XP-8v
Advanced Control Processor
Ntuziaka ntụaka

XP-8v Advanced Control Processor

The XP-8v is a high-end remote control processor for automating the operation of electronic systems in homes and office buildings. The combination of a blazing fast MPU, real-time/multitasking operating system, and tremendous expansion capability, make the XP-8v the perfect solution for large-scale and complex projects.
The XP-8v provides superior quality and reliability as well as these features:

• Powerful 1GHz internal processor.
• 1GB of RAM memory and 512MB of non-volatile flash memory built in.
• SD/MM card slot allows memory expansion.
• Eight multi-purpose I/O ports.
• Eight programmable relay outputs.
• Eight two-way RS-232 ports.
• Eight sense inputs.
• Multi-purpose I/O ports are compatible with industry-standard IR emitters, blasters and repeater systems.
• Multi-purpose I/O ports support all optional RTI power sensing and communications modules.
• All output ports incorporate both short-circuit and overload protection.
• Mbupute IR na-agbanwe agbanwe na ọdụ ụgbọ mmiri niile.
• Front panel controls/display (11 Buttons for front panel control).
• Non-volatile Flash memory stores your system configuration even when power is not present.
• Field upgradeable firmware.
• USB and Ethernet programming.
• Compatible with RTI 433MHz and 2.4GHz Zigbee RF modules.
• Astronomical clock built in for time-based event programming.
• Designed for rack mount or free standing installations.

Nwụnye & Ọrụ

PROGRAMMING THE XP-8v
The XP-8v must be programmed to operate. All programming is done using RTI’s Integration Designer software and is downloaded using the USB ® Programming Port located on front of XP-8v or via Ethernet.
IHE EMERE FIRMWARE
A na-atụ aro nke ukwuu na nke a na ngwaahịa RTI niile arụnyere ngwa ngwa kachasị ọhụrụ. Enwere ike ịchọta ngwa ngwa na ngalaba Dealer nke RTI websaịtị (www.rticontrol.com). Install the firmware using the USB Programming Port located on the front of XP-8v.
MPIO PORTS – Control via Infrared, Sensing and RS-232 (One-way)

INFRARED EMITTERS
The multi-purpose I/O ports on the XP-8v are compatible with industry standard infrared emitters and infrared repeating systems. Each output port is capable of driving up to four infrared emitters directly. The use of more than four infrared emitters requires the addition of an amplified connecting block. A connecting block can be wired up to 1000 feet away from the XP-8v using #22 AWG (minimum) wire.
INFRARED OUTPUT GAIN ADJUSTMENT
The IR output gain can be separately adjusted for each of the eight output ports. The XP-8v is shipped with the IR gain set to the optimum level for most equipment, and it should only need to be adjusted if the attached equipment is not responding reliably. If adjustment is needed, rotate the IR output controls on the front of the XP-8v clockwise for higher output power, or counter-clockwise for lower output power.
IHE: The IR output feedback LEDs located on the front of the XP-8v will illuminate when any IR code is delivered out of a port. This includes IR codes “passing through” from another source, such as an IR receiver.
VPS-1 SENSOR MODULE
The multi-purpose I/O ports on the XP-8v are compatible with RTI power sensing modules (e.g. VPS-1). Follow the guide included with the modules for installation instructions, and follow the instructions in the Integration Designers software for programming details.
RS-232 COMMUNICATION MODULES (CM-232)
The multi-purpose I/O ports on the XP-8v are compatible with RTI RS-232 communication modules (e.g. CM-232). Follow the guide included with the modules for installation instructions, and follow the instructions in the Integration Designer software for programming details.
RS-232 PORTS

The XP-8v is capable of two-way control using RS-232 communication via eight RJ-45 output ports using standard Cat-5/6 cable with RJ-45 termination (568B). The XP-8v ships with eight RJ-45 (female) to DB-9 (male) adapters.
IMPORTANT NOTE: RS-232 communication cabling should be limited to 50 feet (16m) depending on baud rate.
DB-9-RJ45 ADAPTOR PINOUT
RJ-45 (XP-8v RS-232 Output)

Ntụtụ	Aha mgbaàmà	Nkọwa mgbaàmà
1	DSR	Data Njikere
2	DCD	Chọpụta ihe ụgbọelu
3	DTR	Njikere ọdụ data
4	GND	Signal Ground/Common
5	RXD	Nweta data
6	TXD	Nyefee data
7	CTS	Kpochapụ izipu
8	RTS	Arịrịọ izipu

DB-9

Ntụtụ	Aha mgbaàmà	Nkọwa mgbaàmà
1	DCD	Chọpụta ihe ụgbọelu
2	RXD	Nweta data
3	TXD	Nyefee data
4	DTR	Njikere ọdụ data
5	GND	Ala mgbaàmà
6	DSR	Data Njikere
7	RTS	Arịrịọ izipu
8	CTS	Kpochapụ izipu
9	NC	Ejikọtaghị ya

SENSE INPUTS / RELAY-TRIGGER OUTPUTS
Sense inputs and relay-trigger modes are configured within Integration Designer ® .

