SoliTek SOLID Series Solar Modules Installation Guide

SoliTek SOLID Series Solar Modules

Ntuziaka ojiji

• Read this guide entirely before installation.
• This document provides minimum requirements and recommendations for safe and successful installation of SoliTek PV modules and is necessary to retain compliance with IEC 61215, IEC 61730, and UL 61730 standards.
• This guide provides basic information on JSC SoliTek Cells SOLID series photovoltaic modules, including their installation and safe handling.
• All instructions should be read and understood before attempting installation. Contact your dealer or JSC SoliTek Cells for further information if needed.
• This documentation refers to the PV modules themselves and is not a comprehensive installation manual for personnel not specifically trained in PV modules.
• It serves as a general but strictly mandatory reference for the installer. Infringement or inaccurate observance of any clause in this documentation voids the warranty.
• The installer must understand and follow all applicable local, state, and federal regulations and standards for building construction, electrical design, fire, and safety.
• Check with local authorities for permitting requirements before installing or maintaining PV modules, and become familiar with mechanical and electrical requirements for photovoltaic systems.
• Ọdịda ịgbaso ntuziaka dị na ntuziaka a nwere ike imebi akụrụngwa sistemụ, tinye ndị ọrụ n'ihe egwu, mebie akụrụngwa, ma ọ bụ mebie akwụkwọ ikike panel.
• Rooftop PV systems should only be installed on dwellings formally analyzed for structural integrity and confirmed to be capable of handling the additional weighted load of PV system components (including PV modules) by a certified building specialist or engineer.

NKWUO GBASARA YA

• Biko gụọ akwụkwọ ntuziaka a kpamkpam tupu echichi.
• Ebumnuche nke akwụkwọ a bụ ịnye opekempe chọrọ yana ndụmọdụ maka nrụnye SoliTek PV dị mma na nke ọma.
• Akwụkwọ a nwekwara ihe ndị achọrọ iji dowe SoliTek PV modul kwekọrọ na ụkpụrụ IEC 61215, IEC 61730, UL 61730.
• Ntuziaka a nwere ozi bụ isi gbasara JSC “SoliTek Cells” SOLID usoro fotovoltaic modul, ntinye ha na njikwa nchekwa. Ekwesịrị ịgụ ma ghọta ntuziaka niile tupu ị nwaa nrụnye. Ọ bụrụ na enwere ajụjụ ọ bụla, biko kpọtụrụ onye na-ere gị ma ọ bụ JSC “SoliTek Cells” maka ozi ndị ọzọ.
• This documentation refers to the PV-modules themselves and is not meant to be a complete installation manual for personnel not specifically trained to PV-modules.
• It serves as a general but strictly mandatory reference for the Installer.
• Mmebi ma ọ bụ idebe ezighi ezi nke akụkụ ọ bụla nke akwụkwọ a na-emebi akwụkwọ ikike.
• Onye nrụnye ga-aghọta ma soro usoro iwu obodo, steeti na gọọmentị etiti niile dị na ụkpụrụ maka iwu ụlọ, imewe ọkụ, ọkụ na nchekwa, ma ga-enyocha ndị ọchịchị obodo iji chọpụta ikike ikike tupu ị nwaa ịwụnye ma ọ bụ dokwaa modul PV ma kwesịrị. mara nke ọma na igwe na eletriki chọrọ maka sistemu fotovoltaic.
• Ọdịda ịgbaso ntuziaka dị na ntuziaka a nwere ike imebi akụrụngwa sistemu, tinye ndị ọrụ n'ihe egwu, mebie akụrụngwa, ma ọ bụ mebie akwụkwọ ikike panel.
• Ekwesịrị ịwụnye sistemu PV dị n'elu ụlọ naanị n'ụlọ ndị nyochara nke ọma maka iguzosi ike n'ezi ihe n'usoro wee gosi na ha nwere ike ijikwa ibu ọzọ dị arọ nke akụrụngwa sistemu PV, gụnyere modul PV, site n'aka onye ọkachamara ụlọ ma ọ bụ injinia gbaara ama.
• For your safety, do not attempt to work on a rooftop until safety precautions have been identified and taken, including, without limitation fall protection measures, ladders or stairways, and personal protective equipment (PPE).
• For your safety, do not install or handle PV modules under adverse conditions, including, without limitation strong or gusty winds, and wet or frosted roof surfaces.
• Ihe owuwu PV nke dị larịị nwere mgbakọ sel anwụ nke kpuchiri n'ime ihe mkpuchi n'ime mpempe iko abụọ.
• Debe akwụkwọ a na ebe nchekwa maka ntụnye aka n'ọdịnihu.
• Anwala ịkwasa modul ahụ, ma ewepụkwala akara aha ma ọ bụ ihe ọ bụla agbakwunyere! Ime otú ahụ ga-emebi akwụkwọ ikike.

