SpeedyBee F405 V3 njikwa ụgbọ elu

Nkọwapụta gafereview

Akụkụ

Ndụmọdụ dị mkpa maka ịwụnye ngwugwu ụgbọ elu

Biko hụ na etinyere ngwugwu ụgbọ elu ahụ n'ụzọ ọkọlọtọ, na njikwa ụgbọ elu (FC) n'elu yana njikwa ọsọ eletrọnịkị (ESC) na ala. Ka ịgbanwee ntụzịaka gyroscope na usoro moto, jiri “Ntọala.” Ekpuchighị mmebi ọ bụla sitere na nrụnye na-ezighi ezi n'okpuru akwụkwọ ikike anyị.

 

• Ụdị nwụnye ọkọlọtọ
• Usoro nwụnye egosiri ezighi ezi ma nwee ike ibute kọntaktị ozugbo n'etiti FC na ESC.

ngwugwu

Nhọrọ 1 – SpeedyBee F405 V4 55A 30×30 Stack

1. Onye na-ahụ maka ụgbọ elu SpeedyBee F405 V4 x 1
2. SpeedyBee BLS 55A 4-in-1 ESC x 1
4. 35V 1000uF obere ESR Capacitor x 1
5. M3 Nylon Nut x 5
6. M3 silicone O mgbanaka x 5
7. M3*8mm silicon Grommets (maka FC) x 1
8. M3 * 8.1mm Silicone Grommets (maka ESC) x 1
9. SH 1.0mm 25mm-ogologo 8pin USB(maka njikọ FC-ESC) x 1 SH 1.0mm 75mm-ogologo 8pin USB* x 1
10. M3 * 30mm mkpuchi ime-hexagon x 5
11. DJI 6pin USB (80mm) x 1
12. Igwe ọkụ XT60 (70mm) x 1

Mgbe ọdụ ESC chere ihu n'ihu drone, jiri eriri a maka njikwa ụgbọ elu na ESC; nsọtụ abụọ ahụ na-agbanye n'otu n'otu.

Nhọrọ 2 – SpeedyBee F405 V4 Njikwa ụgbọ elu

1. Onye na-ahụ maka ụgbọ elu SpeedyBee F405 V4 x 1
2. M3*8mm silicon Grommets (maka FC) x 1
3. SH 1.0mm 25mm-ogologo 8pin USB(maka njikọ FC-ESC) x 1
4. DJI 6pin USB (80mm) x 1

Nhọrọ 3 – SpeedyBee BLS 55A 4-in-1 ESC

1. SpeedyBee BLS 55A 4-in-1 ESC x 1
2. 35V 1000uF obere ESR Capacitor x 1
3. M3 silicone O mgbanaka x 5
4. Igwe ọkụ XT60 (70mm) x 1
5. SH 1.0mm 25mm-ogologo 8pin USB(maka njikọ FC-ESC) x 1
6. M3 * 8.1mm Silicone Grommets (maka ESC) x 1

Njikọ FC & ESC

Jiri eriri 8-pin dị na ngwugwu jikọọ FC na ESC. Ma ọ bụ na-ere waya 8 ozugbo na pad 8 na nsọtụ ọ bụla.

Usoro 1 - Iji eriri 8-pin
Jiri njedebe ọ bụla nke eriri JST 8-pin jikọọ FC na ESC.

 

Usoro 2 - Direct soldering
Solder 8 wires na pads 8 na nsọtụ nke ọ bụla na-ezo aka na nkọwa pad dị n'okpuru.

Nkebi 2 – F405 V4 Onye njikwa ụgbọ elu

Nhazi

Nkọwa ihe ngosi LED

• Uhie Uhie - Ihe Ngosi Ike.Red siri ike mgbe ọ gbasịrị.
• GREEN LED – Ọkwa Bluetooth. Green siri ike na-egosi ejikọrọ Bluetooth.
• BLUE LED – Ọkụ njikwa ụgbọ elu nke firmware njikwa ụgbọ elu na-achịkwa.
• Ikanam oroma – Ngosipụta ọnọdụ njikwa ọkụ. Ọ na-egosi na 4 set nke LED ibe ejikọrọ na LED1-LED4 pad na nkuku nke ụgbọ elu njikwa na-achịkwa Betaflight firmware (BF_LED mode) ma ọ bụ Bluetooth mgbawa (SB_LED mode).
• Orange siri ike: na-egosi na 4 x LED dị na ọnọdụ SB_LED. Na ọnọdụ a, mgbe agbanyere FC yana na ọnọdụ nọrọ na njikere, pịa bọtịnụ BOOT ka ịgbanye ụdị ngosi nke LED.
• Gbanyụọ: na-egosi na 4 x LEDs na-achịkwa ngwa ngwa Betaflight. Pịa bọtịnụ ogologo maka sekọnd 3 ka ịgbanwee ụdị njikwa n'etiti ọnọdụ BF_LED na ọnọdụ SB_LED.
• Bọtịnụ BOOT
  • [A] Naanị ọ bụrụ na onye na-ahụ maka ụgbọ elu na-ama brik ma enweghị ike ịgbalite, biko soro usoro ndị a ka iweghachite firmware maka ya:

1.  Fanye eriri USB A na TYPE-C na PC gị.
2.  Pịa ma jide bọtịnụ BOOT, tinye eriri USB n'ime njikwa ụgbọ elu, wee hapụ bọtịnụ BOOT.
3. Mepee onye nhazi Betaflight/INAV na PC, gaa na ibe 'Firmware Flashing', họrọ ebumnuche 'SPEEDYBEEF405V4' wee gbaa ọkụ.

[B]. Mgbe agbanyere FC na ọnọdụ nọrọ na njikere, enwere ike iji bọtịnụ BOOT jikwaa eriri LED ejikọrọ na paịlị LED1-LED4 na nkuku. Mkpirisi pịa bọtịnụ BOOT ka ịgbanye ọnọdụ ngosi LED. Pịa bọtịnụ BOOT ogologo ka ịgbanwee n'etiti ọnọdụ SpeedyBee-LED na ọnọdụ BF-LED. N'okpuru ọnọdụ BF-LED, ngwa ngwa Betaflight ga-ejikwa eriri LED1-LED4 niile. Ụdị ndabara bụ ọnọdụ BF-LED.

Njikọ Peripheral FC

• Cheta na1: Ka egbochie ikpokọta ihe ọkụ site na voltage spikes na ike elu, a na-atụ aro nke ukwuu iji obere ESR capacitor na ngwugwu.
• Note2: FC na ESC nwekwara ike ijikọ site na ire ere ozugbo. Nkọwa nke paịlị ịre ahịa bụ nke a.

Njikọ USB vs DJI O3 Air Unit
Jiri eriri 6-pin na-abịa na nkeji ikuku O3

Njikọ USB vs RunCam Link/ Caddx Vista Air Unit

• Jiri eriri 6-pin na-abịa na nchịkọta F405 V4
• (Lee ngwa No.11 na ngalaba ngwugwu)

Njikọ USB vs DJI Air Unit V1

• Jiri eriri 6-pin na-abịa na nchịkọta F405 V4
• (Lee ngwa No.11 na ngalaba ngwugwu)

Ozi dị mkpa maka nnata SBUS

Mgbe ị na-eji ihe nnata SBUS, eriri mgbaàmà SBUS nke onye na-anata ga-ejikọta ya na pad SBUS dị n'ihu nke onye na-ahụ maka ụgbọ elu (pad a n'ime ime na-eji UART2).
Ọ bụrụ na ị na-ejikwa DJI Air Unit (O3/Link/Vista/Air Unit V1), ị ga-achọ ịkwụpụ waya mgbama SBUS na
Ngwa ikuku Unit. Emeghị nke a ga-egbochi nnabata SBUS nke onye njikwa ụgbọ elu mara nke ọma. Ị nwere ike iji tweezers wepụta waya SBUS site na njikọ njikọ 6-pin (ma ọ bụ bee waya a ozugbo) ma kpochie akụkụ nke waya ahụ nke ọma.

Ozi dị mkpa maka nnata ELRS

Anyị na-akwado ijikọ TX nnata ELRS na RX na paịlị T2 na R2 dị na njikwa ụgbọ elu. Agbanyeghị, mgbe ị na-eji DJI Air Unit n'otu oge, ụfọdụ ndị na-anata ELRS nwere ike ọ gaghị amata nke ọma site na njikwa ụgbọ elu. Ọ bụrụ n'ịhụta nsogbu a, ịkwesịrị ịkwụpụ waya mgbama SBUS site na njigide ikuku. Ị nwere ike iji tweezers wepụ waya SBUS site na njikọ njikọ 6-pin
(ma ọ bụ bepụ waya a ozugbo) ma kpochie ihe ekpughere
akụkụ nke waya nke ọma.

Ngwa & FC nhazi

Nweta ngwa SpeedyBee
Chọọ 'SpeedyBee' na Google Play ma ọ bụ App Store. Ma ọ bụ budata Android .apk file na anyị websaịtị: https://www.spedybee.com/download.

