Omada L3 Campus Stackable Managed Switch User Manual

L3Campus Stackable Managed Switch

Nkọwapụta

Model: Omada Campus Stackable L3 Managed Switch
Front Panel: Mode Selection Button, Management Port, LED,
Console Port USB2.0 Port (Type-C/RJ45), 1G RJ45 Port, 10G SFP+ Slot
Ikanam
Ngosipụta LED:
- PWR1*: Green On (switch powered by PWR1), Off (PWR2
  disconnected or not working properly)
- PWR2: Green On (switch powered by PWR1 and PWR2 connected),
  Yellow On** (PWR2 powered), Off (PWR1 disconnected or not working
  nke ọma)
- LED SYS FAN: Green On (all fans work properly), Yellow On (not
  all fans work properly)
- MGMT: On (device linked to port), Flashing (transmitting or
  receiving data), Off (no device linked to port)
- MST: On (device linked to port), Flashing (transmitting or
  receiving data), Off (no device linked to port)

Ntuziaka ojiji ngwaahịa

Isi nke 2: Nwụnye

Tupu ịmalite usoro nwụnye, hụ na ị nwere ihe niile
the necessary tools and follow safety precautions.

Ọdịnaya ngwugwu: Check all items mentioned in
ngwugwu.
Akpachara anya maka nchekwa: Follow the guidelines to
hụ na echichi dị mma.
Ngwa nwụnye: Gather all tools required
maka echichi.
Nwụnye ngwaahịa: Soro nzọụkwụ-site-nzọụkwụ
instructions provided in the manual for successful
echichi.

Nkeji 3: Connection

After installation, connect the switch to the network using
appropriate cables and ports as per your network setup.

Isi nke 4: Nhazi

Configure the switch based on your requirements. You can choose
between Standalone Mode or Controller Mode as per your network
mkpa.

FAQ

Q: What should I do if the LED indications show an error?

A: If the LED indications suggest improper functioning, check
the power sources and connections. Refer to the troubleshooting
ngalaba na ntuziaka maka enyemaka ọzọ.

Business ịkparịta ụka n'Solntanet Ngwọta
Ntuziaka nwụnye
Omada Campus Stackable L3 Managed Switch

Banyere ntuziaka nwụnye a
Ntuziaka nwụnye a na-akọwa njirimara ngwaike, ụzọ nrụnye na isi ihe a ga-agarịrị n'oge nrụnye. A haziri ntuziaka nwụnye a dị ka ndị a: Isi nke 1 Okwu Mmalite Isiakwụkwọ a na-akọwa ihe ndị dị na mpụga nke mgba ọkụ. Isi nke 2 Nwụnye Isiakwụkwọ a na-egosi otu esi etinye mgba ọkụ. Isi nke 3 Njikọ Isi nke a na-egosi otu esi eme njikọ anụ ahụ nke mgba ọkụ. Isi nke 4 Nhazi nke isiakwụkwọ a na-akọwa otu esi ahazi mgba ọkụ. Ihe Mgbakwunye A Nchọpụta nsogbu Mgbakwunye B nkọwapụta

Ndị na-ege ntị

Ntuziaka nwụnye a bụ maka:

Injinia netwọkụ

Onye nchịkwa netwọk

Mgbakọ
Ụfọdụ ụdị egosipụtara na ntuziaka a nwere ike ọ gaghị adị na obodo ma ọ bụ mpaghara gị. Maka ozi ịre ahịa mpaghara, gaa na https://www.omadanetworks.com/.
Ọnụọgụ ndị dị n'Isi nke 2, Isi nke 3, na Isi nke 4 bụ maka naanị ihe ngosi. Mgbanwe gị nwere ike ịdị iche na nke ahụ egosiri.
· Mgbakọ mmefu ego nke PoE dabere na nyocha ụlọ nyocha. A naghị ekwe nkwa mmefu ego ike PoE na ọ ga-adịgasị iche n'ihi oke ndị ahịa na ihe gburugburu ebe obibi.
· Ntuziaka a na-eji usoro a kapịrị ọnụ iji gosipụta ozi pụrụ iche. Tebụl na-esonụ na-edepụta akara ngosi ngosi ndị a na-eji n'oge ntuziaka a.

Chetara ka ị kpachara anya. A ịkpachara anya na-egosi a nwere nke nwere ike ịkpata ngwaọrụ mmebi.
Chetara ka ị rịba ama. Ihe edeturu ahụ nwere ozi na -enye aka maka iji ngwaahịa a ka mma.

Njikọ Akwụkwọ
Enyere ntuziaka onye ọrụ na ntuziaka ntụnye aka CLI nke ngwaahịa a na ebe nbudata. Iji nweta ozi ngwaahịa kacha ọhụrụ, gaa na nke onye ọrụ gọọmentị websaịtị: https://support.omadanetworks.com/document/.

ọdịnaya
Isi nke 1 Okwu Mmalite ———————- 01
1.1 Ngwaahịa gafereview …………………………………………………………………………………..01 1.2 Mpụta………………………………………………………………………………………………………………………………….01
Isi nke 2 nwụnye ———————- 12
Ihe ngwungwu 2.1 ...............................................................................................................................12 2.2 12 2.3 14 2.4 14 ........................................ ...XNUMX
Isi nke 3 Njikọ ———————- 22
3.1 Ethernet Port …………………………………………………………..22 3.2 10G SFP+/25G SFP28/100G QSFP28 Slot ………..22 3.3 Console Port ……………………………………………………………22 3.4 Verify Installation…………………………………………………….23 3.5 Power On ………………………………………………………………….24 3.6 Initialization………………………………………………………………24 3.7 Stack Topology ……………………………………………………….24
Isi nke 4 Nhazi ——————— 27
4.1 Nhazi gafereview……………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………
Ihe mgbakwunye A Nchọpụta nsogbu —————- 32
Ihe mgbakwunye B nkọwapụta —————— 33

Omada Campus Stackable L3 Managed Switch

Isi nke 1 Okwu Mmalite

1.1 Ngwaahịa gafereview
Ezubere maka ụlọ ọrụ na campus, Omada Campus Stackable L3 Managed Switch provides wire-speed performance and abundant L2 and L3 management features. It provides a variety of service features and multiple powerful functions with high security. The EIA-standardized framework and smart configuration capacity can provide flexible solutions for a variable scale of networks. Static Routing, RIP, OSPF, BGP, IS-IS, PIM-SM/DM/SSM, and ECMP come with abundant Layer 3 routing protocols that support a scalable network. Physically stacking for builtin redundancy and performance. Redundant power supplies and fans make it an ideal choice for reliable networking architecture. VRRP allows a group of switches to dynamically back up each other. ERPS supports rapid protection and recovery in a ring topology. MACsec, secure boot, ACL, 802.1x and Dynamic ARP Inspection provide robust security strategies. QoS and IGMP snooping/filtering optimize voice and video application. Link aggregation (LACP) increases aggregated bandwidth, optimizing the transport of business critical data. SNMP, RMON, WEB, Netconf and CLI Log-in bring abundant management policies. These switches integrate multiple functions with excellent performance, and is friendly to manage, which can fully meet the need of the users demanding higher networking performance. S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y is also a Power Sourcing Equipment (PSE*). The RJ45 ports that support Power over Ethernet (PoE*) function can automatically detect and supply power to those powered devices (PDs*) complying with IEEE 802.3af, IEEE 802.3at, and IEEE 802.3bt (only for S6500-24MPP4Y/S6500-48MPP6Y). *PSE: a device (switch or hub for instance) that provides power through an Ethernet cable. *PoE: This technology describes a system to transmit electrical power, along with data, to remote devices over standard twisted-pair cable in an Ethernet. *PD: a device powered by a PSE and thus consumes energy. Examples gụnyere igwefoto netwọk ike, ebe ịnweta LAN ikuku, ekwentị IP, ebe netwọk, kọmputa agbakwunyere wdg.
1.2 Ọdịdị
Front Panel (The figure is for demonstration only. It may differ from your actual product. )
The front panel of S6500-24G4XF is shown as the following figure.
Bọtịnụ nhọrọ ọnọdụ
Port njikwa

Ikanam

Console Port USB2.0 Port (Type-C/RJ45)

Ọdụ ụgbọ mmiri 1G RJ45

10G SFP+ Slot LED

The front panel of S6500-48G6XF is shown as the following figure.
Bọtịnụ nhọrọ ọnọdụ
Port njikwa

Ikanam

Console Port USB2.0 Port (Type-C/RJ45)

Ọdụ ụgbọ mmiri 1G RJ45

10G SFP+ Slot LED

Okwu mmalite 01

Omada Campus Stackable L3 Managed Switch

Ngosipụta LED

PWR1*

NKP2

Green Na

Gbanyụọ

Green Na

Edo Agba**

Gbanyụọ

Green Na

Gbanyụọ

Ngosipụta
PWR1 kwadoro mgba ọkụ ahụ. Akwụpụrụ PWR2 ma ọ bụ ọ na-arụ ọrụ na-ekwesịghị ekwesị.
PWR1 kwadoro mgba ọkụ ahụ. PWR1 na PWR2 jikọọ.*
PWR2 kwadoro mgba ọkụ ahụ. Akwụpụrụ PWR1 ma ọ bụ ọ na-arụ ọrụ na-ekwesịghị ekwesị.
Agbanyụrụ ọkụ ma ọ bụ PWR1 na PWR2 na-arụ ọrụ na-ekwesịghị ekwesị.