Ijikwa & Ngwa

Ijikwa

• SoliTek PV modules must be transported in the supplied packaging only and kept in the packaging until they are ready to be installed.
• Protect pallets against movement and exposure to damage during transportation. Secure pallets from falling over.
• Agafela elu kacha elu nke pallets a ga-ekpokọta, dịka egosiri na nkwakọ ngwaahịa pallet.
• Store pallets in a cool and dry location until the PV modules are ready to be unpackaged.
• SoliTek PV modules are heavy and should be handled with care. Never use the junction box or cables as a grip.
• Do not exert mechanical stress on the cables.
• Never step on PV modules or drop or place heavy objects on them.
• Be careful when placing PV modules on hard surfaces and secure them from falling.
• Broken glass can result in personal injury. PV modules with broken glass cannot be repaired and must not be used.
• Broken or damaged PV modules must be handled carefully and disposed of properly.

Ngwa

Mmachibido

• SoliTek PV modules must be mounted on appropriate mounting structures positioned on suitable buildings, the ground, or other structures suitable for PV modules (e.g. carports, building facades or PV trackers).
• PV modules must not be mounted on moving vehicles of any kind. Modules must not be installed in locations where they could be submerged in water.
• Do not install modules above 2000 m (6561 ft) altitude above sea level
• Agaghị eduzi ọkụ gbadoro anya na arụrụ arụ na modul SoliTek PV.

Nkwanye

• SoliTek na-atụ aro ka wụnye modul PV n'akụkụ opekempe tilt nke ogo 10 iji nye ohere maka nhicha onwe ya nke ọma site na mmiri ozuzo.
• Ndo nke akụkụ ma ọ bụ zuru ezu nke modul PV ma ọ bụ modul nwere ike ibelata arụmọrụ sistemụ.
• SoliTek na-atụ aro ibelata oke ndò n'ime afọ niile iji mee ka ume ike nke modul PV na-emepụta.
• Sistemu dị elu voltages could be induced in the event of an indirect lightning strike, which could cause damage to PV system components.
• The open area of wire loops should be minimized in order to reduce the risk of lightning-induced voltagọ na -eme.
• Igwe ikuku ikuku ka mma na eriri njikọ dị mkpụmkpụ na-abawanye mmepụta ike eletrik.

Maka modul bifacial:

• A na-atụ aro ka ịbawanye elu panel PV site na ala ka ìhè dịkwuo n'okpuru modul wee tụgharịa uche
• Uru bifacial na-abawanye nke ukwuu ma ọ bụrụ na etinyere modul n'elu ọcha (uru albedo dị elu), na-egosipụta ìhè.