SENSE INPUT
Upon sensing contact closure or a voltage (2-24VDC), events can be automatically triggered such as a macro or command.
Sense contact closure: Connect conductors from the source device to each side of a sense input (A and B).
Sense voltage mkpata: Connect positive lead from voltage source to Side A of sense input and ground lead to Side B.
RELAYS/TRIGGER OUTPUTS
Relays may be configured as a dry contact closure or a voltage trigger output (12VDC @100mA). All relays are Normally Open when not energized, and may be programmed to behave Normally Closed (as long as power is applied to the XP-8v).
Mmechi kọntaktị: Connect the A and B contact terminals of a relay to the device.
Voltage trigger: Connect contact A to the positive lead and connect Contact B to the ground lead of the device.

Ọ nọ n'okpuru njikwa ®

SIGNAL IN/HIGH OUT/POWER TERMINALS

TERMINAL: +12VDC
Positive power supply connection. It is internally tied to the Power jack. This can be used to power external IR or RF receivers.
TERMINAL: GROUND
Common ground connection. Use this ground reference for any device that is connected to the +12VDC, SIGNAL IN, OR HIGH OUT terminals.
TERMINAL: INPUT
Input connection for system trigger codes. This should be connected to an RTI RM433 RF receiver
or industry standard IR repeater system. The signal voltage can be from 3VDC – 12VDC.
TERMINAL: HIGH OUT
High current (200mA) IR output connection. This can be used to power up to 10 infrared mini-emitters, an IR blaster, or extending IR control over a long distance (1000 ft. max).
ETHERNET, USB, RTI COM, EXPANSION PORT

EtherNET
This RJ-45 port allows connection to a 10/100 Base-T Ethernet network (LAN).
Network settings such as the IP address are configurable within Integration Designer®.
Ethernet may also be used to download system files to the XP-8v.
USB PORTS (REAR)
These host ports for external devices are intended for future use.
RTI COM
This RJ-45 port allows connection to a ZM-24 Zigbee transceiver module for two-way communication with compatible RTI handheld controllers. Refer to the ZM-24 Zigbee transceiver module operation guide for installation instructions.
Ọdụ ụgbọ mmiri Mgbasawanye
This RJ-45 port provides a convenient connection for receiving IR signals and two-way RS-485 communication from RTI in-wall controls through a CB-8 connecting block. NOTE: In-wall controllers may be connected directly to the XP-8v Expansion Port, however, they should be powered with a separate power supply.
IKE

ỊNYE ỌKỤ
To power the XP-8v, use the supplied 12VDC/1Amp ịnye ọkụ.
XP-8v Front

 

Ngosipụta NKWUO
The display on the XP-8v is designed to give the installer feedback on the current status of the XP-8v, change settings such as the time/date and offer some basic diagnostic tools for troubleshooting. See XP-8v Display Technical Bulletin for detailed display menu options.
IHE
Any configuration changes made through the XP-8v display settings will be overwritten after the XP-8v is rebooted or an RTI system file is downloaded into the XP-8v memory.
FRONT PANEL LOCKOUT
It is possible to set a passcode that will block access to the menu system on the XP-8v. This can be set in the properties of the XP-8v within the RTI Integration Designer® programming software and downloaded as part of the system file. Use the cursor buttons on the XP-8v to enter the correct passcode to open the menu display.
NA-ebugo
The XP-8v ships with four removable feet that allow the unit to be placed on a flat surface. The XP-8v can also be mounted in a component rack as part of a comprehensive control system. Remove feet before mounting in a rack.

Ọdịnaya ngwaahịa

• One (1) XP-8v Advanced Control Processor
• One (1) Power supply (12V, 1A)
• Eight (8) RJ45 to DB9 serial adaptors
• Two (2) Rack ears (2) with screws (8)
• Three (3) Terminal blocks (2 x 16-position, 1 x 4-position)
• One (1) Reference guide
• One (1) MAC address card

