XTOOL XTS500 Wireless Diagnostics Module User Manual

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to the Wi-Fi selection page of your PC. Select WLAN 2 and search for the Wi-Fi hotspot with the same name as the SN of the device.
Once connected, your PC has established a connection with the device.

Njikọ Ahịrị

Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

Akpachara anya maka nchọpụta ọrịa

Ensure proper connections are made and follow safety protocols while performing diagnostics on vehicles.

About J2534 Toolbox
To install J2534 Toolbox:

Lelee koodu QR ma ọ bụ gaa na ya
https://www.xtooltech.com/english/DownloadCenter.html to find the installation pack.
Mepee ihe ebudatara file and run Setup.exe. Follow the installation process.
After installation, restart your PC for changes to take effect.

Otu esi eji
To use J2534 Toolbox:

For wired connection: Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will detect the device automatically.
If not detected, click the Refresh button to try again.
For wireless connection: Plug in the WiFi Receiver, click the WiFi button, select WLAN 2, find the matching hotspot, and connect.
Ensure a stable connection before proceeding with diagnostics.

Akara ụghalaahia
XTOOL is a trademark of Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders.

Mkpesa nke akwụkwọ ikike na mmachi nke ụgwọ
All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Xtool reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Xtool will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product.

Before operating or maintaining this unit, please read this manual carefully, please pay extra attention to the safety warnings and precautions.

Nkwado & Ọrụ

Ndị ọchịchị Websaịtị: www.kpo.ok.com
Email: xtoolinplusus@outlook.com

Okwu mmalite

Outlook & ọdụ ụgbọ mmiri

OBDII-16 port: Connect to vehicle’s DLC port.
Nameplate: Show device information.
Type-C Port: Connect the device to diagnosis PC via wire.
Indicator Light: Show device status.

Agba ọkụ na-egosi	Ihe ngosi ìhè pụtara
Ọkụ ndụ ndụ siri ike	Kwadoro na
Ìhè akwụkwọ ndụ akwụkwọ ndụ na-egbuke egbuke	Na-emelite ngwa ngwa
Ọkụ na-acha anụnụ anụnụ siri ike	Device connected (no communication)
Ìhè na-acha anụnụ anụnụ na-egbuke egbuke	Communicating with the vehicle
Ìhè uhie na-egbuke egbuke	Mmejọ ngwaọrụ

Na-amalite

Njikọ Ugbo ala

Njikọ ikuku

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Plug the USB wireless receiver into the USB port of the PC.
Go to Wi-Fi selection page of your PC. Select “WLAN 2”, and search for the Wi-Fi hotspot that has the same name as the SN of the device.
Once the hotspot is connected, your PC has established connection with the device.

Njikọ Ahịrị

Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
Connect the VCI and the diagnostic PC with a USB Type-C cable.

Akpachara anya maka nchọpụta ọrịa

Voltage nso na ụgbọ ala: +9 ~ + 36V DC;
When testing some special functions, the operator must operate according to the prompts and meet the test conditions. In some cases, the conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
Usoro njikwa eletrọnịkị nke ụdị dị iche iche dị mgbagwoju anya. Ọ bụrụ na ị na-ezute ọnọdụ ebe ọ na-agaghị ekwe omume ịnwale ma ọ bụ ọnụ ọgụgụ buru ibu nke data nyocha bụ ihe na-adịghị mma, ị nwere ike ịchọ ECU nke ụgbọ ala wee họrọ menu maka ihe nlereanya na aha ECU;
Naanị eriri wiring nke XTOOL nyere na nke emebere maka ngwaọrụ ka ekwenyere ka eji ya na ngwaọrụ a iji zere imebi ụgbọ ala ma ọ bụ ngwaọrụ;
When running a diagnostics session, DO NOT shut down the device directly. You should cancel the task before returning to the main interface and then shutting down the device.

About J2534 Toolbox
J2534 Toolbox is a PC application that manage the updates and operation logs for all VCIs that supports J2534 function. Before you start working on diagnostics with your PC, make sure you have the J2534 Toolbox installed.

Nwụnye

Scan the QR code on the right, or go to:https://www.xtooltech.com/english/DownloadCenter.html
And find “J2534 Toolbox” for the installation pack.
After the download is completed, unzip it and click “Setup.exe”, then follow the installation process. We suggest you to restart your PC after installation.

Otu esi eji

The picture on the right shows the main screen of the J2534 Toolbox when the VCI is not connected to the diagnostic PC.

Device Connection – Wired

Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will automatically detect the device when you connect it.
If the status has not been refreshed after you connect the VCI via wire, click the Refresh button to try again.

Device Connection – Wireless

Plug in the WiFi Receiver that comes with the VCI box.
Click the WiFi button on the bottom-left corner and select “WLAN 2” (or other numbers)
Find the hotspot that names the same as the SN of the VCI box and click “Connect”.
When the connection is ready, you are OK to go.

Isi ihuenyo
When the VCI is connected, you will see this screen:

SN: Shows the SN of the current VCI.
Firmware Version: Shows current firmware version that is installed on the VCI.
Driver Version: Shows current driver version that is installed on the VCI.
J2534 Authorization: Shows the VCI authorization status of current VCI.