Ntinye eletriki

Nchekwa

• PV modul nwere ike ịmepụta ugbu a na voltage mgbe ekpughere ìhè nke ike ọ bụla. Igwe ọkụ eletrik na-abawanye na ike ọkụ dị elu. DC voltage nke 50 Volts ma ọ bụ karịa nwere ike igbu ya. Ịkpọtụrụ sekit dị ndụ nke sistemu PV na-arụ ọrụ n'okpuru ọkụ nwere ike ibute ujo ọkụ eletrik na-egbu egbu.
• Wepu modul PV ume site n'iwepụ ha kpamkpam na ọkụ ma ọ bụ site na iji ihe na-adịghị mma kpuchie ihu ha. Banyere ụkpụrụ nchekwa maka ngwa eletrik dị ndụ mgbe ị na-arụ ọrụ na modul ndị na-ekpughere ọkụ ọ bụla. Jiri ngwaọrụ mkpuchi ma anaghị eyi ọla ọla mgbe ị na-arụ ọrụ na modul PV.
• Ka ịzenarị mgbaba na ujo eletrik, akwụsịla njikọ eletrik n'okpuru ibu. Njikọ na-ezighi ezi nwekwara ike ịkpata mgbaba na ujo eletrik. Debe njikọ dị ọcha ma dị ọcha ma hụ na ha nọ n'ọnọdụ ọrụ kwesịrị ekwesị. Etinyekwala ihe ọla n'ime njikọ ma ọ bụ gbanwee ha n'ụzọ ọ bụla iji chekwaa njikọ eletrik.
• Do not touch or handle PV modules with broken glass unless the PV modules are first disconnected, and you are wearing proper PPE. Avoid handling PV modules when they are wet unless cleaning the PV modules as directed in this manual. Never touch electrical and wet connections without protecting yourself with insulated gloves.
• The modules are qualified for Class II protection against electrical shock, in accordance with clause 4 of IEC 61730-1:2016, which can be used in systems operating at > 50 V DC or >240 W, where general contact access is anticipated and modules qualified for safety through UL 61730 within this application class are considered to meet the requirements of Safety Class II.
• Ịwụnye usoro fotovoltaic anyanwụ chọrọ nkà na ihe ọmụma pụrụ iche. Ekwesịrị ịrụ ya naanị site n'aka ndị ọrụ tozuru oke na ndị nkuzi pụrụ iche. Onye nrụnye na-eche ihe egwu niile nke mmerụ ahụ, gụnyere ihe egwu nke ujo eletrik.
• Jiri naanị akụrụngwa, njikọ, wiring na ngwaike mgbago emebere maka ojiji na sistemụ fotovoltaic.
• Before any manipulation at an installed PV plant, switch it off first on the AC-side, and then on the DC side of the inverter or the charge controller.
• Mgbe ị na-ewepụ wires ejikọrọ na modul fotovoltaic nke na-ekpuchi ọkụ, arc eletrik nwere ike ime. Arcs nwere ike ịkpata ọkụ, malite ọkụ, ma ọ bụ na-emepụta nsogbu nchekwa (ruo na ọkụ eletrik na-egbu egbu).
• Lelee voltage before starting and observe the local safety-relevant regulations for such working conditions.
• N'okpuru ọnọdụ nkịtị, modul fotovoltaic nwere ike ịmepụta ihe dị ugbu a na / ma ọ bụ voltage (ebe a: 30V DC) karịa ka akọwara na ọnọdụ ule ọkọlọtọ.
• Kpọtụrụ na DC voltage nke 30 V ma ọ bụ karịa nwere ike ịdị ize ndụ. Kpachara anya mgbe ị na-eji wiwi ma ọ bụ na-ejikwa modul ekpughere na ìhè anyanwụ.
• Naanị jikọọ modul nwere otu ihe nrụpụta ugbu a na usoro. Ọ bụrụ na ejikọrọ modul n'usoro, mkpokọta voltage nhata na nchikota nke modul onye ọ bụla voltages.
• Naanị jikọọ modul ma ọ bụ usoro nchikota modul nwere otu voltage in parallel. If modules are connected in parallel, the total current is equal to the sum of the individual module or series combination currents.
• Jiri otu ụdị modul mgbe niile n'ime otu sistemụ fotovoltaic.
• If the sum of short circuit currents of the parallel-connected modules exceeds the reverse current, string diodes or fuses have to be used in each string of modules connected in parallel. These string diodes or fuses have to be qualified for the maximum expected current and voltage. The fuse rating value is also corresponds to the maximum reverse current that a module can withstand. The reverse current value can be found on the product label, in the product datasheet or in chapter 8 of the installation manual. Observe the instructions and safety precautions for all other components used in the system, including wiring and cables, connectors, DC-breakers, inverters, etc.
• Jiri akụrụngwa nchekwa kwesịrị ekwesị (ngwaọrụ mkpuchi, mkpuchi dielectric, akpụkpọ ụkwụ na wdg) akwadoro maka nrụnye ọkụ eletrik.