LED SYS FAN
MGMT
MST
Port 1-24 of S6500-24G4XF/ Port 1-48 of S6500-48G6XF
(When the SPEED LED is on)
Port 1-24 of S6500-24G4XF/ Port 1-48 of S6500-48G6XF
(Mgbe STK LED na-agbanye)
Port 25-28 of S6500-24G4XF/ Port 49-54 of S6500-48G6XF ***

Ngosipụta
Na-egbuke egbuke: Mgbanwe na-arụ ọrụ nke ọma. Gbanyụọ ma ọ bụ gbanyụọ: Mgbanwe na-arụ ọrụ na-ekwesịghị ekwesị.
Green On: Ndị fan niile na-arụ ọrụ nke ọma. Yellow On: Ọ bụghị ndị Fans niile na-arụ ọrụ nke ọma.
On: A device is linked to the port. Flashing: Transmitting or receiving data. Off: No device is linked to the port.
On: The device functions as the master switch in the stack topology or it works individually. Off: The device functions as the member switch in the stack topology.
Green On: Na-agba ọsọ na 1000 Mbps, mana enweghị ọrụ. Green na-egbuke egbuke: Na-agba ọsọ na 1000 Mbps na-ebufe ma ọ bụ na-anata data. Yellow On: Na-agba ọsọ na 10Mbps/100 Mbps, mana enweghị ọrụ. Ọkụ na-acha odo odo: Na-agba ọsọ na 10Mbps/100 Mbps ma na-ebufe ma ọ bụ na-anata data. Gbanyụọ: Ọ nweghị ngwaọrụ ejikọrọ na ọdụ ụgbọ mmiri kwekọrọ.
Na: Nọmba ọdụ ụgbọ mmiri na-egosi otu ID dị na topology tojupụtara.
Green On: Na-agba ọsọ na 10 Gbps, mana enweghị ọrụ. Green Flashing: Na-agba ọsọ na 10 Gbps ma na-ebufe ma ọ bụ na-anata data. Yellow On: Na-agba ọsọ na 1 Gbps, mana enweghị ọrụ. Ọkụ na-acha odo odo: Na-agba ọsọ na 1 Gbps ma na-ebufe ma ọ bụ na-anata data. Gbanyụọ: Ọ nweghị ngwaọrụ ejikọrọ na ọdụ ụgbọ mmiri kwekọrọ.

*PWR1 is the primary power supply and it takes priority over PWR2. When the device is powered by PWR1, PWR2 will be working in the backup mode.
** Mgbe ma PWR1 na PWR2 na-arụ ọrụ nke ọma na PWR1 na-agbanye mgba ọkụ, ọ na-ewe 10-20 sekọnd maka LED PWR2 (edo edo) ịpụ mgbe PWR2 kwụsịrị.
***All 10 Gbps SFP+ slots can be used as uplink ports or stacking ports. When used as stacking ports, the slots need to run at the highest speed.

02 Okwu mmalite

Omada Campus Stackable L3 Managed Switch The front panel of S6500-24GP4XF is shown as the following figure.

Bọtịnụ nhọrọ ọnọdụ
Port njikwa
LED Console Port USB2.0 Port (Type-C/RJ45)

Ọdụ ụgbọ mmiri 1G RJ45

10G SFP+ Slot LED

E gosiri n'ihu panel nke S6500-48GP6XF dị ka ndị na-esonụ ọnụ ọgụgụ.

Bọtịnụ nhọrọ ọnọdụ
Port njikwa
LED Console Port USB2.0 Port (Type-C/RJ45)

Ọdụ ụgbọ mmiri 1G RJ45

10G SFP+ Slot LED

The front panel of S6500-24M4Y is shown as the following figure.

Bọtịnụ nhọrọ ọnọdụ
Port njikwa
LED Console Port USB2.0 Port (Type-C/RJ45)

Ọdụ ụgbọ mmiri 2.5G RJ45

25G SFP28 Slot LED

The front panel of S6500-24MPP4Y is shown as the following figure.

Bọtịnụ nhọrọ ọnọdụ
Port njikwa
LED Console Port USB2.0 Port (Type-C/RJ45)

Ọdụ ụgbọ mmiri 2.5G RJ45

25G SFP28 Slot LED

Okwu mmalite 03

Omada Campus Stackable L3 Managed Switch The front panel of S6500-48M6Y is shown as the following figure.

Bọtịnụ nhọrọ ọnọdụ
Port njikwa

LED Console Port USB2.0 Port (Type-C/RJ45)

Ọdụ ụgbọ mmiri 2.5G RJ45

The front panel of S6500-48MPP6Y is shown as the following figure.

25G SFP28 Slot LED

Bọtịnụ nhọrọ ọnọdụ
Port njikwa
LED Console Port USB2.0 Port (Type-C/RJ45)

Ọdụ ụgbọ mmiri 2.5G RJ45

25G SFP28 Slot LED

LED Indication LED
PWR1* PWR2
SYS FAN PoE MAX
(For S6500-24GP4XF, S6500-48GP6XF, S6500-24MPP4Y, S6500-48MPP6Y)
MGMT
MST

04 Okwu mmalite

Omada Campus Stackable L3 Managed Switch

Ikanam

Ngosipụta

Port 1-24 of S6500-24GP4XF/
Port 1-48 of S6500-48GP6XF
(When the SPEED LED is on)

Green On: Na-agba ọsọ na 1000 Mbps, mana enweghị ọrụ. Green na-egbuke egbuke: Na-agba ọsọ na 1000 Mbps na-ebufe ma ọ bụ na-anata data. Yellow On: Na-agba ọsọ na 10Mbps/100 Mbps, mana enweghị ọrụ. Ọkụ na-acha odo odo: Na-agba ọsọ na 10Mbps/100 Mbps ma na-ebufe ma ọ bụ na-anata data. Gbanyụọ: Ọ nweghị ngwaọrụ ejikọrọ na ọdụ ụgbọ mmiri kwekọrọ.

Port 1-24 of S6500-24M4Y & S6500-24MPP4Y/
Port 1-48 of S6500-48M6Y & S6500-48MPP6Y
(When the SPEED LED is on)

Green On: Running at 2.5 Gbps, but no activity. Green Flashing: Running at 2.5 Gbps and transmitting or receiving data. Yellow On: Running at 10 Mbps/100 Mbps/1000 Mbps, but no activity. Yellow Flashing: Running at 10 Mbps/100 Mbps/1000 Mbps and transmitting or receiving data. Off: No device is linked to the corresponding port.

Port 1-24 of S6500-24GP4XF, S6500-24M4Y &
S6500-24MPP4Y/
Port 1-48 of S6500-48GP6XF, S6500-48M6Y &
S6500-48MPP6Y
(Mgbe STK LED na-agbanye)

Na: Nọmba ọdụ ụgbọ mmiri na-egosi otu ID dị na topology tojupụtara.