Nhazi FC

FC Firmware Mmelite
SpeedyBee F405 V4 njikwa ụgbọ elu anaghị akwado ikuku firmware na-egbu maramara, yabụ biko gbanye ya firmware na PC gị na-eso usoro ndị a:

1.  Jikọọ eriri USB jikọọ njikwa ụgbọ elu na PC
2.  Mepee onye nhazi Betafight/INAV na PC gị. Were Betaflight configurator dị ka example, gaa na ibe 'Firmware Flashing', họrọ ebumnuche 'SPEEDYBEEF405V4' wee gbaa ọkụ.

Nkọwapụta

Aha ngwaahịa	SpeedyBee F405 V4 30×30 Njikwa ụgbọ elu
MCU	STM32F405
IMU (Gyro)	ICM42688P
Portdị Ọdụ USB	Ụdị-C
Barometer	Wuru n'ime
OSD Mgbawa	AT7456E mgbawa
Bluetooth BLE	Akwadoro. Ejiri ya maka nhazi njikwa ụgbọ elu (MSP kwesịrị inye ya na ọnụego Baud 115200 na UART4)
WIFI	akwadoghị
Ụzọ Njikọ nke DJI Air Unit	Ụzọ abụọ akwadoro: njikọ 6-pin ma ọ bụ soldering ozugbo.
6-pin DJI Ikuku Nkwụnye	Akwadoro. Dakọtara kpamkpam na DJI O3/RunCam Link/ Caddx Vista/DJI Air Unit V1, ọ dịghị waya achọrọ ka ọ gbanwee.
Oghere kaadị Blackbox MicroSD	*Betaflight firmware chọrọ ụdị kaadị microSD ka ọ bụrụ ọkọlọtọ (SDSC) ma ọ bụ ikike dị elu (SDHC) n'okpuru 32GB, yabụ anaghị akwado kaadị ikike ịgbatị (SDXC) (Ọtụtụ kaadị U3 dị elu bụ SDXC). Ọzọkwa, a ga-eji usoro FAT16 ma ọ bụ FAT32 (akwadoro) hazie kaadị microSD. Yabụ, ịnwere ike iji kaadị SD ọ bụla na-erughị 32GB, mana Betaflight nwere ike ịmata naanị 4GB kacha. Anyị na-atụ aro ka ị jiri nke a Nhazi otu nke atọ ngwá ọrụ wee họrọ 'Degharịa usoro' wee hazie kaadị gị. Leleekwa Ebe a maka kaadị SD akwadoro ma ọ bụ zụta ya nwalere kaadị site na ụlọ ahịa anyị.
Ntinye ihe mmetụta ugbu a	Akwadoro. Maka SpeedyBee BLS 55A ESC, biko tọọ ọnụ ọgụgụ = 400 na Offset = 0.
Ntinye ike	3S - 6S Lipo (Site na G, BAT pin / pads sitere na njikọ 8-pin ma ọ bụ 8-pads n'akụkụ ala)
5V mmepụta	Otu 9 nke mmepụta 5V, paịlị + 5V anọ na pad 1 BZ + (eji maka Buzzer) n'akụkụ ihu, yana paịlị 4x LED 5V. Ngụkọta ibu dị ugbu a bụ 3A.
9V mmepụta	Otu abụọ nke mmepụta 2V, otu + 9V pad n'akụkụ ihu na ndị ọzọ gụnyere na njikọ dị n'akụkụ ala. Ngụkọta ibu dị ugbu a bụ 9A.
3.3V mmepụta	Akwadoro. Emebere ya maka ndị nnabata 3.3V. Ihe ruru 500mA dị ugbu a.
4.5V mmepụta	Akwadoro. Ezubere maka nnata na modul GPS ọbụlagodi mgbe ejiri FC na ọdụ ụgbọ USB. Ruo 1A dị ugbu a.
Akara ngosi ESC	M1 - M4 n'akụkụ ala na M5-M8 n'akụkụ ihu.
UART	6 sets (UART1, UART2, UART3, UART4 (Raarara onwe ya nye maka njikọ Bluetooth)), UART5 (Raarara nye maka ESC telemetry), UART6
ESC Telemetry	UART R5(UART5)
I2C	Akwadoro. SDA & SCL paịlị n'akụkụ ihu. A na-eji magnetometer, sonar, wdg.
Omenala Betaflight LED Pad	Akwadoro. 5V, G na paịlị LED na ala nke akụkụ ihu. Ejiri ya maka WS2812 LED nke Betaflight firmware na-achịkwa.
Buzzer	BZ+ na BZ-pad ejiri maka 5V Buzzer
Bọtịnụ BOOT	Akwadoro.
	[A]. Pịa ma jide bọtịnụ BOOT na ike FC n'otu oge ahụ ga-amanye FC ịbanye na ọnọdụ DFU, nke a bụ maka ngwa ngwa na-egbuke egbuke mgbe FC na-agbanye brik.
	[B]. Mgbe agbanyere FC na n'ọnọdụ nọrọ na njikere, enwere ike iji bọtịnụ BOOT jikwaa eriri LED ejikọrọ na njikọ LED1-LED4 n'akụkụ ala. Site na ndabara, obere pịa bọtịnụ BOOT ka ịgbanye ọnọdụ ngosi LED. Pịa bọtịnụ BOOT ogologo ka ịgbanwee n'etiti SpeedyBee-LED mode na BF-LED mode. N'okpuru ọnọdụ BF-LED, firmware Betaflight ga-ejikwa eriri LED1-LED4 niile.
Ntinye RSSI	Akwadoro. Akpọrọ aha dị ka RS n'akụkụ ihu.
Ọdụ ụgbọ mmiri Smart / F.Port	akwadoghị
Firmware Onye njikwa ụgbọ elu akwadoro	BetaFlight(ndabere), INAV
Aha Target Firmware	SPEEDYBEEF405V4
Ịkwanye	30.5 x 30.5mm ( dayameta oghere 4mm)
Akụkụ	41.6 (L) x 39.4 (W) x 7.8 (H) mm
Ibu	10.5g