Nhazi

• N'okpuru ọnọdụ nkịtị, modul fotovoltaic nwere ike ịnweta ọnọdụ ndị na-emepụta ihe dị ugbu a na / ma ọ bụ voltage than reported at Standard Test Conditions (STC: 1000 W/ m2, AM 1.5, and 250C/770F cell temperature) or Bifacial nominal power index(BNPl front irradiance 1000 W/m2, back irradiance 135 W/m2 AM 1.5, and 25 OC/770F cell temperature). The short-circuit current (ISC) should be multiplied by a factor of 1.25 and the open-circuit voltage (VOC) kwesịrị ịba ụba site na ihe ruru 1.25 dabere na ọnọdụ okpomọkụ kachasị dị ala na nke kachasị elu edere maka ebe nrụnye mgbe ị na-achọpụta akụrụngwa vol.tage ratings, eduzi ugbu a ratings, fuse nha, na size nke njikwa jikọọ na PV mmepụta.
• Voltages bụ ihe mgbakwunye mgbe ejikọtara modul PV ozugbo n'usoro, na modul modul na-agbakwunye mgbe PV modul jikọtara ozugbo n'otu n'otu. Agaghị ejikọta modul PV nwere àgwà eletrik dị iche iche ozugbo n'usoro. Iji ngwaọrụ eletrọnịkị nke atọ dabara adaba ejikọrọ na modul PV nwere ike mee ka njikọ eletrik dị iche iche ma a ga-etinyerịrị ya dịka ntuziaka onye nrụpụta si dị.
• Oke voltage of serial interconnection of the modules must be less than the maximum certified module’s system voltage. Ọzọkwa, kacha ntinye voltage nke inverter na nke ngwaọrụ eletriki ndị ọzọ dị na usoro a ga-eburu n'uche. Oghere sekit voltage of the array string needs to be calculated at the lowest expected a mbient temperature forthe location. The maximal system voltage for the module is indicated in the module’s datasheet.
• Accordingly, for BLACKSTAR, SOLID or MAGNUS series modules, the values of ISC and VOC under STC or BNPI marked on this module should be multiplied by a factor of 1,25 when determining component voltage ratings, conductor current ratings, fuse sizes, and size of controls connected to the PV output. In the USA, referto Section 690-8 of the National Electrical Code (N EC) for an additional multiplying factor of 125 percent (80 percent de-rating) which may be applicable.

Ngwaọrụ Nchekwa Ọdịnihu (OCPD)

• When the potential reverse current of a PV string exceeds the rated SoliTek PV module series fuse rating (values indicated at the module datasheet) an overcurrent protection device (OCPD) must be used.
• An overcurrent protection device is required for each series string if more than two series are connected in parallel.
• In this case, it is needed to use one fuse per string rated at 1.25 x Isc or higher (Isc is the PV module’s short circuit current at STC). A PV fuse on each PV string will protect the PV modules and conductors from overcurrent faults and help minimize any safety hazards.
• The PV fuse will also isolate the faulted PV string so the balance of the PV system can continue to generate electricity.
• Fuse amp ogo ≥ 1.25 x Isc
• Họrọ ọkwa ọkwa dị elu na-esote na katalọgụ nke PV Fuses dị.
• Isc = Mkpirisi okirikiri ugbu a nke otu modul na Ọnọdụ Nlereanya Standard (STC).
• N'ịtụle ụkpụrụ nke Isc nke SoliTek modul, uru ziri ezi nke PV Fuses nke a ga-eji na ntinye bụ 30 A. SoliTek na-atụ aro iji fuses PV na ma ndị na-eduzi ihe dị mma na ndị na-adịghị mma.