Port 1-24 of S6500-24GP4XF & S6500-24MPP4Y/
Port 1-48 of S6500-48GP6XF & S6500-48MPP6Y
(Mgbe PoE LED na-agbanye)

Green On: The port is supplying power normally. Green Flashing: The supply power exceeds the correponding port’s maximum power. Yellow On: Overload or short circuit is detected. Off: Not providing PoE power on the port

Port 25-28 of S6500-24GP4XF/ Port 49-54 of S6500-48GP6XF ***

Green On: Na-agba ọsọ na 10 Gbps, mana enweghị ọrụ. Green Flashing: Na-agba ọsọ na 10 Gbps ma na-ebufe ma ọ bụ na-anata data. Yellow On: Na-agba ọsọ na 1 Gbps, mana enweghị ọrụ. Ọkụ na-acha odo odo: Na-agba ọsọ na 1 Gbps ma na-ebufe ma ọ bụ na-anata data. Gbanyụọ: Ọ nweghị ngwaọrụ ejikọrọ na ọdụ ụgbọ mmiri kwekọrọ.

Port 25-28 of S6500-24M4Y & S6500-24MPP4Y/
Port 49-54 of S6500-48M6Y & S6500-48MPP6Y***

Green On: Running at 25 Gbps, but no activity. Green Flashing: Running at 25 Gbps and transmitting or receiving data. Yellow On: Running at 1 Gbps/10 Gbps, but no activity. Yellow Flashing: Running at 1 Gbps/10 Gbps and transmitting or receiving data. Off: No device is linked to the corresponding port.

*By default, S6500-24GP4XF is shipped with a PSM500-AC power supply module, S6500-24M4Y/S650048M6Y is shipped with a PSM550-AC power supply module, and S6500-48GP6XF/S6500-24MPP4Y/ S6500-48MPP6Y is shipped with a PSM900-AC power supply module. One more power supply module needs to be purchased separately.
**By default, both PWR1 and PWR2 will work simultaneously in the load sharing mode. They can also work simultaneously in the redundant power supply mode: for S6500-24GP4XF/S6500-48GP6XF/S650024MPP4Y/S6500-48MPP6Y, you can specify the primary power supply and the backup power supply according to your needs; for S6500-24M4Y/S6500-48M6Y, you can only set PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply.
***All 10 Gbps SFP+ slots and 25 Gbps SFP28 slots can be used as uplink ports or stacking ports. When used as stacking ports, the slots need to run at the highest speed.

Okwu mmalite 05

Omada Campus Stackable L3 Managed Switch The front panel of S7500-26XF6Y is shown as the following figure.
Port njikwa

Ikanam

Console Port USB3.0 Port

(RJ45/Type-C)

Nhọrọ ọnọdụ

Bọtịnụ

10G SFP+ Slot (Port 1-26)

The front panel of S7500-48XF4C is shown as the following figure.

LED 25G SFP28 Slot (Port 27-32)

Bọtịnụ nhọrọ ọnọdụ
Port njikwa
LED Console Port USB3.0 Port (Type-C/RJ45)

10G SFP+ Slot (Port 1-48)

The front panel of S7500-24Y4C is shown as the following figure.

100G QSFP28 Slot LED (Port 49-52)

Port njikwa

Ikanam

Ọdụ ụgbọ mmiri USB3.0

Port Console

(RJ45/Type-C)

Bọtịnụ nhọrọ ọnọdụ

25G SFP28 oghere

Ikanam

(Ọdụ ụgbọ mmiri 1-24)

The front panel of S7500-48Y8C is shown as the following figure.

100G QSFP28 Slot (Port 25-28)

LED Mode Selection Button

25G SFP28 Slot (Port 1-48)

06 Okwu mmalite

100G QSFP28 Slot (Port 49-56)

Omada Campus Stackable L3 Managed Switch The front panel of S7500-32C is shown as the following figure.

Bọtịnụ nhọrọ ọnọdụ
Ọdụ ụgbọ mmiri njikwa
Ọdụ ụgbọ mmiri USB3.0

Console Port (Type-C/RJ45)

100G QSFP28 oghere

Ikanam

Note: S7500-24Y4C and S7500-48Y8C are designed for installation in Network Telecommunications Facilities (NTFs) where ambient temperature and humidity are controlled.

LED Indication LED
PWR1* PWR2
SYS FAN
MGMT
MST
Port 1-26 of S7500-26XF6Y/ Port 1-48 of S7500-48XF4C
(Mgbe SPD LED na-agbanye)
Port 1-24 of S7500-24Y4C/ Port 1-48 of S7500-48Y8C
(When the SPD/SPEED LED is on)

Ngosipụta
Green On: The power supply works properly. Green Flashing: The power supply module is not plugged in properly or not compatible with the switch. Yellow On: The power supply works properly but the switch is powered by the other power supply.** Yellow Flashing: The power supply module is plugged in properly but there’s is no AC power input; abnormal power supply. Off: No power supply module is inserted.
Na-egbuke egbuke: Mgbanwe na-arụ ọrụ nke ọma. Gbanyụọ ma ọ bụ gbanyụọ: Mgbanwe na-arụ ọrụ na-ekwesịghị ekwesị.
Green: Ndị fan niile na-arụ ọrụ nke ọma. Yellow: Ọ bụghị ndị Fans niile na-arụ ọrụ nke ọma.
On: A device is linked to the port. Flashing: Transmitting or receiving data. Off: No device is linked to the port.
Mara:
For S7500-48Y8C, this LED lights green at 1 Gbps and orange at sub-1 Gbps.
On: The device functions as the master switch in the stack topology or it works individually. Off: The device functions as the member switch in the stack topology.
Green On: Na-agba ọsọ na 10 Gbps, mana enweghị ọrụ. Green Flashing: Na-agba ọsọ na 10 Gbps ma na-ebufe ma ọ bụ na-anata data. Yellow On: Na-agba ọsọ na 1 Gbps, mana enweghị ọrụ. Ọkụ na-acha odo odo: Na-agba ọsọ na 1 Gbps ma na-ebufe ma ọ bụ na-anata data. Gbanyụọ: Ọ nweghị ngwaọrụ ejikọrọ na ọdụ ụgbọ mmiri kwekọrọ.
Green On: Running at 25 Gbps, but no activity. Green Flashing: Running at 25 Gbps and transmitting or receiving data. Yellow On: Running at 1 Gbps/10 Gbps, but no activity. Yellow Flashing: Running at 1 Gbps/10 Gbps and transmitting or receiving data. Off: No device is linked to the corresponding port.

Okwu mmalite 07

Omada Campus Stackable L3 Managed Switch

Ikanam

Ngosipụta

Port 27-32 of S7500-26XF6Y ***
(Mgbe SPD LED na-agbanye)

Port 49-52 of S7500-48XF4C/
Port 25-28 of S7500-24Y4C/ Port 49-56 of S7500-48Y8C/ Port 1-32 of S7500-32C***
(When the SPD/SPEED LED is on)

Green On: Na-agba ọsọ na 100 Gbps, mana enweghị ọrụ. Green Flashing: Na-agba ọsọ na 100 Gbps ma na-ebufe ma ọ bụ na-anata data. Yellow On: Na-agba ọsọ na 40 Gbps, mana enweghị ọrụ. Ọkụ na-acha odo odo: Na-agba ọsọ na 40 Gbps ma na-ebufe ma ọ bụ na-anata data. Gbanyụọ: Ọ nweghị ngwaọrụ ejikọrọ na ọdụ ụgbọ mmiri kwekọrọ.
Mara:
For S7500-48XF4C/S7500-48Y8C/S7500-32C, the indication above applies only when the 100 Gbps QSFP28 slots work with common cables. When the slots work with 1-to-4 breakout cables, a single slot is split into four 25 Gbps interfaces. In such scenario, the LED will light green only when all four interfaces are working at 25 Gbps (maximum speed), otherwise it will light yellow. When no device is connected to any of the four interfaces, the LED will be off. (The 100 Gbps QSFP28 slots will support 1-to-4 breakout cables in a future software release.)

Port 1-32 of S7500-26XF6Y/
Port 1-48 of S7500-48XF4C/ Port 1-28 of S7500-24Y4C/ Port 1-56 of S7500-48Y8C
(Mgbe STK LED na-agbanye)

Na: Nọmba ọdụ ụgbọ mmiri na-egosi otu ID dị na topology tojupụtara.

