Qoltec 52484 Digital Battery Tester with LCD Display
Akwụkwọ ntuziaka USER
Nlereanya: 52484
Display | 12V | 24V | 3Ah-200Ah
Okwu mmalite
Thank you for your trust and for choosing our battery tester. We are confident that the product will meet your expectations.
This manual will guide you through the installation and use of the device. If you have any questions after reading this manual, please contact the NTEC sp. z o.o. service department.
Ozi ngwaahịa
Using the most advanced conductivity testing technology and reverse polarity protection, the 12V-24V battery tester provides critical information about the condition of the battery under test to quickly diagnose battery and charging problems.
NKWUKWU
The battery type and CCA (cold starting current) values are indicated on the battery label, please refer to them before use. The tester supports the following battery types :
VRLA, GEL, AGM, EFB, STD.
Ntuziaka maka iji echekwabara
1. This tester must be used in accordance with the instructions, taking into account the working conditions and the type of work to be performed. Use of the tester in a manner inconsistent with its intended use may result in dangerous situations.
2. Ensure that the battery terminals are clean before testing, as grease and dust can lead to errors in the test results.
3. Wear safety goggles when working near batteries.
4. To avoid electric shock, check that the insulation layer of the battery terminals is in normal condition (not damaged, bare or disconnected).
5. The test should be carried out in a well-ventilated area. Explosive and toxic gases may be produced during testing.
6. Keep hair, hands and clothing, as well as the tester cables, away from moving blades and belts.
7. Do not store the tester in a place accessible to children.
8. Do not place the tester near the engine or exhaust pipe to avoid damage from high temperatures when the car engine is running.
9. Aṅụla sịga, kpalite ma ọ bụ jiri ọkụ n'akụkụ batrị n'oge ule.
10. Ewepụla ọnụ batrị n'oge ule.
11. To avoid damage to the tester, do not place it in a damp ma ọ bụ gburugburu uzuzu.
12. Do not disassemble the tester as this may damage it.
Nkọwa ngwaọrụ
Ihe atụ nke 1 na mgbakwunye
| Mba | Ọrụ | ||||
| 1 | Previous option / increase in battery rating | ||||
| 2 | Kagbuo | ||||
| 3 | Next option / decrease battery rating | ||||
| 4 | Kwenye | ||||
| 5 | Tọgharịa / Malitegharịa ekwentị | ||||
| 6 | Red “Crocodile” type terminal : Positive battery test terminal | ||||
| 7 | Black crocodile-type terminal : Negative battery test terminal | ||||
HOW TO START THE TESTER ?
The tester will check each battery according to the actual system standard selected and the parameters marked on the battery to obtain an accurate result.
Tupu ule
The engine and all other power sources must be OFF during the test for accurate results. Turn on the vehicle’s headlights for 2-3 minutes until the battery voltage drops to a normal value if the battery is fully charged.
Nzọụkwụ 2
a. The red positive (+) battery terminal is connected to the positive (+) battery terminal and the black negative (-) battery terminal is connected to the negative (-) battery terminal. Ensure that the clamps nwere njide siri ike na ọdụ batrị maka nsonaazụ ziri ezi.
b. Pịa 
or 
to select the BATTERY TYPE ( is specified on the battery nameplate), confirm with “ENTER”.
Ihe atụ 2
c. ihe Pịa or to select the corresponding test standard ( is indicated on the battery nameplate), again confirm with “ENTER”.
Onyonyo 3
d. Hold down or and then select the battery’s EDC/CCA values ( is specified on the battery nameplate or in the EDC/CCA parameter table).
Ihe atụ 4
EDC/CCA Parameter table
Ihe atụ 5
e. Press “ENTER” to start the battery test.
Ihe atụ 6
f. The test results are as follows:
Ihe atụ 7
SOH: Ọnọdụ
R: Nguzogide n'ime
Onyonyo 8
SOC: Ọnọdụ ụgwọ
VOLT: batrị voltage
Onyonyo 9
EDC/CCA: Atụtara mwepu ugbu a
FINAL TEST RATING
| Zuru oke | Ideal battery life, SOH ≥ 90% | |||
| ỌMA | Battery life Good, SOH ≥ 75% | |||
| ỌJỌỌ | Bad Battery life, SOH ≥ 50% | |||
| Dochie | Battery dead, SOH < 50% | |||
| MKWUO | Nwalee batrị ọzọ mgbe ịchachara | |||
| The terminal is not well connected to the battery terminal batrị |
||||
BATTERY SYSTEM SPECIFICATION
Onye nlebanya batrị ga-anwale batrị ọ bụla dabere na usoro ahọpụtara na ogo.
| CCA: | Mmalite oyi amps, specified by SAE and BCI, the most commonly used value for starting the battery at(-18’C) | ||||
| IEC: | Standard of the internal electrotechnical commission | ||||
| SAE: | Standard of the Society of Automotive Engineers | ||||
| EN: | Standard of the European Automobile Industry Njikọ |
||||
| DIN: | Standard of the German Automobile Industry Committee | ||||
| CA: | Malite amperes Standard effective starting current at 0°C | ||||
Nkọwapụta ngwaahịa
Ngosipụta: 2.7 ″ LCD
Cable range: 650 mm
Storage temperature: -20° C to +70 C °
Operating temperature: -20° C to +60 C °
Akụkụ: 150x90x35 mm
Net weight : 325 g
Iji
1. Dispose of according to local electronic waste regulations.
2. Do not dispose of in fire or incinerate.
NKWUKWU
Product covered by a 24 month manufacturer’s warranty from the date of purchase. In case of problems, please contact customer service.
Mgbakwunye
Nkọwapụta
- Ụdị: 52484
- Voltage Compatibility: 12V – 24V
- Battery Capacity Range: 3Ah – 200Ah
- Supported Battery Types: VRLA, GEL, AGM, EFB, STD
Ajụjụ A na-ajụkarị (FAQ)
Q: Can I use the tester for other types of batteries not listed?
A: The tester is designed for specific battery types mentioned in the compatibility section. Using it with other types may not provide accurate results.
Q: Is this battery tester powered by internal batteries?
A: No, the tester can only be powered by the battery under test.
Q: Can the tester charge the battery?
A: The tester can detect the battery, check its condition, but will not charge the battery.
Q: Can the Tester check the life of the battery?
A: Yes, we can check the state of the battery and the percentage nke ugwo.
Q: Which batteries can the tester be used with?
A: It can be used with 12V and 24V batteries.
Q: Why is the test result inaccurate?
The parameter set may be incorrect. Enter the correct data from the battery label.
Q: Why does the display show nothing?
A: Gbaa mbọ hụ na batrị voltage is higher than 8V and the terminals are connected correctly.
Akwụkwọ / akụrụngwa
 |
Qoltec 52484 Digital Battery Tester with LCD Display [pdf] Akwụkwọ ntuziaka onye ọrụ 52484 Digital Battery Tester with LCD Display, 52484, Digital Battery Tester with LCD Display, Battery Tester with LCD Display, Tester with LCD Display, LCD Display, Display, Tester |