CABLE & WIRING

A na-enye modul SoliTek PV nwere ọkọlọtọ abụọ, eriri ọkụ na-eguzogide anwụ na-akwụsị na njikọ PV dị njikere maka ọtụtụ nrụnye. Ọnụ ọnụ (+) dị mma nwere njikọ nwoke ebe njedebe (-) na-adịghị mma nwere njikọ nwanyị. Ezubere wiring modul maka njikọ usoro (ya bụ, nwoke (+) na nwanyị (-) njikọ njikọ) mana enwere ike iji jikọọ ngwaọrụ eletriki ndị ọzọ dabara adaba nwere ike ịnwe nhazi wiring ọzọ ma ọ bụrụhaala na eso ntuziaka onye nrụpụta.
Jiri wiwi mpaghara nwere mpaghara obe kwesịrị ekwesị nke akwadoro maka ojiji n'oge kacha mkpụmkpụ mkpirisi nke modul PV. Wiring niile ga-abụrịrị mkpuchi okpukpu abụọ, eriri jikọtara ya na oke kacha nta nke 1,8 kV (karịa 1500 V vol.tage) na opekempe a kwadoro nke 90 ˚C (190 Celsius F). Ogo waya adịghị ihe na-erughị 4 mm² (12 AWG). Ụdị mkpuchi kwesịrị ekwesị maka ụdị usoro nrụnye a na-eji, ọ ga-emezurịrị IEC 61730 na Safety Class II chọrọ.

• Ọkwa mkpuchi: 1,8 kV (eduzi-eduzi).
• Okpomọkụ: -40°C ruo +90°C (-40°F ruo 190°F) opekata mpe.
• Ihe owuwu nke onye na-eduzi: waya ọla kọpa nwere tinned strands na ọla kọpa dị ọcha karịa 99,9%.
• Ihe mkpuchi nke mbụ: polyethylene na-ejikọta ya (XLPE), ìhè anyanwụ na mmiri na-eguzogide, ọkụ ọkụ. Kwesịrị ekwesị maka okporo ụzọ na ụzọ ọgba ọsọ arụnyere n'okpuru ala.
• Mkpuchi (jaketị): thermoplastic, ìhè anyanwụ na-eguzogide, ọkụ ọkụ, mmiri na-eguzogide.
• Dayameta mpụta nke eriri USB kacha nta nwere mkpuchi - 5,2 mm (2,05 inch).
• Nke kacha nta eduzi cross-ngalaba – 4 mm² (12 AWG).

SoliTek na-atụ aro ka ndị nrụnye jiri naanị eriri anwụ na-egbochi ọkụ ruru eru maka wiwi ozugbo (DC) na sistemụ PV. Ekwesịrị idobe eriri na nrụnye nrụnye n'ụzọ ga-eme ka a ghara imebi mmebi nke eriri USB na / ma ọ bụ modul. Etinyela nrụgide na eriri. Maka idozi, jiri ụzọ dabara adaba, dị ka eriri eriri na-eguzogide anwụ na/ma ọ bụ obere njikwa waya. Ọ bụ ezie na eriri ndị ahụ enweghị ìhè anyanwụ na-egbochi mmiri, ebe enwere ike, zere ikpughe ìhè anyanwụ kpọmkwem na imikpu mmiri nke eriri.
Standard ogologo nke cables si junction igbe bụ 1,2 m (47,24 inch). A na-atụ anya na panel abụọ ga-ejikọta na sistemụ ahụ.

NTỌ

• Module grounding must be done in accordance with the electrical design and construction specifications, procedures, regulations and other special grounding requirements applicable to the installation sites. If grounding is needed, it should be done accordingly:

Framed type modules grounding
Enwere ike iji oghere ndị nwere akara ntọ ala na etiti ahụ naanị maka ịkwa ala. Agwula oghere ndị ọzọ n'ala na etiti modul.
The grounding conductor or strap may be copper, copper alloy, or any other material acceptable foruse as an electrical conductor in accordance with local electric codes and regulations.
Onye na-eduzi ala ga-emezi njikọ na ụwa site na iji electrode ala ala kwesịrị ekwesị.
A bolted connection is required; it incorporates:

• Nha bolt nke M4.
• Ihe ncha nha nha n'okpuru isi bolt ma ọ bụ ihe mgbochi serated ga-abanyerịrị n'ihe mkpuchi na-adịghị mma dị ka etiti anodized.
• Akpịrị eriri dabara adaba maka M4 bolt.
• Ngwaike niile ga-abụ nke igwe anaghị agba nchara, igwe anaghị agba nchara 300, ma ọ bụ echekwabara corrosion dabara adaba.
• Ihe akwadoro maka ịgbachi mkpụrụ akụ bụ 2 Nm÷2.2 Nm (1,48÷1,62 ft-lb).
• Ngwunye ala ga-agafe ihe niile ejikọrọ.