*By default, S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C/S7500-48Y8C/S7500-32C is shipped with a PSM550-AC power supply module installed respectively. One more power supply module needs to be purchased separately. **By default, both PWR1 and PWR2 will work simultaneously in the load sharing mode. They can also work simultaneously in the redundant power supply mode with PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply. ***All 25 Gbps SFP28 slots of S7500-26XF6Y and 100 Gbps QSFP28 slots of S7500-48XF4C/S7500-24Y4C/ S7500-48Y8C/S7500-32C can be used as uplink ports or stacking ports. When used as stacking ports, the slots need to run at the highest speed.
Port Introduction (The Management Port, Console Ports, and USB Ports of S7500-48Y8C are located on the rear panel.)
Management Port Designed to connnect the device for management through web, CLI or SNMP. Do not connect this port to any outdoor device, as this may induce surge and lightning damage. Console Port Designed to connect with a computer for monitoring and configuring the switch. When the switch has an RJ45 console port and a Type-C console port, console input is active on only one console port at a time. By default, the Type-C connector takes priority over the RJ45 connector, or you can change the priority through the web. Do not connect this port to any outdoor device, as this may induce surge and lightning damage. USB Port Designed to install the USB flash disk for data storage. 1000M RJ45 Port Designed to connect to the device with a bandwidth of 10Mbps, 100 Mbps or 1000 Mbps. For PoE switches, the port can also provide power for PDs.

08 Okwu mmalite

Omada Campus Stackable L3 Managed Switch
2.5G RJ45 Port Designed to connect to the device with a bandwidth of 10 Mbps, 100 Mbps, 1000 Mbps or 2.5 Gbps. For PoE switches, the port can also provide power for PDs. 10G SFP+ Slot Designed to install the 10 Gbps/1 Gbps optical module. 25G SFP28 Slot Designed to install the 25 Gbps/10 Gbps/1 Gbps optical module. 100G QSFP28 Slot Designed to install the 100 Gbps/40 Gbps optical module. Port Feature

Nlereanya

1000M

2.5G 10G SFP+ 25G SFP28 100G QSFP28 Management Console USB

RJ45 Port RJ45 Port Slot

oghere

Port

Port Port

S6500-24G4XF

S6500-48G6XF

S6500-24GP4XF

S6500-48GP6XF

S6500-24M4Y

S6500-24MPP4Y

S6500-48M6Y

S6500-48MPP6Y

S7500-26XF6Y

S7500-48XF4C

S7500-24Y4C

S7500-48Y8C

S7500-32C

Rear Panel (The figure is for demonstration only. It may differ from your actual product. )
The rear panel of S6500-24G4XF/S6500-48G6XF is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Kensington Security Slot Grounding Terminal Power Socket

Locking Strap Slot

Cheta na: PWR1 bụ isi ike ọkọnọ na ọ na-ebute ụzọ karịa PWR2.

Okwu mmalite 09

Omada Campus Stackable L3 Managed Switch
The rear panel of S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Ebe nchekwa Kensington

Ikanam

Grounding Ọnụ

Module ọkọnọ ike

Ikanam

Locking Strap Slot

Note: By default, S6500-24GP4XF is shipped with a PSM500-AC power supply module, and S650048GP6XF/S6500-24MPP4Y/S6500-48MPP6Y is shipped with a PSM900-AC power supply module. One more power supply module needs to be purchased separately. Both PWR 1 and PWR2 can work simultaneously, or you can specify the primary power supply and the backup power supply according to your needs. Generally, the primary power supply takes priority over the backup power supply.
The rear panel of S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Grounding Ọnụ

Ikanam

Power Supply Module Locking Strap Slot

Ikanam

Ebe nchekwa Kensington

The n'azụ panel nke S7500-48Y8C gosiri dị ka ndị na-esonụ ọnụ ọgụgụ. Ọnụọgụ a bụ naanị maka ngosipụta. Mgbanwe gị nwere ike ịdị iche n'ọdịdị ya na nke egosiri.

Grounding Ọnụ

Ikanam

Eriri mkpọchi

oghere

Module ọkọnọ ike

10 Okwu mmalite

ManagemeC(nTtoyPnposeor-tCle/RPJoU4rt5S)B3P.o0wPeorrSt upplyLoMcokdiSnulgoletStraLpED

Omada Campus Stackable L3 Managed Switch
Note: By default, the device is shipped with a PSM550-AC power supply module installed. One more power supply module needs to be purchased separately. When the switch has two power supply modules installed, both PWR1 and PWR2 will work simultaneously in the load sharing mode by default. They can also work simultaneously in the redundant power supply mode with PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply.
The rear panel of S7500-32C is shown as the following figure. The figure is for demonstration purposes only. Your switch may differ in appearance from the depicted.

Ikanam ikanam
Locking Strap Slot
Power Supply Module Kensington Security Slot

Grounding Ọnụ

Ikanam
Locking Strap Slot

Module ọkọnọ ike

Note: By default, the device is shipped with a PSM550-AC power supply module installed. One more power supply module needs to be purchased separately. When the switch has two power supply modules installed, both PWR1 and PWR2 will work simultaneously in the load sharing mode by default. They can also work simultaneously in the redundant power supply mode with PWR1 as the primary power supply and PWR2 as the backup power supply. Generally, the primary power supply takes priority over the backup power supply.
Power Supply Module The pluggable power supply module PSM500-AC/PSM900-AC/PSM550-AC is an AC-input power supply module. It can convert the input voltage to 53.5 V (12 V for PSM550-AC) with the maximum output power of 500 W/900 W/550 W respectively. Kensington Security Slot Secure the lock (not provided) into the security slot to prevent the device from being stolen.
Grounding Terminal The switch already comes with lightning protection mechanism. You can also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable. For detailed lightning protection measures, refer to the Lightning Protection Guide from: https://support.omadanetworks.com/r/1004/. Locking Strap Slot Remove the instruction label and insert the AC power cable locking strap into the slot to secure the power cable.

Okwu mmalite 11

Omada Campus Stackable L3 Managed Switch

Isi nke 2 Ntinye

Ihe ngwugwu 2.1

Gbaa mbọ hụ na ngwugwu nwere ihe ndị a. Biko kpọtụrụ onye nkesa gị, ọ bụrụ na ihe ọ bụla n'ime ihe ndị edepụtara mebiri ma ọ bụ na-efu. Ọnụọgụ ndị a bụ naanị maka ngosipụta. Ihe ndị dị adị nwere ike ịdị iche n'ọdịdị na ọnụọgụ site na nke egosiri.

Gbanwee

Igwe ọkụ na eriri igwe

Ntuziaka nwụnye
Business ịkparịta ụka n'Solntanet Ngwọta
Ntuziaka nwụnye
Omada Campus Stackable L3 Managed Switch

Ihe nkwado nkwado, skru na ụkwụ rọba

2.2 Nchekwa nchekwa
Iji zere mmebi ngwaọrụ ọ bụla na mmerụ ahụ nke ahụ kpatara site na iji na-ekwesịghị ekwesị, ị ga-edebe iwu ndị a.
Nchekwa nchekwa Debe ọkụ n'oge nrụnye. Yiri eriri nkwojiaka na-egbochi ESD, wee hụ na eriri nkwojiaka nwere ezigbo kọntaktị akpụkpọ na ọ bụ
nke ọma n'ala. Jiri naanị eriri ọkụ enyere na mgba ọkụ. Gbaa mbọ hụ na ọkọnọ voltage dakọtara na nkọwapụta egosiri na azụ panel nke
ịgbanwee. Gbaa mbọ hụ na etinyere ngbanwe ahụ na ebe ikuku na-ekpo ọkụ na oghere ikuku ya adịghị
egbochiri. Emeghela ma ọ bụ wepụ ihe mkpuchi nke mgba ọkụ. Tupu ihicha ngwaọrụ, bepụ ọkụ eletrik. Ejila akwa mmiri na-ehicha ya, ma ọlị
use any other liquid cleaning method. Place the device with its bottom surface facing downwards. Only instructed person or skilled person can be allowed to install, replace, or service this device.
Chọrọ saịtị
Okpomọkụ/ iru mmiri

