I] agaghị agafe 36AH.
Ị ga-ebelata ma nọrọ na njikere oriri ugbu a ma ọ bụ n'oge echere ka ị gbasoo ihe achọrọ. Iji chọpụta nha batrị n'ezie, biko gbaa okirikiri [J] gaa n'ogo batrị kacha nso (dịka 3.5 AH = 4.0 AH).

Nkọwapụta

Ntinye:

AL1024ULXB2:
- 115VAC, 60Hz, 4.2A.

ACMS8/ACMS8CB:
- Ntinye asatọ (8) na-akpalite:
  - a) Ndenye na-emepe nke ọma (MỤGHỊ) (kọntaktsị kpọrọ nkụ).
  - b) Ntinye nke emechiri emechi (NC) (kọntaktsị kpọrọ nkụ).
  - c) Mepee ntinye sink onye nchịkọta.
  - d) Ntinye mmiri (5VDC – 24VDC) nwere ihe mgbochi 10K
  - e) Ngwakọta ọ bụla nke dị n'elu.

Nsonaazụ:

Ike:
- 12VDC ma ọ bụ 5VDC ruo 6A, 24VDC ruo 10A (240W mkpokọta ike).
- Mfefetage nchedo.
ACMS8:
- Nsonaazụ echekwabara fuse gosiri @ 2.5A kwa mmepụta, enweghị oke ike. Mkpokọta mmepụta 6A max. Agafela ọkwa ọkọnọ ike nke onye ọ bụla.
ACMS8CB:
- Nsonaazụ echedoro PTC gosiri @ 2A kwa mmepụta, klaasị 2 nwere oke ike. Mkpokọta mmepụta 6A max. Agafela ọkwa ọkọnọ ike nke onye ọ bụla.
- Mpụta asatọ (8) nke a na-achịkwa n'onwe ya ma ọ bụ asatọ (8) ndepụta ndenye ụdị “C” na-achịkwaghị achịkwa (lee n'okpuru maka ọkwa):
  - a) Ọdịda-Nchekwa na/ma ọ bụ ọdịda ike echedoro.
  - b) Ụdị relays nke “C” bụ @ 2.5A. 12, 24VDC, 0.6 Ike Factor (ACMS8 naanị).
  - c) Ntinye ike inyeaka (anaghị agbanwe agbanwe).
  - d) Ngwakọta ọ bụla nke dị n'elu.
Enwere ike ịtọ nsonaazụ onye ọ bụla ka ọ bụrụ ọnọdụ gbanyụọ maka ije ozi (mpụta jumper setịpụrụ na ọnọdụ etiti). Adịghị emetụta ngwa kọntaktị akọrọ.
Nke ọ bụla n'ime fuse asatọ (8) fuse/PTC na-echekwa ike ọkụ nwere ike ịhọrọ iji soro ntinye ike 1 ma ọ bụ ntinye 2. mmepụta vol.tage nke ọ bụla mmepụta bụ otu ihe ntinye voltage nke ntinye ahọpụtara.
Mbelata ịwa ahụ.

Ogo fuse/PTC:

AL1024ULXB2:
- Ntinye ntinye bụ 5A/250V.
- Igwe batrị nwere ogo 15A/32V.
ACMS8:
- Isi ihe ntinye bụ 15A/32V.
- A na-atụle fiusi mmepụta 3A/32V.
ACMS8CB:
- Isi ntinye PTC bụ 9A.
- A na-edepụta PTC 2A.

Ndabere batrị:

Chaja arụnyere n'ime maka acid a na-emechi ma ọ bụ batrị ụdị batrị.
Gbanwee akpaaka ka batrị nọrọ na-echere mgbe AC dara.
Ọnụ ego kachasị ugbu a 3.6A.

Zero voltage dobe mgbe agbanwere na ndabere batrị.

Nlekọta:

AC dara nlekota (ụdị kọntaktị "C").

Nlekọta batrị dị ala (ụdị kọntaktị "C").
Nlekọta ọnụnọ batrị (ụdị kọntaktị “C”).

Kpupu oti mkpu ọkụ:

Ịkwụsị Mkpọ oku ọkụ (latching ma ọ bụ enweghị nkwụsị) bụ nke a na-ahọrọ n'otu n'otu maka ihe ọ bụla ma ọ bụ niile nke asatọ (8). Nhọrọ ntinye mgbakwụnye ọkụ ọkụ:
- a) Ọ na-emepekarị [NO] ma ọ bụ na-emechikarị [NC] ntinye kọntaktị akọrọ. Ntinye ngbanwe polarity sitere na sekit mgbama FACP.
Ntinye FACP WET bụ 5-30VDC 7mA.