• Ngwa ndị edepụtara na nke achọpụtara maka ịkụda okpokolo agba nke modul PV ka enyere ikike ịkwatu okpokolo agba ọla ekpughere nke modul ahụ ka ọ bụrụ ihe mgbakwasị ụkwụ.
• In any case the grounding screws or other parts have to be used separately from the mounting parts of the module.
• Alternate grounding options built through the mounting system are acceptable as long as they have been IEC and UL approved.
• Grounding resistance of the grounding structure shall be reached according to local regulations, Eurocodes, or other legal normative references.

Frameless type modules grounding

• Due to that modules are without frame, grounding is not forseen. Other PV plant equipment should be grounded according to the local and national electrical codes.

NKỌTA

• Connectors for SoliTek PV panels are Stäubli MC4-Evo 2. Keep connectors dry and clean and ensure that connector caps are hand-tight before connecting the modules.
• Anwala ime njikọ eletrik na njikọ mmiri mmiri, nke ruru ala ma ọ bụ nke na-adịghị mma.
• Zere ikpughe ìhè anyanwụ na imikpu mmiri nke njikọ. Zere njikọ na-ezu ike n'ala ma ọ bụ elu ụlọ.
• Do not disconnect under load. Faulty connections can result in arcs and electrical shock.
• Lelee na etinyere njikọ eletrik niile nke ọma. Gbaa mbọ hụ na njikọ niile akpọchiri akpọchi na akpọchi.

BYPASS DIODS

The PV module’s junction box contains 3 bypass diodes (one in each part of split junction box; Schottky type) connected in parallel with the PV cell strings. In the case of partial shading (hot-spot effect), the diodes bypass the current generated by the non-shaded cells, therebylimiting module heating and performance losses.
Diodes ngafe abụghị ngwaọrụ nchebe karịrị akarị. Diodes na-agafe agafe na-atụgharị ugbu a site na eriri cell ma ọ bụrụ na e nwere ndò nke akụkụ. Njirimara nke diodes ndị a:

• Voltage gosiri - 50V.
• Ogo dị ugbu a - 25 A.

Ọkụ Klas RATING

• SoliTek SOLID Bifacial na Blackstar modul akwadoro site na ule ọkụ ọkụ nke IEC wee nweta Flammability Class A. A na-eme ule ọkụ na ọchịchọ nke 127 mm (5 inch) kwa 300 mm (11,81 inch), dị ka edepụtara na isi A.2.5 nke IEC 61730-2.
• SoliTek SOLID Bifacial has fire rating of 28 according to UL1703-2 standard. SoliTek Blackstar has fire rating of 29 according to UL1703-2 standard.

N'ibu arịọnụ

• The mechanical loads described in this manual are the test loads.
• For calculating the equivalent maximum design loads, a safety factor of 1.5 (Design load×1.5 safety factor=Mechanical test load) needs to be considered in compliance with the requirements of the local laws and regulations.