12 Ntinye

Omada Campus Stackable L3 Managed Switch Keep the equipment room at an appropriate level of temperature and humidity. Too much or too little humidity may lead to bad insulation, leakage of electricity, mechanical property changes, and corrosion. High temperatures may accelerate aging of the insulation materials, significantly shortening the service life of the device. To find out the best temperature and humidity conditions for the device, check the Appendix B Specifications. Clearness
Uzuzu na-akwakọba na mgba ọkụ nwere ike itinye uche ya site na ọkụ eletrik na-eme ka ọ ghara ịdị mma na kọntaktị kọntaktị ígwè. Emeela ihe ụfọdụ maka ngwaọrụ ahụ iji gbochie ọkụ eletrik kwụ ọtọ, mana ọkụ eletrik siri ike nwere ike imebi ihe eletrọnịkị dị na bọọdụ sekit dị n'ime. Iji zere mmetụta nke ọkụ eletrik kwụ ọtọ na arụ ọrụ nke mgba ọkụ, tinye ihe dị mkpa na ihe ndị a: Na-ekpuchi ngwaọrụ ahụ mgbe niile, na-edebekwa ikuku ime ụlọ ọcha. Debe ngwaọrụ ahụ nke ọma ma hụ na ebufela ọkụ eletrik. Ntinye aka eletrik
Ihe eletrọnịkị gụnyere capacitance na inductance dị na ngwaọrụ ahụ nwere ike imetụta nnyonye anya mpụga, dị ka mpụta a na-eme site na njikọta ike, njikọta inductance, na njikọ impedance. Ka ibelata ndabichi ndị a, gbaa mbọ mee usoro ndị a: Jiri ọkụ nwere ike yocha nnyonye anya nke ọma na grid ọkụ. Debe ngwaọrụ ahụ ka ọ ghara ịdị elu na ngwa siri ike dị ugbu a dịka mgbasa ozi redio
ọdụ ụgbọ mmiri. Jiri ihe mkpuchi elektrọnik mgbe ọ dị mkpa. Nchekwa ọkụ
Ntinye 13

Omada Campus Stackable L3 Managed Switch
Oke oke voltage nwere ike imepụta mmiri ozugbo mgbe àmụmà na-apụta na ikuku dị n'okporo ụzọ mgbapụta eletrik nwere ike ikpo ọkụ ozugbo ruo 20,000 Celsius. Ebe ọ bụ na ngwa ngwa ngwa a siri ike nke ukwuu imebi ngwaọrụ eletrọnịkị, a ga-emerịrị usoro nchebe ọkụ dị irè karị. Gbaa mbọ hụ na rack na ngwaọrụ ahụ bụ nke ọma. Jide n'aka na oghere ike nwere ezigbo kọntaktị na ala. Debe usoro cabling nwere ezi uche ma zere àmụmà na-akpalite. Jiri mgbama SPD (Ngwaọrụ Nchedo Surge) mgbe ị na-agbanye n'èzí.
Mara: Maka usoro nchedo ọkụ ọkụ zuru ezu, rụtụ aka na ntuziaka Nchedo ọkụ sitere na: https://support.omadanetworks.com/r/1004/. Saịtị nwụnye
When installing the device on a rack or a flat workbench, attach much importance to the following items: Install the device with its bottom surface facing down only. This equipment is not suitable for use in locations where children are likely to be present. The rack or workbench is flat, stable, and sturdy enough to support the weight of 9.5 kg at least. The rack or workbench has a good ventilation system. The equipment room is well ventilated. The rack is well grounded. Keep the device less than 1.5 meters away from the power socket.
2.3 Ngwa nwụnye
Phillips screwdriver ESD-egbochi nkwojiaka eriri eriri
Mara: Ejikwaghị ngwaọrụ ndị a na ngwaahịa anyị. Ọ bụrụ na ọ dị mkpa, ịnwere ike ịzụta ha iche.
2.4 Ntinye ngwaahịa
Emebere mgba ọkụ ahụ na njiri ọkụ n'ihu na azụ. Mgbe ọ na-arụ ọrụ, ikuku na-ekesa dị ka egosiri n'okpuru. Maka ikpo ọkụ ka mma, biko wụnye ngwaọrụ na ebe ikuku na-ekpo ọkụ ma hapụ 5 ruo 10 cm oghere gburugburu ngwaọrụ ahụ.
14 Ntinye

Ọgụgụ 2-1

Mgbasa ikuku

Omada Campus Stackable L3 Managed Switch

Ntinye Desktop

Iji wụnye ngwaọrụ na desktọpụ, soro usoro ndị a:
1. Tọọ ngwaọrụ ahụ n'elu ala dị larịị nke siri ike iji kwado ịdị arọ nke ngwaọrụ ahụ na ihe niile.

2. Wepụ akwụkwọ nkwado nrapado na ụkwụ rọba.

3. Tinye ụkwụ roba na ala nke ngwaọrụ ahụ ka ọ ghara ịdaba mgbe etinye ya na desktọpụ.

Ọgụgụ 2-2

Ntinye Desktop

N'ala ala nke ngwaọrụ notch

Nwụnye rack

Ihe ngwugwu ahụ gụnyere 6 ụzọ abụọ dị iche iche na-arị elu brackets, a na-egosipụta foto ha n'okpuru ma nwee ike ịdị iche na ngwaahịa ndị ahụ.

Ọgụgụ 2-3

Ihe nkwado nkwado

Screw Hole Group 2

Bracket D Bracket C Bracket B Bracket A

Screw Hole Group 1
Screw Hole Group 3

Mpempe akwụkwọ F

Screw Hole Group 4-2 (for device with 420mm depth)

Screw Hole Group 5

Ịghasa Oghere

Otu 4-1

Screw Hole Group 4-3

(for device with 380mm depth)

(for device with

460mm depth)

Bracket E

Ntinye 15

Omada Campus Stackable L3 Managed Switch

Before installing the device in an EIA standard-sized, 19-inch rack, please check the efficiency of the grounding system and the stability of the rack, then wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded. Bracket B, C & E have two adjustable ears, please measure the distance between the front-post rack and the rear-post rack, and determine a suitable mounting method from below:

Usoro

Ngosipụta

Front: Bracket A Rear: Bracket D (Screw Hole Group 1) + Bracket B (Ear towards back)

Rack Distance
(For device with a depth of 380mm)

Rack Distance
(For device with a depth of 420mm)

Rack Distance
(For device with a depth of 460mm)

498-640mm 538-680mm 578-720mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 1) + Bracket C (Ear towards back)

477-498mm 517-538mm 557-578mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 2) + Bracket C (Ear towards back)

429-477mm 469-517mm 509-557mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 2) + Bracket C (Ear towards front)

410-429mm 450-469mm 490-509mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 3) + Bracket C (Ear towards back)

357-410mm 397-450mm 437-490mm

Front: Bracket A Rear: Bracket D (Screw Hole Group 2) + Bracket B (Ear towards back)

282-410mm 322-450mm 362-490mm

16 Ntinye

Omada Campus Stackable L3 Managed Switch

Front: Bracket A Rear: Bracket F (Screw Hole Group 4) + Bracket E (Ear towards back)

555-936mm 555-936mm 555-936mm

Front: Bracket A Rear: Bracket F (Screw Hole Group 5) + Bracket E (Ear towards back)

743-1121mm 743-1121mm 743-1121mm

Iji wụnye ngwaọrụ, soro ntuziaka akọwara n'okpuru:

1. Attach the M6 nuts to the racks.

Ọgụgụ 2-4

Securing M6 Nuts

×8

2. Attach the mounting brackets (B, C or E) to the rear-post racks and secure them with the provided M6 screws, as illustrated in the following figure.

Ọgụgụ 2-5

Installing Brackets on Racks

3. Attach the brackets A & D/F to the switch with the provided M3 screws.

Ntinye 17

Omada Campus Stackable L3 Managed Switch

Ọgụgụ 2-6

Installing Brackets on Switch

4. After the brackets are attached to the device, hold the switch with attached brackets up until it aligns with the brackets on the racks, and gently push the switch backwards until it is in place, then secure the device on the racks with M6 screws and fix brackets B/C or E to brackets D or F with M4 screws on both sides.

Ọgụgụ 2-7

Installing Switch on Racks

Caution: Leave 5 to 10 cm gaps around the devices for air circulation. Avoid placing heavy things on the device. Mount devices in the order demonstrated above and ensure a certain clearance between devices for
the purpose of heat dissipation.

18 Ntinye

Omada Campus Stackable L3 Managed Switch

Nwụnye Module Ike

S6500-24GP4XF is shipped with a PSM500-AC power supply module installed, S6500-48GP6XF/ S6500-24MPP4Y/S6500-48MPP6Y is shipped with a PSM900-AC power supply module installed, and S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C/S7500-48Y8C/S750032C is shipped with a PSM550-AC power supply module installed. It looks like below, and the image may differ from your actual product.