Ntinye FACP EOL chọrọ njedebe 10K nke resistor ahịrị.
FACP mmepụta relay [NC]:
Ma Dry 1A/28VDC, 0.6 Power Factor ma ọ bụ 10K na-eguzogide na [EOL JMP] adịghị.

Ihe ngosi onyonyo:

AL1024ULXB2:
- Green AC LED: Na-egosi 115VAC dị ugbu a.
- Red DC LED: Na-egosi mmepụta DC.

ACMS8 (CB):
- Igwe ọkụ na-acha uhie uhie: Gosipụta na-akpalite nsonaazụ.
- Ikaadị na-acha anụnụ anụnụ: Na-egosi na agbalitere FACP.
- Onye Voltage LEDs: gosi 12VDC (Green) ma ọ bụ 24VDC (Red).

gburugburu:

Ọnọdụ okpomọkụ na-arụ ọrụ: 0ºC ruo 49ºC ambient.

iru mmiri: 20 ruo 85%, anaghị ekpo ọkụ.

Akụkụ Mkpuchi (ihe dị ka H x W x D): 15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm).

Ntuziaka nwụnye

Ụzọ waya ga-adị n'usoro iwu eletrik nke mba/NFPA 70/NFPA 72/ANSI, koodu eletriki Canada yana koodu mpaghara na ndị ọchịchị niile nwere ikike. Ezubere ngwaahịa maka naanị ime ụlọ.

Wunye unit n'ebe achọrọ. Kaa akara na prerill oghere n'ime mgbidi iji kwụ n'ahịrị n'ahịrị igodo abụọ dị n'elu n'ogige ahụ. Wụnye ihe nkedo abụọ dị elu na skru na mgbidi na isi ihe nkedo na-apụta. Tinye oghere igodo elu nke ogige ahụ n'elu skru abụọ dị elu, dị larịị na nchekwa. Kaa akara ọnọdụ nke oghere abụọ dị ala. Wepu ihe mkpuchi ahụ. Gwuo oghere ndị dị ala ma wụnye ihe nkedo abụọ ahụ. Tinye oghere igodo elu nke ogige n'elu skru abụọ dị elu. Wụnye skru abụọ dị ala ma jide n'aka na ị ga-eme ka skru niile sie ike ( Akụkụ mkpuchi, pg. 12). Nchekwa nchebe n'ala ala.
Gbaa mbọ hụ na etinyere jumpers niile [PWR1] - [PWR8] n'ọnọdụ OFF (etiti) (Fig 1, pg. 3).
Jikọọ ike AC akwụghị ụgwọ (115VAC 60Hz) na njedebe akara [L, N] (Fig. 4a, pg. 5). Green “AC” LED na bọọdụ ọkọnọ ike ga-agbanye. Enwere ike ịhụ ọkụ a site na oghere LED na ọnụ ụzọ nke ogige ahụ. Jiri 14 AWG ma ọ bụ karịa maka njikọ ike niile. Ekwentị akwụkwọ ndụ akwụkwọ ndụ waya na-eduga n'ala ala. Debe wiwi nwere oke ike iche na wiwi na-enweghị ike (Ntinye 115VAC 60Hz, Wires batrị). Ekwesịrị ịnye oghere kacha nta 0.25.
kpachara anya: Emetụla akụkụ ọla ndị ekpughere ekpughere aka. Mechie ike sekit alaka ụlọ ọrụ tupu ịwụnye ma ọ bụ na-arụ ọrụ. Enweghị akụkụ ndị ọrụ nwere ike ịrụ ọrụ n'ime. Tụtụ aka na nrụnye na ọrụ nye ndị ọrụ ruru eru.