NKWUO GBASARA YA

• Modules can be mounted in landscape or portrait orientation. For the bifacial modules, in order to get notable bifacial gain, the distance between the bottom of the modules and the roof or ground surface shall be at least 0,8 m (31,50 inch).
• Also, the bifacial gain increases significantly if modules are installed above white, light-reflecting surfaces (under surfaces with high albedo value).
• If the mounting rails are installed across the module, the bifaciality effect will be lower due to back-side cells shading.
• Biko debe ụkpụrụ nchekwa yana ntuziaka nrụnye gụnyere yana sistemu ịrịgo. Ọ bụrụ na ọ dị mkpa, biko kpọtụrụ onye na-eweta ngwaahịa ozugbo maka ozi ndị ọzọ.
• The modules must be safely set onto the mounting rail.
• The whole rail supporting the photovoltaic system must be strong enough to resist potential mechanical pressures caused either by wind or snow, in accordance with local, regional and state safety (and other associated) standards.
• The mounting system shall be tested and inspected by a third-party testing institution with static mechanical analysis capacity in accordance with local national standards or international standards.
• Before installing modules on a roof, ensure that the roof construction is suitable.
• In addition, any roof penetration required to mount the modules must be properly sealed to prevent leaks.
• Jide n'aka na ụgbọ okporo ígwè na-arị elu agaghị emebi ma ọ bụ na-emetụta modul mgbe ọ gbasaa n'ihi mgbasawanye ọkụ.
• The module can appear thermal expansion and cold contraction; thus, the interval between two adjoining modules shall be no lesser than 10 mm (0,39 inch).
• Anwala ịkụnye oghere n'elu iko na okpokolo agba nke modul n'ihi na nke a ga-emebi akwụkwọ ikike.
• The mounting method must not result in the direct contact of dissimilar metals with the aluminum frame of the modules that will result in galvanic corrosion.

Ekwesịrị iji ihe na-adịgide adịgide, ihe mgbochi na-eguzogide ọgwụ na UV (a na-atụ aro igwe anaghị agba nchara na aluminom anodized).

NA-ebuli elu na CLAMPS

• Jiri opekempe 4 laminate clamps iji dozie modul na okporo ígwè na-arị elu. Modul clamps metal akụkụ ekwesịghị ịbanye na kọntaktị na ihu ma ọ bụ azụ enyo. Mgbe ị na-ahọrọ ụdị clamp-nrịgoro usoro, jiri opekata mpe anọ clamps na nke ọ bụla modul; abụọ clamps kwesịrị itinye n'akụkụ ogologo ọ bụla. Dabere na ikuku mpaghara na ibu snow, mgbakwunye clamps nwere ike ịchọrọ iji hụ na modul nwere ike ibu ibu ahụ.
• Clamps tightening torque kwesịrị ịbụ opekata mpe 15 Nm (11,06 ft-lb), mana ọ bụghị ihe karịrị 20 Nm (14,75 ft-lb). Ọtụtụ mgbe, 15 Nm (11,06 ft-lb), ruru mgbe aluminom abụọ profilena-emetụ ibe ha aka. Mgbe etinyere modul na nghazi eserese n'elu ụlọ nke nwere> 45° mkpọda, a ga-achọ nko ọzọ na ala modul ahụ.

SOLID Black, Semi-clear, Satin, Agro Frameless

Na okporo ụzọ transversal

BLACKSTAR, SOLID Black 35(40) mm, SOLID Semi-clear 35(40) mm, SOLID Satin 35(40) mm, SOLID Agro 35(40) mm, Magnus Framed mounting

• Mgbe ị na-ahọrọ ụdị clamp-nrịgoro usoro, jiri opekata mpe anọ clamps na nke ọ bụla modul; abụọ clamps kwesịrị itinye n'akụkụ ọ bụla nke modul. Modul clamps ekwesịghị ịbịa na kọntaktị na ihu iko ma ghara imebi etiti.
• Jide n'aka na ịzere mmetụta ndò na sel anyanwụ site na modul clamps.
• The module frame is not to be modified under any circumstances. Do not to block the drain hole of the frame.
• Ogologo nke clamp should be at least 30 mm (1,18 inch).
• Ihe clamp ga-emechie etiti modul ma ọ dịkarịa ala 5 mm (0,2 inch), mana ọ bụghị karịa 10mm (0,4 inch).

Na okporo ụzọ transversal

Na-enweghị okporo ụzọ transversal ma ọ bụ ụgbọ okporo ígwè na-adaba na etiti akụkụ ogologo

Na usoro ntinye

Ịkwado na bolts

• A ga-etinyerịrị modul ahụ ma kwado ya site na bolts igwe anaghị agba nchara anọ nke M8 site na oghere mgbago egosipụtara na ogwe transversal. Torque na clamp bolt has to be in range of 8÷10 Nm (5,9÷7,38 ft-lb). The transversal bars positioning is shown in Figure 3.
• If additional mounting points are required, depending on the local wind and snow loads, then a mounting solution with clampEkwesịrị ịhọrọ ngwaike ing.