Ọgụgụ 2-8

Appearance of the Power Supply Module

Njikọ eriri ọkụ AC
MMA

Mpempe akwụkwọ na-ejigide

Extraction Handle

Ikanam

Locking Strap Slot Release Handle

Ọ bụrụ na ịchọrọ ịgbakwunye otu modul ọkọnọ ọkụ ọzọ, biko soro usoro ndị a:

1. Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded.

2. Press the extraction handle of the module with one hand, and hold the bottom of the module using your other hand. Gently push the module in along the slot guide rail.

3. Release the extraction handle to fix the power supply module in place.

Ọgụgụ 2-9

Wụnye Ngwunye Ngwunye Ike

Hapụ Aka

Caution: Do not plug the power cord until the power supply module installation is completed. When installing a power supply module, make sure it is set correctly in the operation of installation. Do not use too much force in the installation. If resistance is encountered or positions of the power
supply module appear larger during installation, you must first remove the module and then reinstall the module. If the Retainer Clips cannot spring up naturally and the power module is blocked, it may be due to the power supply module is not installed properly. Please check carefully.
The power supply module is designed with a locking strap slot. If you need to secure the power cable with the included locking strap, please follow the steps:
1. Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded.
Ntinye 19

Omada Campus Stackable L3 Managed Switch
2. Remove the instruction label on the AC power cable locking strap slot. 3. Attach the clamp to the AC power cable and insert the locking strap into the slot. 4. Adjust tightness and distance of the locking strap using clips to ensure the cable is securely fastened.
Figure 2-10 Installing the Locking Strap

Ọ bụrụ na ịchọrọ iwepụ modul ọkọnọ ọkụ, biko soro usoro ndị a:
1. Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded.
2. Depress the retainer clip to release the locking strap, and then remove the power cord from the external power supply system and the power module.
3. Press the extraction handle of the module with one hand, and pull the extraction handle using your other hand, until the module completely comes out of the chassis.
Caution: Unplug the power cord first, then remove the power supply module. When removing a power supply module, make sure that the power supply module is set correctly in the
operation of installation. In order to better protect the power supply module during removal, it is recommended that you
package it in an antistatic bag.
Nwụnye Module Fan
S6500-24GP4XF/S6500-48GP6XF/S6500-24M4Y/S6500-24MPP4Y/S6500-48M6Y/S650048MPP6Y/S7500-26XF6Y/S7500-48XF4C/S7500-24Y4C/S7500-48Y8C/S7500-32C is shipped with hot-swappable fan modules installed. They look like below, and the images may differ from your actual product.
Ọgụgụ 2-11 Mpụta nke Module Fan
Ikanam

20 Ntinye

Extraction Handle Retainer Clips Release Handle

Omada Campus Stackable L3 Managed Switch For normal operation of the switch, please ensure that models with 5 fan modules maintain at least 4 operational modules, while models with 4 fan modules maintain at least 3 operational modules. If one fan module is damaged, please replace it as follows: 1. Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well
grounded. 2. Press the extraction handle of the module with one hand, and pull the extraction handle until the
module completely comes out of the chassis.
Ọgụgụ 2-12 Wepụ Modul Fan mebiri emebi
3. Press the extraction handle of a new fan module with one hand, and hold the bottom of the module using your other hand. Gently push the module in along the slot guide rail.
4. Release the extraction handle to fix the power supply module in place. Caution: S6500-24GP4XF/S6500-48GP6XF/S6500-24M4Y/S6500-24MPP4Y/S6500-48M6Y/S6500-48MPP6Y/ S7500-26XF6Y uses hot-swappable fan modules with a maximum speed of 9,000 RPM. S7500-48XF4C/ S7500-24Y4C/S7500-48Y8C/S7500-32C uses hot-swappable fan modules with a maximum speed of 18,000 RPM. Please do not interchange or mix fan modules between models. Sharp edges on the fan module may cause injury, so please operate with caution. Make sure the damaged fan module is in place before you are going to replace it. DO NOT unplug the damaged fan module until the replacement operation. Do not use too much force in the replacement. If resistance is encountered or positions of the fan module appear larger during installation, you must first remove the module and then reinstall the module. If the Retainer Clips cannot spring up naturally and the power module is blocked, it may be due to the fan module is not installed properly. Please check carefully.
Ntinye 21

Omada Campus Stackable L3 Managed Switch

Isi nke 3 Njikọ

3.1 ọdụ ụgbọ mmiri Ethernet

Jikọọ ọdụ ụgbọ mmiri Ethernet nke mgba ọkụ na kọmputa site na eriri RJ45 dị ka ọnụ ọgụgụ ndị na-esonụ.

Ọgụgụ 3-1

Ijikọ ọdụ ụgbọ mmiri RJ45

Port RJ45

Igwe ọkụ RJ45

3.2 10G SFP+/25G SFP28/100G QSFP28 Slot

The following figure demonstrates the connection of 10G SFP+/25G SFP28/100G QSFP28 slot to an optical module

Ọgụgụ 3-2

Inserting the Fiber Module

Slot Fiber Module

3.3 ọdụ ụgbọ mmiri
CLI (Command Line Interface) na-enyere gị aka ijikwa mgba ọkụ ahụ, yabụ ị nwere ike ibunye CLI mgbe ị jikọtara PC ma ọ bụ Terminals na ọdụ ụgbọ mmiri na mgba ọkụ site na eriri (a na-enye eriri RJ45 console, ebe anaghị enye eriri Type-C)
Jikọọ ọdụ ụgbọ mmiri RJ45 nke ngwaọrụ ahụ na kọmputa gị site na eriri console dị ka ọnụ ọgụgụ a na-egosi.

22 Njikọ

Ọgụgụ 3-3

Ijikọ ọdụ ụgbọ mmiri Console (RJ45).

Omada Campus Stackable L3 Managed Switch

Jikọọ ọdụ ụgbọ mmiri Type-C nke ngwaọrụ na kọmputa gị site na eriri Type-C (anaghị enye ya) dị ka ọnụ ọgụgụ na-esonụ na-egosi.

Ọgụgụ 3-4

Ijikọ ọdụ ụgbọ mmiri Console (USB).

Note: RJ45 console port and Type-C console port cannot be used concurrently. Type-C Console port takes
priority over the RJ45 console port. The Type-C console port is hot-pluggable while the RJ45 console port is not. Keep the device power
off when plugging the console cable into the RJ45 console port. Do not connect the console port with other ports by RJ45 cable.
3.4 Nyochaa nwụnye
Mgbe ịmechara nrụnye ahụ, nyochaa ihe ndị a: Ekwesịrị ịnwe 5 ruo 10 cm nke mkpochapụ gburugburu ngwaọrụ maka ikuku ventilashị ma hụ na ikuku na-asọ.
zuru oke. Voltage nke ike ọkọnọ na-emezu ihe a chọrọ nke ntinye voltage nke ngwaọrụ. Oghere ike, ngwaọrụ na rack dabara nke ọma. Ejikọrọ ngwaọrụ a nke ọma na ngwaọrụ netwọkụ ndị ọzọ.
Njikọ 23

Omada Campus Stackable L3 Managed Switch

3.5 Ike On

Tinye njikọ nwanyị nke eriri ọkụ enyere n'ime oghere ike nke ngwaọrụ ahụ wee gbanye njikọ dị mma n'ime oghere ọkụ dị ka ọnụ ọgụgụ na-esonụ na-egosi. Gbaa mbọ hụ na voltage nke ike ọkọnọ na-emezu ihe a chọrọ nke ntinye voltage (100-240 V ~ 50/60 Hz).

Ọgụgụ 3-5

Na-ejikọta na Nnyefe Ike

Note: The figure is to illustrate the application and principle. The provided plug and module in your region
may differ from the figures above. Generally PWR1 takes priority over PWR2.