Tọọ mmepụta ọ bụla [OUT1] - [OUT8] ka ọ na-ebugharị ike site na ntinye 1 ma ọ bụ 2 (Fig 1, pg. 3).
Mara: tụọ mmepụta voltage tupu jikọọ ngwaọrụ. Nke a na-enyere aka izere mmebi nwere ike ime.
Gbanyụọ ọkụ tupu ị jikọọ ngwaọrụ.
Nhọrọ mmepụta: AL1024NKA8(D) ga-enye ihe ruru asatọ (8) mgbanaka ike ma ọ bụ asatọ (8) ụdị akọrọ "C" mmepụta, ma ọ bụ ihe ọ bụla ngwakọta nke ma gbanwee ike na ụdị "C" mmepụta, gbakwunyere asatọ (8) unswitched. ntinye ike inyeaka.
- Mbupute Ike agbanweela:
  Jikọọ ntinye adịghị mma (-) nke ngwaọrụ a na-akwado na njedebe akara [COM].
  - Maka ịrụ ọrụ nchekwa nke Fail-Safe jikọọ ndenye dị mma (+) nke ngwaọrụ a na-akwado na njedebe akara [NC].
  - Maka ịrụ ọrụ nchekwa nke Fail-Secure jikọọ ndenye dị mma (+) nke ngwaọrụ a na-akwado na njedebe akara [NO].
- Mpempe akwụkwọ "C":
  Mgbe mpempe akwụkwọ "C" chọrọ, a ga-etinye jumper kwekọrọ (1-8) n'ọnọdụ nkwụsị (Fig 7, pg. 9). N'aka nke ọzọ, enwere ike wepu fiusi mmepụta kwekọrọ (1-8) (AL1024NKA8 naanị). Jikọọ adịghị mma (-) nke ọkụ ọkụ ozugbo na ngwaọrụ mkpọchi. Jikọọ mma (+) nke ọkụ ọkụ na ọdụ akara akara [C].
  - Maka ịrụ ọrụ nchekwa ọdịda jikọọ mma (+) nke ngwaọrụ a na-akwado na njedebe akara [NC].
  - Maka ịrụ ọrụ nchekwa ọdịda, jikọọ mma (+) nke ngwaọrụ a na-agbanye na njedebe akara [NO]. Ndị ana-akpọ nkụ nwere akara @ 2.5A, 28VDC.
- Nsonaazụ ike inyeaka (anaghị agbanwe):
  Jikọọ ntinye dị mma (+) nke ngwaọrụ a na-akwado na njedebe akara [C] yana adịghị mma (-) nke ngwaọrụ a na-agbanye na njedebe nke akara [COM]. Enwere ike iji mmepụta nye ike maka ndị na-agụ kaadị, igodo igodo wdg.
Gbanye isi ọkụ mgbe ejikọrọ ngwaọrụ niile.
Nhọrọ ntinye ntinye:

Mara: Ọ bụrụ na ejighị nkwupụ mkpu ọkụ ọkụ, jikọọ resistor 10K ohm na ọdụ ndị akara [GND na EOL], gbakwunyere jikọọ jumper na ọdụ ndị akara [GND, RST].
Ntinye na-emepe emepe (MKWU):
Mgbanye mgbanaka njikwa ntinye mmịfe DIP n'ime ọnọdụ Gbanyụọ maka [Gbanye 1-8] (Fig 2, n'aka nri). Jikọọ waya gị na ọnụ ahịa akara [+ INP1 -] na [+ INP8 -].
Ntinye na-emechikarị (NC):
Mgbanye mgbanaka njikwa ntinye mmịfe n'ime ọnọdụ ON maka [Gbanye 1-8] (Fig 2, n'aka nri). Jikọọ waya gị na ọnụ ahịa akara [+ INP1 -] na [+ INP8 -].
Ntinye ihe nkwokọ mepere emepe:
Jikọọ ntinye sink onye na-anakọta oghere na ọnụ nke akara [+ INP1 -] na [+ INP8 -].
Mmiri (Voltage) Nhazi ntinye:
Jiri nlezianya na-ekiri polarity, jikọọ voltage ntinye wires na-akpalite wires na ihe mgbochi 10K ewepụtara na njedebe akara [+ INP1 -] na [+ INP8 -].
Ọ bụrụ na itinye voltage iji kpalite ntinye – tọọ mgbanwe INP Logic kwekọrọ na ọnọdụ “gbanyụọ”.
Ọ bụrụ na iwepu voltage iji kpalite ntinye – tọọ mgbanwe INP Logic kwekọrọ na ọnọdụ “ON”.

