Wụnye Nduzi
CSEN1
CSEN1 Combo Sensor Controller
Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)
Nkọwa
The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.
Nkọwapụta
- Ugboro redio: 2.4 GHz (IEEE 802.15.4)
- Ike mmepụta RF: +20dBM
- Okpomọkụ na-arụ ọrụ: -40° ruo +70°C
- Iru mmiri na-arụ ọrụ: 10 ruo 95%, anaghị ekpo ọkụ
- Ihe mkpuchi IP66 kwadoro
- Akụkụ: 3.1" D x 1.6" H (80mm D x 42mm H)
- Input Power: 12-24VDC, 35mA max, 840mW
- Nzube nke njikwa: Ịrụ ọrụ
- Environmental: Indoor/Outdoor
- ogo mmetọ: 3
- Ogo mkpali Voltagihe: 330V
Ntụle imewe
Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltagnke 10V DC.
- Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
- Mee ka wires na-emepe emepe pụọ na ahịrị AC ma ọ bụrụ na ọ ga-ekwe omume.
- Kachasị nke 4 DALI-2/D4i LED Drivers kwa onye njikwa, gakwuru nkwado Synapse ma ọ bụrụ na achọrọ oke ka ukwuu.
- Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
- Abanyela na heatsink ma ọ bụ na onye ọkwọ ụgbọ ala LED.
IHE: Ọkwọ ụgbọala LED ga-akwadorịrị ịrụ ọrụ DIM ka gbanyụọ.
Ịdọ aka ná ntị na ịdọ aka ná ntị
- TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
- Ọdịda ịgbaso ntuziaka na ịdọ aka ná ntị ndị a nwere ike imebi akwụkwọ ikike ahụ.
- This product must be installed in accordance with national, state, and local electrical codes and requirements.
- If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.
Nkọwa waya nke akwụkwọ ZHAGA 18 SOCKET
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:
- 12-24VDC POWER: Brown
- Common Ground/DALI-: Pink with White Stripe
- DALI+/DIM+: Violet with White Stripe
- Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length
Foto 1 
Ntuziaka ntinye
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- Ọ bụrụ na ọdabara, wepụ ihe mkpuchi mkpuchi ma ọ bụ ngwaọrụ njikwa ọkụ arụnyere ugbu a n'ime ebe nchekwa ihe.
- Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
- After alignment, push until the CSEN1 is fully seated within the receptacle.
- While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)
Mara: Iji rụọ ọrụ nke ọma, jide n'aka na etinyere njikwa ahụ kpamkpam n'ime oghere wee tụgharịa n'ime ọnọdụ akpọchiri.
Ịdọ aka ná ntị: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
Foto 2
Ọkwa ọkụ ọkụ
| Ikanye ike | Ọnọdụ |
| Acha anụnụ anụnụ | On for 3 seconds at Startup, then Off |
| Ọnọdụ LED | Ọnọdụ |
| Uhie | No script on the device |
| Uhie na-egbuke egbuke | Njehie nzikọrịta ozi |
| Blue na-egbuke egbuke | Communication, No Config |
| Green na-egbuke egbuke | Normal Operation with Motion |
| Gbanyụọ | Normal Operation, no Motion |
Ozi iwu na asambodo
Nkwupụta Ngosipụta RF: Ngwa a na-akwado oke mkpughe radieshon FCC ewepụtara maka gburugburu enweghị njikwa. Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na anya kacha nta nke 20cm n'etiti radiator na ahụ gị. Agaghị ejikọta ihe nnyefe a ma ọ bụ na-arụ ọrụ na njikọ antenna ma ọ bụ nnyefe ọ bụla ọzọ.
Asambodo ụlọ ọrụ Canada (IC): Ngwa dijitalụ a agaghị agafe oke klaasị B maka mkpọtụ ụda redio sitere na ngwa dijitalụ nke edobere na Iwu nnyonye anya Redio nke Ngalaba Nkwukọrịta nke Canada.