Nkebi nke 3 – SpeedyBee BLS 55A 4-in-1 ESC

Njikọ na njikwa ụgbọ elu & Motors

• Cheta na1: Ka egbochie ikpokọta ihe ọkụ site na voltage spikes na ike elu, a na-atụ aro nke ukwuu iji obere ESR capacitor na ngwugwu.
• Note2: FC na ESC nwekwara ike ijikọ site na ire ere ozugbo. Nkọwa nke paịlị ịre ahịa bụ nke a.

Nhazi ESC

• Ị nwere ike iji SpeedyBee APP hazie ESC a na ikuku maka ma BLHeli_S ma ọ bụ Bluejay firmware. Nzọụkwụ:

• Ị nwekwara ike iji PC configurators hazie ESC a. Anyị na-akwado ESC Configurator. Biko jiri ihe nchọgharị Google Chrome wee gaa:http://www.esc-configurator.com.

ESC Firmware Mmelite

• Nke a 8-bit 55A ESC nwere ike ịgba ọsọ BLHeliS ma ọ bụ Bluejay firmware. Ejikwa BLHeliS firmware na ndabara. Ị nwekwara ike gbanye ya na Bluejay firmware nke nwere ike ịkwado nzacha RPM na Bi-directional Dhsot. Nzọụkwụ firmware na-egbuke egbuke bụ ndị a:?
• Wepu propellers niile na drone gị.
• Gbaa mbọ hụ na ejikọrọ onye na-ahụ maka ụgbọ elu nke ọma na ESC, wee gbalite drone. Nzọụkwụ a na-eme ka o doo anya na ESC na-amalite nke ọma.
• Jikọọ ihe njikwa ụgbọ elu na kọmputa site na iji eriri USB Ụdị-C.
• Mepee ihe nchọgharị Chrome wee gaa na nke a
• websaịtị: https://www.esc-configurator.com/
• Soro usoro ndị na-egbuke egbuke femụwe dị ka egosiri na nseta ihuenyo dị n'okpuru. Ihe dị mkpa: Na interface nke 6, a ga-ahọrọ ụdị "ESC" dị ka "JH-40".

Nkọwapụta

Aha ngwaahịa	SpeedyBee BLS 55A 30×30 4-in-1 ESC
Firmware	BLHeli_S JH-40
Njikọ nbudata PC Configurator	https://esc-configurator.com/
Na-aga n'ihu ugbu a	55A* 4
Burst Ugbu a	70 (sekọnd iri)
TVS nchekwa diode	Ee
Mpụga Capacitor	1000uF Low ESR Capacitor (na ngwugwu)
ESC Protocol	DSOT300/600
Ntinye ike	3-6S LiPo
Mpụta ike	VBAT
Ihe mmetụta dị ugbu a	Nkwado (Ọnọdụ = 400 kwụsịrị = 0)
ESC Telemetry	akwadoghị
Ịkwanye	30.5 x 30.5mm ( dayameta oghere 4mm)
Akụkụ	45.6 (L) * 44 (W) * 8mm (H)
Ibu	23.5g

 

Akwụkwọ / akụrụngwa

SpeedyBee F405 V3 njikwa ụgbọ elu [pdf] Akwụkwọ ntuziaka onye ọrụ Onye na-ahụ maka ụgbọ elu F405 V4, BLS 55A 4-in-1 ESC, F405 V3 Njikwa ụgbọ elu, F405 V3, Stack Controller, Stack Control, Stack

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