Nhọrọ ihu mkpu ọkụ:

Ntinye [NC] emechiri emechi, nke na-emeghe [NO] ma ọ bụ ndenye ngbanwe polarity sitere na sekit mgbama FACP ga-akpalite nsonaazụ ahọpụtara. Iji mee ka FACP kwupu maka mmepụta, gbanye mgba ọkụ DIP kwekọrọ [SW1-SW8] GBANYE. Iji gbanyụọ nkwụsị FACP maka mmepụta, gbanyụọ mgba ọkụ DIP kwekọrọ [SW1-SW8]. Mgbanwe dị ozugbo n'aka ekpe nke Ọkụ Ọkụ Interface Terminals.
Ntinye na-emepe emepe:
Kwuo relay FACP gị na ihe mgbochi 10K n'otu n'otu na ọdụ akara [GND] na [EOL].
Ntinye na-emechikarị:
Kwuo relay FACP gị na 10K resistor n'usoro na njedebe akara [GND] na [EOL].
Ihe ntinye sekit mgbama FACP:
Jikọọ ihe dị mma (+) na nke na-adịghị mma (-) site na mmepụta sekit mgbama FACP na njedebe akara [+ FACP -]. Jikọọ FACP EOL na njedebe akara [+ RET -] (a na-ezo aka na polarity na ọnọdụ mkpu).
Kpupu oti mkpu ọkụ na-adịghị egbochi: Jikọọ jumper na njedebe akara [GND, RST].
Mmepụta NC akọrọ FACP:
Jikọọ ngwaọrụ achọrọ ka ọ kpalite site na nsonaazụ kọntaktị akọrọ na njedebe nke akara [NC] na [C]. Mgbe [EOL JMP] na-edobe na-emebi emebi, mmepụta bụ nke 0 Ohm nguzogide na ọnọdụ nkịtị. Mgbe ebibiri [EOL JMP], a ga-ebufe nguzogide 10k na ngwaọrụ ọzọ mgbe ọ nọ n'ọnọdụ nkịtị.
Njikọ batrị guzoro n'akụkụ (Fig. 6, pg. 8):
Maka ngwa njikwa nnweta US batrị bụ nhọrọ. Achọrọ batrị maka nrụnye Canada (ULC-S319). Mgbe ejighị batrị, mfu nke AC ga-ebute mfu nke mmepụta voltage. Mgbe achọrọ iji batrị na-echere, ha ga-abụrịrị acid acid ma ọ bụ gel ụdị. Jikọọ batrị na ọnụ ahịa akara [- BAT +] (Fig. 4g, pg. 6). Jiri batrị abụọ (2) 12VDC ejikọrọ n'usoro maka ọrụ 24VDC (edu batrị gụnyere). Jiri batrị - Casil CL1270 (12V / 7AH), CL12120 (12V / 12AH), CL12400 (12V / 40AH), CL12650 (12V / 65AH) batrị ma ọ bụ UL ghọtara batrị BAZR2 na BAZR8 nke ọkwa kwesịrị ekwesị.

Ihe nrụpụta batrị na AC (Fig 4, pg. 8):
Jikọọ ngwaọrụ ngosi kwesịrị ekwesị na njedebe akara [AC FAIL & BAT FAIL] (Fig. 4b, pg. 5) nsonazụ nnyefe nlekọta. Jiri 22 AWG ruo 18 AWG maka AC ọdịda & obere/enweghị mkpesa batrị.
Iji gbuo oge ịkọ akụkọ ihe ruru elekere 6, bee jumper “AC Delay” wee tọgharịa ike na otu (Fig 4f, pg. 6).
Kwupu oti mkpu ọkụ (Fig. 4c, pg. 6):
- Iji mee ka Mwapu Mkpu Mkpu ọkụ tọọ ịgbanwee DIP [Mkpuchi] gaa na ọnọdụ ON.
- Iji gbanyụọ mgbanyụọ mkpu ọkụ, tọọ mgba ọkụ DIP [Mkpuchi] ka ọ bụrụ gbanyụọ.
Ntinye nke tampmgba ọkụ:
Ugwu UL Edepụtara tamper mgba ọkụ (Altronix nlereanya TS112 ma ọ bụ dakọtara) n'elu nke ogige. Gbanye tamper mgbanwo akara n'elu nsọtụ nke ogige ahụ dị ka 2" site n'akụkụ aka nri (Fig. 6a, pg. 8). Jikọọ tampgbanwee wiring gaa na ntinye Ogwe njikwa nnweta ma ọ bụ ngwaọrụ mkpesa UL Edepụtara kwesịrị ekwesị. Iji mee ka mgbaama mkpu rụọ ọrụ, mepee ọnụ ụzọ nke ogige ahụ.