Asambodo FCC na ozi nchịkwa (naanị USA)
FCC Nkebi 15 Klas B: Ngwaọrụ a na-akwado akụkụ 15 nke iwu FCC. Ọrụ dị n'okpuru ọnọdụ abụọ ndị a: (1) Ngwaọrụ ndị a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ, yana (2) Ngwa ndị a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nke nwere ike ibute ọrụ na-emerụ ahụ.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): A nwalere ngwa a wee hụ na ọ dabara na oke maka ngwaọrụ dijitalụ Klas B, dịka akụkụ 15 nke iwu FCC. Emebere oke ndị a iji nye nchebe ezi uche dị na ya megide nnyonye anya na-emerụ emerụ na ntinye ụlọ. Akụrụngwa a na-ewepụta, na-eji, ma nwee ike ịgbasa ike ugboro redio yana, ọ bụrụ na etinyeghị ya ma jiri ya dịka ntuziaka siri dị, nwere ike ibute ndabichi na-emerụ ahụ na nkwukọrịta redio. Agbanyeghị, enweghị nkwa na nnyonye anya agaghị eme na otu nrụnye. Ọ bụrụ na akụrụngwa a na-ebute nnyonye anya na-emerụ ahụ na nnabata redio ma ọ bụ telivishọn, nke enwere ike ikpebi site na ịgbanyụ ma gbanye akụrụngwa, a na-agba onye ọrụ ume ka ọ nwaa idozi nnyonye anya site n'otu ma ọ bụ karịa n'ime usoro ndị a: (1) Re-orient. ma ọ bụ bugharịa antenna nnata; (2) Mee ka nkewa dị n'etiti akụrụngwa na onye nnata; (3) Jikọọ akụrụngwa n'ime oghere na sekit dị iche na nke ejikọrọ onye nnata; (4) Kpọtụrụ onye na-ere ahịa ma ọ bụ onye ọrụ redio/TV nwere ahụmahụ maka enyemaka.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:
- Nkeji 15, Nkebi nke B, maka akụrụngwa klaasị B
- FCC 96-208 dị ka ọ na-emetụta kọmpụta B nkeonwe na mpụta
- A nwalere ngwaahịa a na ụlọ nyocha Mpụga nke akwadoro maka iwu FCC wee hụ na ọ zutere FCC, akụkụ 15, oke ikuku. Agbanyere akwụkwọ file dị na Synapse Wireless, Inc.
Ọ bụrụ na FCC ID maka modul n'ime mkpuchi ngwaahịa a anaghị ahụ anya mgbe etinyere ya n'ime ngwaọrụ ọzọ, mgbe ahụ n'èzí ngwaọrụ etinyere ngwaahịa a ga-egosipụtakwa akara na-ezo aka na FCC ID modul agbakwunyere. Mgbanwe (FCC 15.21):
Mgbanwe ma ọ bụ mgbanwe na akụrụngwa a nke Synapse Wireless, Inc., akwadoghị nke ọma, nwere ike imebi ikike onye ọrụ iji rụọ akụrụngwa a.
Emebere ikike - akara ngosi mebere na https://www.synapsewireless.com/about/patents
Iji mụtakwuo nleta: synapsewireless.com
Asambodo
| Nlereanya | CSEN1-H-W-ZHA (white enclosure) or CSEN1-H-G-ZHA (gray enclosure) |
| Nwere FCC ID | QOQ-GM240P |
| Nwere IC | 5123A-GM240P |
| RoHS 3 | 2011/65/EU (2015/863) |
| EU erute | (EC) Mba 1907/2006 |
Onye njikwa ngwa DALI-2 enwetara ikike
Akwụkwọ / akụrụngwa
 |
Synapse CSEN1 Combo Sensor Controller [pdf] Ntuziaka nwụnye CSEN1-H-W-ZHA, CSEN1-H-G-ZHA, CSEN1 Combo Sensor Controller, CSEN1, Combo Sensor Controller, Sensor Controller, Controller |