Aro maka nchekwa

Read and Follow Instructions. Read all safety and operating instructions before operating the unit.
Retain Instructions. Keep the safety and operating instructions for future reference.
Heed Warnings. Adhere to all warnings on the unit and in the operating instructions.
Heat. Keep the unit away from heat sources such as radiators, heat registers, stoves, etc., including amplifiers na -emepụta okpomọkụ.
Power Sources. Connect the unit only to a power supply of the type described in the operating instructions, or as marked on the unit.
Power Cord Protection. Route power supply cords so that they are not likely to be walked on or pinched by items placed on or against them, paying particular attention to the cord plugs at power receptacles and at the point at which they exit from the unit.
Water and Moisture. Do not use the unit near water—for example, nso a sink, na a mmiri mmiri okpuru ulo, nso a igwu mmiri, nso na windo mepere emepe, wdg.
Object and Liquid Entry. Do not allow objects to fall or liquids to be spilled into the enclosure through openings.
Servicing. Do not attempt any service beyond that described in the operating instructions. Refer all other service needs to qualified service personnel.
Damage Requiring Service. The unit should be serviced by qualified service personnel when:

• Ebibiela eriri ọkụ ọkụ ma ọ bụ plọg.
• Ihe adaala ma ọ bụ mmiri awụfuwo na nkeji.
• Igwe ahụ ekpuchila mmiri ozuzo.
• Ngalaba ahụ apụtaghị na ọ na-arụ ọrụ nke ọma ma ọ bụ gosipụta mgbanwe pụtara ìhè na arụmọrụ.
• Awụpụla otu ahụ ma ọ bụ mebie ihe mgbochi ahụ.

Nhicha

To clean your XP8v, lightly dampna akwa na-enweghị lint na mmiri dị larịị ma ọ bụ ncha dị nro ma hichaa elu elu.
IHE: Ejila kemịkalụ siri ike n'ihi na mmebi nke unit nwere ike ime.
Akwụkwọ ọkwa Federal Communications Commission
A nwalere ngwa a wee hụ na ọ dabara na oke maka ngwaọrụ dijitalụ Klas B, dabere na akụkụ 15 nke Iwu FCC. Emebere oke ndị a iji nye nchebe ezi uche dị na ya megide nnyonye anya na-emerụ emerụ na ntinye ụlọ. Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị otu na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ọrụ ahụ.
Akụrụngwa a na-ewepụta, na-eji, ma nwee ike ịgbasa ike ugboro redio yana, ọ bụrụ na etinyeghị ya ma jiri ya dịka ntuziaka siri dị, nwere ike ibute ndabichi na-emerụ ahụ na nkwukọrịta redio. Agbanyeghị, enweghị nkwa na nnyonye anya agaghị eme na otu nrụnye.
Ọ bụrụ na akụrụngwa a na-ebute nnyonye anya na-emerụ ahụ na nnabata redio ma ọ bụ telivishọn, nke enwere ike ikpebi site na ịgbanyụ ma gbanye akụrụngwa, a na-agba onye ọrụ ume ka ọ nwaa idozi nnyonye anya site na otu ma ọ bụ karịa n'ime usoro ndị a:

• Megharịa ma ọ bụ bugharịa antenna nnata.
• Mee ka nkewa dị n'etiti akụrụngwa na onye nnata.
• Jikọọ akụrụngwa n'ime oghere na sekit dị iche na nke ejikọrọ onye nnata.
• Kpọtụrụ onye na-ere ahịa ma ọ bụ onye ọrụ redio/TV nwere ahụmahụ maka enyemaka.

Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:

1. Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ.
2. Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.

Nkwupụta nnabata ụlọ ọrụ Canada
Ngwaọrụ a na-akwado ụkpụrụ (s) RSS enweghị ikike ụlọ ọrụ Canada. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:

1. Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ.
2. Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.

Kpọtụrụ RTI
Maka ozi gbasara mmelite kachasị ọhụrụ, ozi ngwaahịa ọhụrụ na ngwa ọhụrụ, biko gaa na nke anyị web saịtị na: www.rticontrol.com
Maka ozi izugbe, ị nwere ike ịkpọtụrụ RTI na:
Remote Teknụzụ Incorporated
5775 12th Ave. E Suite 180
Shakopee, MN 55379
Tel. 952-253-3100
info@rticontrol.com

Ọrụ & Nkwado

Ọ bụrụ na ị na-ezute nsogbu ọ bụla ma ọ bụ nwee ajụjụ gbasara ngwaahịa RTI gị, biko kpọtụrụ Nkwado nka na ụzụ RTI maka enyemaka (lee ngalaba ịkpọtụrụ RTI nke ntuziaka a maka nkọwa kọntaktị).
RTI na-enye nkwado teknụzụ site na ekwentị ma ọ bụ ozi-e. Maka ọrụ kacha mma, biko jikere ozi ndị a:

• Aha gị
• Aha Ụlọ Ọrụ
• Nọmba ekwentị
• Adreesị ozi ịntanetị
• Ụdị ngwaahịa na nọmba nsonazụ (ọ bụrụ na ọdabara)