3.6 Mmalite
Mgbe emechara ngwaọrụ dị na ya, ọ na-amalite Nnwale Onwe Nke Onwe. Usoro nyocha na-agba ọsọ na-akpaghị aka iji hụ na ngwaọrụ ahụ na-arụ ọrụ nke ọma. N'oge a, ihe ngosi ọkụ ya ga-aza n'usoro ndị a:
1. PWR LED egosi ọkụ na mgbe niile. SYS LED na ihe ngosi LED nke ọdụ ụgbọ mmiri niile na-akwụsị.
2. Mgbe ihe dị ka otu nkeji gachara, ihe ngosi SYS LED na LED nke ọdụ ụgbọ mmiri niile ga-agbanye obere oge wee gbanyụọ.
3. Ọtụtụ sekọnd mgbe e mesịrị, SYS LED egosi ga-flash, nke na-anọchi anya a ọma initialization.
3.7 Topology
With stackable design, the switches can be stacked into one stack topology for higher reliability, larger bandwidth, and simpler networking. To build the stack topology, you need to prepare 2-12 switches and enough 10G SFP+/25G SFP28/100G QSFP28 modules/cables. For more details, see the table below:

Gbanwee

Ụdị(s) dakọtara

Ọnụọgụ

S6500-24G4XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-48G6XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-24GP4XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-48GP6XF S6500-24G4XF, S6500-48G6XF, S6500-24GP4XF, S6500-48GP6XF S6500-24M4Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y S6500-24MPP4Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y

2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode) 2-12 (max 12 in standalone mode, max 4 in controller mode)

24 Njikọ

Omada Campus Stackable L3 Managed Switch

S6500-48M6Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y

S6500-48MPP6Y S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y

S7500-26XF6Y S7500-26XF6Y

S7500-48XF4C S7500-48XF4C

S7500-24Y4C S7500-24Y4C

S7500-48Y8C S7500-48Y8C

S7500-32C

Enwere nhazi topology atọ maka ọnọdụ dị iche iche, biko wulite topology kwesịrị ekwesị dịka mkpa gị siri dị:

1. Chain Topology: Chain topology dị mfe ma ọ dịghị achọ njikọ eriri n'etiti nkeji mbụ na nke ikpeazụ. Ọ dabara adaba maka ikpokọta ogologo oge, mana ntụkwasị obi ya dị ntakịrị.

Ọgụgụ 3-6

Chain Topology

Stacking Port Group 2
Stacking Port Group 1

…

2. Ring Topology: Ring topology nwere ntụkwasị obi dị elu ma e jiri ya tụnyere topology yinye. Mgbe otu n'ime ụdọ dị na topology mgbanaka kwụsịrị, mgbanaka mgbanaka na-aghọ topology yinye, mana usoro nchịkọta niile ka nwere ike ịrụ ọrụ nke ọma. Topology mgbanaka chọrọ njikọ eriri n'etiti nkeji mbụ na nke ikpeazụ, yabụ na ọ dabaraghị maka ikpokọta ogologo.

Ọgụgụ 3-7

Ring Topology

Stacking Port Group 2

Stacking Port Group 1

…

Njikọ 25

Omada Campus Stackable L3 Managed Switch

3. Star Topology: Star topology jikọọ switches na a Central isi mgba ọkụ, Ya mere, ọ nwere ike budata dịkwuo data ebugharị ọnụego n'etiti otu switches mgbe na-enye otu njikwa.

Ọgụgụ 3-8

Star Topology

Stacking Port Group 2

Stacking Port Group 3

Stacking Port Group 1

…

Note: The stacking port is not allowed to connect to non-stacking port, as it may affect the operation of the
device. Stacking ports with the same group ID are not allowed to connect to stacking ports with different
group IDs, neither to different devices. A stacking port group is a logical port dedicated to stacking and needs to be bound to a stacking port.
A stacking port group can be bound to one or more stacking ports to improve bandwidth and reliability.

26 Njikọ

Omada Campus Stackable L3 Managed Switch

Isi nke 4 Nhazi

4.1 Nhazi gafereview
Ihe mgba ọkụ ahụ na-akwado nhọrọ nhazi abụọ:
Ọnọdụ kwụ ọtọ: Hazie ma jikwaa ngbanwe otu. Ọnọdụ njikwa: Hazie na jikwaa ngwaọrụ netwọkụ n'etiti. A na-atụ aro na
netwọkụ buru ibu, nke mejuputara ngwaọrụ igwe dị ka ebe nnweta, mgba ọkụ, na ọnụ ụzọ ámá.
Rịba ama: Mgbe agbanwere ngbanwe site na Standalone Mode gaa na ọnọdụ njikwa, nhazi nke mgba ọkụ ga-efunahụ. Maka nkọwa, rụtụ aka na akwụkwọ ndị metụtara ya na ebe nbudata nke onye ọrụ anyị websaịtị: https://support.omadanetworks.com/product/.

4.2 Ọnọdụ kwụ ọtọ

Na Standalone Mode, jiri kọmpụta hazie ma jikwaa mgba ọkụ site na iji GUI (Ihe nlere anya ihe eserese) ma ọ bụ CLI ( interface iwu-ahịrị).

Ọgụgụ 4-1

Topology maka Ọnọdụ kwụụrụ onwe ya

Gbanwee

Iji GUI
1. Iji nweta ibe njikwa nke mgba ọkụ ahụ, jide n'aka na mgba ọkụ na kọmputa dị n'otu subnet. Mepee ihe nchọgharị wee pịnye adreesị IP nke mgba ọkụ na mpaghara adreesị, wee pịa igodo Tinye.
Ọ bụrụ na ngbanwe ahụ nwetara adreesị IP n'aka ihe nkesa DHCP (nke bụ ọnụ ụzọ ámá), chọta adreesị IP nke mgba ọkụ na sava DHCP.
Ọ bụrụ na ọ bụghị, jiri adreesị IP ndabara 192.168.0.1 wee malite ibe njikwa mgba ọkụ.

2. Oge mbụ ị banyere, tọọ aha njirimara na paswọọdụ iji chebe netwọk gị na ngwaọrụ gị nke ọma. Mgbe nke ahụ gasị, sistemụ ahụ ga-emegharị gị ozugbo na interface nbanye iji nyochaa nzere emepụtara ọhụrụ.

3. Mgbe nbanye nke ọma, isi peeji ga-apụta. Ị nwere ike pịa menus dị n'elu na akụkụ aka ekpe iji hazie ọrụ kwekọrọ.
Maka nhazi zuru ezu, rụtụ aka na ntuziaka onye ọrụ na ntuziaka CLI. Enwere ike ịchọta ntuziaka na etiti nbudata nke onye ọrụ anyị websaịtị: https://support.omadanetworks.com/product/.
Iji CLI Tọọ njikọ Telnet ma ọ bụ SSH iji nweta mgba ọkụ site na CLI.

Nhazi 27

Omada Campus Stackable L3 Managed Switch

Jiri ọdụ ụgbọ mmiri njikwa iji nweta mgba ọkụ. Mgbe ị na-eji ọdụ ụgbọ mmiri, malite mmemme emulation nke njedebe (dị ka Hyper Terminal) na PC wee hazie mmemme emulation ọnụ dị ka ndị a:

Ọnụego Baud 38400 bps

Data Bits 8

Parity Ọ dịghị

Kwụsị ibe 1

Ọnweghị njikwa usoro

Maka nhazi zuru ezu, rụtụ aka na ntuziaka onye ọrụ na ntuziaka CLI. Enwere ike ịchọta ntuziaka na etiti nbudata nke onye ọrụ anyị websaịtị: https://support.omadanetworks.com/product/.
Note: You may need to change the password the first time you log in, which will better protect your network and devices.

4.3 Ọnọdụ njikwa
Controller Mode applies to the large scale network with mass devices. All devices can be centrally configured and monitored via Omada Pro Hardware Controller (C5300), Omada Pro Software Controller, or Omada Pro Cloud-Based Controller.
Note: Before the following configurations, make sure the switch can access the internet. When using Omada Pro Hardware/Software/Cloud-based Controller, make sure the switch and the controller are in the same subnet. Typically, the switch obtains IP address from the DHCP server. You can check the switch’s IP address on the DHCP server.

Via Omada Pro Hardware Controller (C5300)

Omada Pro Hardware Controller (C5300) is a good alternative if you have no spare PC to keep running Omada Pro Software Controller in the network. It needs to be purchased additionally. Follow the steps below to configure the Omada Pro Hardware Controller (C5300).