• Mounting with bolts can be done only through dedicated predrilled holes in the frame.
• Amachibidoro igwu oghere ọhụrụ na ọ ga-emebi akwụkwọ ikike.

POSITION OKWU NKWUKWU

• Maka ebe dị anya n'etiti igbe nkwụsị na nsọtụ modul ma ọ bụ akụkụ ndị ọzọ nke ọnọdụ igbe njikọ na mpaghara biko rụtụ aka na ọnụ ọgụgụ egosiri n'okpuru.

Nkwadebe

• Iji hụ na arụmọrụ modul kachasị mma, SoliTek na-akwado ihe ndị a:
• Ọ bụrụ na ọ dị mkpa, enwere ike ihicha iko n'ihu modul ahụ na mmiri na sponge dị nro ma ọ bụ akwa akwa.
• Enwere ike iji ncha dị nro, nke na-adịghị emebi emebi, wepụ ntụpọ ndị isi ike karịa.
• Lelee njikọ eletriki na ígwè ọrụ kwa oge wee hụ na ha dị ọcha, nchekwa, zuru oke na nchekwa.
• Ọ bụrụ na enwere nsogbu, kpọtụrụ onye nwere ikikere/onye ruru eru.

Nkọwapụta

Table 9. Electrical and mechanical parameters table.

Table 10. Electrical and mechanical parameters table.

Table 11.Electrical and mechanical parameters table.

• The electrical characteristics are within of the indicated values of ISC (φISC) ±3%, VOC (ϕVOC) ±3,5% and PMPP (ϕPmax) ±5%, under Standard Test Conditions (STC) (irradiance of 1000 W/m²,AM 1.5 spectrum, and a cell temperature of 25°C / 77°F)
• Ihe niile SoliTek SOLID PV dakọtara na klaasị nchekwa eletriki II.

Disclaimer nke ibu

• Ebe ọ bụ na ọ gaghị ekwe omume SoliTek ijikwa nrụnye, ịrụ ọrụ, ngwa na nhazi nke usoro fotovoltaic dịka ntụziaka a si dị. SoliTek anaghị anabata ọrụ ma kwupụta ụgwọ ọrụ maka mfu, mmebi ma ọ bụ mmefu ọ bụla sitere na ma ọ bụ n'ụzọ ọ bụla jikọtara ya na nrụnye, ọrụ, ojiji ma ọ bụ mmezi.
• SoliTek will not take any responsibility for any possible violation of patent rights and third-party rights that are related to the application of the solar energy system. No permission of patents is given through implication.
• The information of this instruction is from the knowledge and experiences of SoliTek. However, the instructions and suggestions of this instruction do not make an external or internal of guarantee. SoliTek reserves the right to revise this instruction, products and all the information about products without prior notification to customers.

www.solitek.eu

FAQ

• Q: What should I do before installing the PV modules?
  • A: Read this entire guide, understand all instructions, and ensure compliance with all local, state, and federal regulations. Consult a certified building specialist for the structural integrity of the dwelling.
• Q: Can I install the PV modules myself without professional training?
  • A: This documentation is not a complete installation manual for personnel not specifically trained in PV-modules. It serves as a general but strictly mandatory reference for the installer. Professional installation is highly recommended.
• Q: What happens if I don’t follow the instructions in this guide?
  • A: Failure to follow instructions may damage system components, endanger personnel, damage property, or invalidate the panel warranty.
• Q: Is it safe to work on a rooftop during installation?
  • A: Do not attempt to work on a rooftop until safety precautions have been identified and taken, including fall protection measures, ladders or stairways, and personal protective equipment (PPE). Avoid adverse conditions like strong winds or wet/frosted roofs.
• Q: How should I store the PV modules before installation?
  • A: Store pallets in a cool and dry location until the PV modules are ready to be unpackaged. Do not exceed the maximum stacking height indicated on the packaging.