Nlekọta

A ga-anwale nkeji opekata mpe otu ugboro n'afọ maka ịrụ ọrụ kwesịrị ekwesị dịka ndị a:

Mmepụta Voltage nwale: N'okpuru ọnọdụ ibu nkịtị, mmepụta DC voltage kwesịrị ịlele nke ọma voltagna ọkwa.
Nnwale batrị: N'okpuru ọnọdụ ibu nkịtị lelee na chajịrị batrị zuru oke, lelee voltaji akọwapụtaratage ma na ọdụ batrị ma na bọọdụ akara akara [- BAT +] iji hụ na enweghị nkwụsịtụ na wires njikọ batrị.

Mara: Nchaji kacha ugbu a n'okpuru mwepu bụ 3.6A.
Mara: Ndụ batrị tụrụ anya bụ afọ 5; Otú ọ dị, a na-atụ aro ịgbanwe batrị n'ime afọ 4 ma ọ bụ obere ma ọ bụrụ na ọ dị mkpa

Ihe oyiyi 4 - AL1024ULXB2 nhazi nhazi

Ikanam Nchọpụta

AL1024ULXB2 - Board ọkọnọ ike

Uhie (DC)	Green (AC)	Ọkwa inye ike
ON	ON	Ọnọdụ ọrụ nkịtị.
ON	Gbanyụọ	Mfu nke AC. Batrị echere na-enye ike.
Gbanyụọ	ON	Enweghị mmepụta DC.
Gbanyụọ	Gbanyụọ	Mfu nke AC. Achụpụrụ ma ọ bụ enweghị batrị na-echere. Enweghị mmepụta DC.

ACMS8 na ACMS8CB njikwa ike nnweta

Ikanam	ON	Gbanyụọ
LED 1-Ikanam 8 (Uhie)	Mgbasa ozi (s) arụpụtaghị ike.	Mbupute relay (s) na-enye ike.
AKWKWỌ	Ntinye FACP kpalitere (ọnọdụ mkpu).	FACP nkịtị (ọnọdụ enweghị mkpu).
Mpụta akwụkwọ ndụ akwụkwọ ndụ 1-8	12VDC	–
Mpụta uhie 1-8	24VDC	–

Nchọpụta njedebe

AL1024ULXB2 - Board ọkọnọ ike

Akụkọ Mgbe Ebighị Ebi	Ọrụ/Nkọwa
L, N	Jikọọ 115VAC na njedebe ndị a: L na-ekpo ọkụ, N na-anọpụ iche (Fig. 4a, pg. 6).
+ DC -	Ụlọ ọrụ ejikọrọ na ACMS8(CB) (Fig. 4d, pg. 6).
AC ọdịda NC, C, NO	A na-eji iji gosi mfu nke ike AC, dịka jikọọ na ngwaọrụ a na-anụ ma ọ bụ ogwe mkpu. Relay na-enwekarị ike mgbe ike AC dị. Ogo kọntaktị 1A @ 28VDC. A na-akọpụta ọdịda AC ma ọ bụ brownout n'ime nkeji 1 nke mmemme. Iji gbuo oge mkpesa ihe ruru elekere 6., bee “AC Delay” jumper wee tọgharịa ike na otu. (Fig. 4 f, pg. 6).
Bat Fail NC, C, NO	A na-eji egosi ọnọdụ batrị dị ala, dịka ọmụmaatụ jikọọ na panel mkpu. Relay na-enwekarị ike mgbe ike DC dị. Ogo kọntaktị 1A @ 28VDC. A na-akọ batrị ewepụrụ n'ime nkeji 1. A na-akọ njikọghachi batrị n'ime nkeji 1. Ọkwa batrị dị ala: ihe dịka 21VDC (Fig 4b, pg. 6).
- BAT +	Njikọ batrị kwụrụ ọtọ. Kachasị ụgwọ dị ugbu a 3.6A (Fig. 4c, pg. 6).