Log Record: Turn on/off the J2534 communication logs recording.
Feedback: Send feedback to XTool customer service team when you meet any issues regarding the J2534 connection.

Firmware/Driver Update

If there is an update for the firmware or the driver, you will see a red dot beside the version number. Click the Update button on the right to check updates.
You can choose the version first, and click “Upgrade” button on the right to start updates.
DO NOT DISCONNECT THE VCI WHEN THE UPDATE IS IN PROGRESS!

Ntọala

Click the “Settings” button on the top-right corner and go to the Toolbox settings.
Languages: Click to change language shown on the Toolbox.
Version Number: Check the updates of the Toolbox.
Log Cache: Show the size of the log folder. You can click the button on the right to clear all logs.
Save Location: This shows the location of the log folder. You can click this to get into the folder.

DoIP Mode Switch: When there are cases that the vehicle asks for a DoIP connection, please turn on the switch to enable DoIP mode. Please note that the DoIP mode can only be enabled in wired connection.

Nzaghachi

If you meet any issues regarding J2534 connection, please record the logs (turn on the log recording switch) and send the logs to XTool customer service team. To better locate your problems, we need the following information in the report:

Adreesị ozi ịntanetị gị
Ndekọ files, recorded when the issues happened
Vehicle information (brand, model, MY)
Firmware/Driver version info
A brief description on what is going on (you can also attach images & screenshots)

Our customer service team will handle this and reply to you via email.

Nkwekọrịta FCC

FCC ID: 2AW3IV01W2

Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:

Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ
Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.

Ịdọ aka ná ntị
Mgbanwe ma ọ bụ mgbanwe ndị otu na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ngwa ahụ.

Rịba ama
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Megharịa ma ọ bụ bugharịa antenna nnata.
Mee ka nkewa dị n'etiti akụrụngwa na onye nnata.
Jikọọ akụrụngwa na ntinye na sekit dị iche na nke ejikọrọ onye nnata.
Kpọtụrụ onye na-ere ahịa ma ọ bụ onye ọrụ redio/TV nwere ahụmahụ maka enyemaka.

Ndị Na-ahụ Maka Ọrụ

Aha ụlọ ọrụ: FCC US Agent, LLC
Adreesị: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA
Email: Nkwado@FCCUSAgent.com

Nkwupụta ISD

IC: 29441-V01W2
Model: XTS500
PMN: V120，XTS500
HVIN: V01W2A

Ngwaọrụ a nwere ihe mbufe / nnata (s) enweghị ikike nke na-agbaso Innovation, Science and Economic Development RSS(s) enweghị ikike nke Canada. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:

Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya.
Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla, gụnyere nnyonye anya nwere ike bute ịrụ ọrụ ngwaọrụ a na-achọghị.

Nkwuwapụta nkwekọ
N'ihi nke a, Shenzhen XTOOLtech Intelligent Co., Ltd na-ekwupụta na nke a Ikuku Diagnostic Module bụ na nnabata na mkpa chọrọ na ndị ọzọ mkpa ndokwa nke Directive 2014/53/EU. Dabere na Nkeji edemede 10(2) na Nkeji edemede 10(10), ngwaahịa a kwere ka ejiri ya na mba ndị otu EU niile.

UKCA

N'ihi nke a, Shenzhen XTOOLtech Intelligent Co., Ltd na-ekwupụta na nke a Ikuku Diagnostic Module na-eju afọ niile ụkpụrụ nka na ọdabara ngwaahịa n'ime akporo UK Radio Equipment Regulations (SI 2017/1206); Ụkpụrụ eletriki eletriki (Nchekwa) UK (SI 2016/1101); na UK Electromagnetic Regulations Compatibility (SI 2016/1091) wee kwuwapụta na etinyeghị otu ngwa ahụ n'aka ụlọ ọrụ UK kwadoro.
Shenzhen Xtooltech Intelligent Co., Ltd.
Tinye: 17&18/F, Ụlọ A2, Creative City, Liuxian Avenue, Nanshan District, Shenzhen, China
Shenzhen HQ Tel: +86 755 2399608
Email: marketing@xtooltech.com

Ajụjụ

What operating system does XTS500 J2534 support?

The device only support Windows 7/8/10/11 or later version.

Why can’t my Mac recognize this device?

The device does not support macOS system.

Does the device need to be activated for usage?

This device need no S/N or activation code to activate the device. It will work directly with OE software once connection.

What functions can this device achieve?

This device can do what OE dignostic software do. Please check the compatibility before usage.

Dose the device include OE software?

OE software is not included in the package. You need to subscribe the OE software from manufacturer.

Akwụkwọ / akụrụngwa

XTOOL XTS500 Wireless Diagnostics Module [pdf] Akwụkwọ ntuziaka onye ọrụ
XTS500 Wireless Diagnostics Module, XTS500, Wireless Diagnostics Module, Diagnostics Module, Module

Ntụaka

Akwụkwọ ntuziaka onye ọrụ

XTOOL XTS500 Wireless Diagnostics Module

Nkọwapụta

Ntuziaka ojiji ngwaahịa