Ọ bụrụ na ị na-enwe nsogbu na ngwaike, biko rịba ama akụrụngwa dị na sistemụ gị, nkọwa nke nsogbu ahụ, yana nchọpụta nsogbu ọ bụla ị nwalarị.
*Biko eweghachila ngwaahịa na RTI na-enweghị ikike nloghachi.*

Akwụkwọ ikike nwere oke

RTI na-akwado ngwaahịa ọhụrụ maka afọ atọ (3) (ewezuga ihe oriri dị ka batrị enwere ike ịchaji nke enyere ikike maka otu afọ) site na ụbọchị nke onye zụrụ azụ (onye ọrụ njedebe) ozugbo site na RTI / Pro Control (1). ebe a na-ezo aka dị ka “RTI”), ma ọ bụ onye na-ere ahịa RTI ikike.
Warranty claims may be initiated by an authorized RTI dealer using the original dated sales receipt or other proof of warranty coverage. In the absence of the receipt of purchase from the original dealer, RTI will provide warranty coverage extension of six (6) months from the date code of the product.
Mara: RTI warranty is limited to the provisions set forth in this policy and does not preclude any other warranties offered by third parties who are solely responsible for those other warranties.
Ewezuga dị ka akọwapụtara n'okpuru, akwụkwọ ikike a na-ekpuchi ntụpọ dị na ngwa ngwaahịa na arụ ọrụ. Akwụkwọ ikike ekpuchighị ihe ndị a:

• A gaghị enye ngwaahịa a zụtara site na ndị na-ere ihe na-akwadoghị ma ọ bụ saịtị ịntanetị - n'agbanyeghị ụbọchị ịzụrụ.
• Mmebi ndị sitere na ihe mberede, ojiji, mmegbu, nleghara anya ma ọ bụ omume nke Chineke kpatara.
• Mmebi ihe ịchọ mma, gụnyere, mana ọnweghị oke na, ncha, ncha na iyi akwa na akwa nkịtị.
• Ọdịda iso ntuziaka dị na ntuziaka nwụnye ngwaahịa.
• Mmebi n'ihi ngwaahịa a na-eji na ngwa ma ọ bụ gburugburu ebe ọzọ na-abụghị nke e zubere ya, usoro ntinye na-ezighị ezi ma ọ bụ ihe ọjọọ gburugburu ebe obibi dị ka ahịrị na-ezighi ezi vol.tages, wiwi na-ezighi ezi, ma ọ bụ ikuku ikuku na-ezughị oke.
• Mekwaa ma ọ bụ nwara ịrụzi nke onye ọ bụla na-abụghị RTI na Pro Control ma ọ bụ ndị mmekọ ọrụ ikike.
• Ọdịda n'ịrụ nlekọta oge akwadoro.
• Ihe kpatara ndị ọzọ karịa ntụpọ ngwaahịa, gụnyere enweghị nka, ikike ma ọ bụ ahụmịhe nke onye ọrụ.
• Mmebi n'ihi mbupu ngwaahịa a (a ga-emerịrị onye na-ebu ya ebubo).
• Otu agbanwere ma ọ bụ nọmba nsonazụ gbanwetụrụ: emebiela, gbanwee ma ọ bụ wepụ.

Ejikwaghị RTI maka:

• Mmebi nke ngwaahịa ya kpatara ma ọ bụ maka ọdịda nke ngwaahịa ya ịrụ, gụnyere ụgwọ ọrụ ọ bụla, uru furu efu, nchekwa furu efu, mmebi mberede, ma ọ bụ mmebi ga-esi na ya pụta.
• Mmebi dabere na ọdịmma, mfu nke ngwaahịa ahụ, ọnwụ oge, ọrụ kwụsịrị, mfu azụmahịa, nkwuputa ọ bụla nke onye ọzọ kwuru ma ọ bụ mere n'aha ndị ọzọ.
• Ọnwụ, ma ọ bụ mebie, data, sistemụ kọmputa ma ọ bụ mmemme kọmputa.

RTI’s liability for any defective product is limited to repair or replacement of the product, at the sole discretion of RTI.
In cases where the warranty policy conflicts with local laws, the local laws will be adopted.

Nkwuwapụta nke ndabara (DOC)
Enwere ike ịchọta nkwupụta nkwenye maka ngwaahịa a na RTI websaịtị na: www.rticontrol.com/declaration-of-conformity

Nwebiisinka © 2025
Remote Teknụzụ Incorporated
Ikike niile echekwabara.

Akwụkwọ / akụrụngwa

RTI XP-8v Advanced Control Processor [pdf] Ntuziaka onye ọrụ XP-8v Advanced Control Processor, XP-8v, Advanced Control Processor, Control Processor, Processor

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