ACMS8 na ACMS8CB njikwa ike nnweta

Akụkọ Mgbe Ebighị Ebi	Ọrụ/Nkọwa
PWR1 -	Factory ejikọrọ na AL1024ULXB2. Ejila ọnụ ọnụ ndị a.
PWR2 -	Ụlọ ọrụ ejikọrọ na VR6 voltage regulator. Ejila ọnụ ọnụ ndị a.
+ INP1 - site na + INP8 –	Asato (8) na-achịkwa onwe ya nke ọma na-emepe emepe (NO), Emechiri emechi (NC), Open Collector Sink or Wet Input Triggers.
C, NC	Mpụta FACP Dry NC nwere 1A/28VDC @ 0.6 Ike Factor. Klas 2 nwere oke ike. Na EOL JMP emebibeghị, ga-enye nguzogide 10k na steeti nkịtị.
GND, RST	FACP interface latching ma ọ bụ enweghị latching. Enweghị ntinye akọrọ. Klas 2 nwere oke ike. A ga-eme ka ọ dị mkpụmkpụ maka interface FACP na-adịghị ejide ma ọ bụ Ntọgharị FACP Latch.
GND, EOL	Ọnụ ntinye ntinye FACP na-elekọta EOL maka ọrụ FACP ngbanwe polarity. Klas 2 nwere oke ike.
- F, + F, - R, + R	Ihe nrịbama FACP na ntinye sekit na nkwụghachi azụ. Klas 2 nwere oke ike.
Mpụta 1 ruo Mmepụta 8 Mba, C, NC, COM	Mpụta asatọ (8) nke a na-achịkwa nke onwe ya [Fail-Safe (NC)] ma ọ bụ Fail-Secure (NO)] na asatọ (8) Ụdị "C" Relay na-achịkwa nke onwe ya.

Foto 6 - AL1024NKA8(D)

kpachara anya: Jiri batrị echere abụọ (2) 12VDC.

Debe wiwi nwere oke ike na enweghị oke. Jiri opekempe 0.25" oghere.

Batrị 12AH nwere ike ịchaji bụ batrị kacha ibu nwere ike dabara na ogige a.
Ekwesịrị iji mkpuchi batrị mpụga edepụtara UL ma ọ bụrụ na ị na-eji batrị 40AH ma ọ bụ 65AH.

Eserese ngwa a na-ahụkarị

Eserese nko-elu

Fig. 8 – Daisy-chaining otu ma ọ bụ karịa ACMS8(CB) nkeji. Ekwesịrị itinye EOL Jumper [EOL JMP] na ọnọdụ EOL. Na-adịghị latching.
Fig. 9 - Daisy-chaining otu ma ọ bụ karịa ACMS8(CB). Ekwesịrị itinye EOL Jumper [EOL JMP] na ọnọdụ EOL. Ntọgharị Single.
Fig. 10 – Daisy chaining otu ma ọ bụ karịa ACMS8(CB) nkeji. Ekwesịrị itinye EOL Jumper [EOL JMP] na ọnọdụ EOL. Ntọgharị n'otu n'otu.

Eserese nko-elu

Fig. 11 - Ntinye ngbanwe nke polarity sitere na mmepụta sekit mgbaàmà FACP (a na-ezo aka na polarity na ọnọdụ mkpu). Na-adịghị latching
Fig. 12 - Ntinye ngbanwe polarity sitere na mmepụta sekit mgbaàmà FACP (a na-ezo aka na polarity na ọnọdụ mkpu). Latching

Fig. 13 - Ntinye mkpanaaka emechiri emechi (Na-adịghị ejigide).
Fig. 14 - Ntinye mkpali emechiri emechi (Latching).
Fig. 15 – Mepee ndenye mkpasa na-emekarị (anaghị ejide ya)

Fig. 16 – Na-emepe nke ọma ntinye akpalite (Latching).

Akụkụ Mkpuchi (BC400)

15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)

Altronix abụghị maka mmejọ ederede ọ bụla. 140 58th Street, Brooklyn, New York 11220 USA

ekwentị: 718-567-8181
faksị: 718-567-9056

websaịtị: www.altronix.com
ozi-e: info@altronix.com
Akwụkwọ ikike ndụ

Akwụkwọ / akụrụngwa

Altronix AL1024NKA8 Series Dual Output Access Controllers [pdf] Ntuziaka nwụnye
AL1024NKA8, AL1024NKA8D, AL1024NKA8 Series Dual Output Access Controllers, Dual Output Access Power Controllers, Access Power Controllers, Dual Exput Power Controllers, Power Controllers.

Ntụaka

Akwụkwọ ntuziaka onye ọrụ

Altronix AL1024NKA8 Series Dual Output Access Controllers

gafereview