Ọgụgụ 4-2

Manage the network via Omada Pro Hardware Controller (C5300)

Mgbanwe ọnụ ụzọ ámá

Omada Pro Hardware Controller (C5300) EAP
28 Nhazi

EAP

Ndị ahịa

Omada Campus Stackable L3 Managed Switch

Note: Before you start, be sure to power up and connect your devices according to the topology figure. A DHCP server (typically a gateway with DHCP function enabled) is required to assign IP addresses to
the EAPs and clients in your local network. Omada Pro Controller must have network access to some Omada campus devices (the gateway,
switch, or APs) in order to find, adopt, and manage them.

1. Chọta adreesị IP nke ọnụ ụzọ ámá. Mepee ahịrị iwu na PC gị wee tinye ipconfig. N'ime ndepụta nsonaazụ, chọta ụzọ ámá ndabara, nke bụkwa adreesị IP nke ọnụ ụzọ ámá.
2. Mwepụta a web ihe nchọgharị ma tinye adreesị IP nke ọnụ ụzọ ámá. Banye n'ime ọnụ ụzọ ámá web ibe. Mgbe ahụ gaa na Network> LAN> DHCP Ndepụta ndị ahịa ka ịchọta adreesị IP nke onye na-ahụ maka gị dịka adreesị MAC ya.
3. Tinye adreesị IP nke onye na-ahụ maka gị na adreesị mmanya iji mepee ya web ibe.
4. On the Omada Pro Controller’s web ibe, soro ọkachamara iji mechaa nhazi ngwa ngwa.
5. Mgbe nhazi ngwa ngwa, ibe nbanye na-egosi. Tinye aha njirimara na paswọọdụ ị mepụtara wee pịa Banye. Mgbe ahụ ị nwere ike hazie njikwa ahụ ọzọ.
6. Ọ bụrụ na ị chọrọ ijikwa ngwaọrụ reomotely, soro usoro ndị a:
a. Gbaa mbọ hụ na agbanyere Cloud Access na njikwa gị. Site na ndabara, agbanyere Cloud Access. Gbaa mbọ hụ na igwe igwe ojii na-enwu nwayọ nwayọ.

b. Mwepụta a web ihe nchọgharị wee tinye https://omada.tplinkcloud.com na ogwe adreesị. Tinye TP-Link ID na paswọọdụ ịbanye. Pịa + Tinye njikwa wee họrọ Njikwa ngwaike ka ịgbakwunye njikwa gị. Mgbe ahụ ị nwere ike hazie njikwa njikwa ọzọ.

For more details, refer to the Installation Guide of C5300.

Site Omada Pro Software Controller

Download the Omada Pro Software Controller on a PC with Windows OS or Linux OS. Then run the file and follow the wizard to install the Omada Pro Software Controller. Follow the steps below to configure the Controller.

Ọgụgụ 4-3

Jikwaa netwọkụ site na Omada Pro Software Controller

Ọnụ ụzọ ámá

Gbanwee

Onye njikwa

Omada Pro Software Controller AP

na-agba ọsọ na PC Host

Ndị ahịa

Nhazi 29

Omada Campus Stackable L3 Managed Switch

1. Launch the Omada Pro Software Controller on your PC. After the initiation process, the controller automatically opens its web ibe. Ọ bụrụ na ọ bụghị, pịa Mwepụta ihe nchọgharị iji jikwaa netwọkụ.
2. On the Omada Pro Controller’s web ibe, soro ọkachamara iji mechaa nhazi ngwa ngwa.
3. Mgbe nhazi ngwa ngwa, ibe nbanye na-egosi. Tinye aha njirimara na paswọọdụ ị mepụtara wee pịa Banye. Mgbe ahụ ị nwere ike hazie njikwa ahụ ọzọ.
4. Ọ bụrụ na ị chọrọ ijikwa ngwaọrụ reomotely, soro usoro ndị a:
a. Make sure that Cloud Access is enabled on your controller and your controller has been bound with your TP-Link ID. On the Omada Pro Controller’s web ibe, gaa na Ntọala> Nweta igwe ojii ka ị nweta ohere igwe ojii wee kechie NJ TP-Link gị. Ọ bụrụ na ịtọlitela ya na nhazi ngwa ngwa, mafee nzọụkwụ a.
b. Mwepụta a web ihe nchọgharị wee tinye https://omada.tplinkcloud.com na ogwe adreesị. Tinye TP-Link ID na paswọọdụ iji banye. A ga-apụta ndepụta nke njikwa ejirila TP-Link ID gị. Mgbe ahụ, ị nwere ike pịa Launch iji hazie njikwa ọzọ.

Note: To manage your devices, Omada Pro Software Controller needs to keep running on your computer.

Site Omada Pro Onye njikwa dabere na igwe ojii

Omada Pro Cloud-based Controller bụ ezigbo nhọrọ na-enweghị mkpa ịwụnye njikwa ngwanrọ na PC.

Ekwesịrị ịzụrụ ikikere ọzọ.

Ọgụgụ 4-4

Jikwaa netwọkụ ahụ site na Omada Pro Cloud-based Controller

Omada igwe ojii

Ọnụ ụzọ ámá

Gbanwee

Ndị ahịa
1. Contact the sales staff to grant the Omada Pro Cloud-Based Controller permission. 2. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar. Log in with
your TP-Link ID.
30 Nhazi

Omada Campus Stackable L3 Managed Switch 3. Click + Add Controller and choose Cloud-Based Controller to add an Omada Pro Controller. Then
you can launch the controller to adopt and manage devices. * Omada App With the Omada app, you can also manage your controller at a local site or a remote site via your mobile device. For the detailed configurations, refer to the User Guide of the controller. The guide can be found on the download center of our official websaịtị: https://support.omadanetworks.com/product/.
Nhazi 31

Omada Campus Stackable L3 Managed Switch
Ihe Odide A Nchọpụta nsogbu
Q1. Kedu ihe m ga - eme ma ọ bụrụ na echefuru aha njirimara na paswọọdụ nke ọkụ ọkụ?
1. Jikọọ console ọdụ ụgbọ mmiri nke PC na console n'ọdụ ụgbọ mmiri nke mgba ọkụ na-emeghe ọnụ emulation omume.
2. Gbanyụọ ma malitegharịa mgba ọkụ. Mee omume nke mmemme emulation nke njedebe gosipụtara iji ruo menu bootUtil. Omume dị iche site na ngwaahịa gaa na ngwaahịa. Edepụtara omume nwere ike ime n'okpuru: · Pịa igodo ọ bụla ka ịkwụsị autoboot. Pịa CTRL-B ka iru menu bootUtil.
3. A ga-egosi menu bootUtil. Tinye nọmba 6 ka ịhọrọ nhọrọ "nkwụghachi okwuntughe" wee tinye Y ka ihichapụ ndị ọrụ na okwuntughe niile. Mgbe ahụ ị nwere ike ịtọgharịa aha njirimara na paswọọdụ.
Q2. Kedu ihe kpatara PWR LED ji arụ ọrụ nke ọma? Ekwesịrị ịgbanye PWR/Power LED ọkụ mgbe sistemụ ike na-arụ ọrụ nke ọma. Ọ bụrụ na PWR/Power LED na-arụ ọrụ na-adịghị mma, mee usoro ndị a:
1. Jide n'aka na ejikọrọ eriri ọkụ nke ọma, na kọntaktị ike bụ ihe nkịtị. 2. Gbaa mbọ hụ na voltage nke ike ọkọnọ na-emezu ihe a chọrọ nke ntinye voltage nke
ịgbanwee.
Q3. Kedu ihe m ga-eme ma ọ bụrụ na enweghị m ike ịnweta web ibe njikwa? Gbalịa ihe ndị a:
1. Lelee ọdụ ụgbọ mmiri ọ bụla LED na ngbanwe ma jide n'aka na ejikọrọ eriri Ethernet nke ọma. 2. Gbalịa ọdụ ụgbọ mmiri ọzọ na mgba ọkụ wee hụ na eriri Ethernet dabara adaba ma na-arụ ọrụ nke ọma. 3. Gbanyụọ mgba ọkụ na, mgbe obere oge gasịrị, gbanye ya ọzọ. 4. Jide n'aka na edobere adreesị IP nke PC gị n'ime subnet nke mgba ọkụ. 5. Ọ bụrụ na ị ka na-enweghị ike ịnweta nhazi peeji nke, tọgharịa mgba ọkụ ya factory defaults. Mgbe ahụ
Ekwesịrị ịtọ adreesị IP nke PC gị ka 192.168.0.x (“x” bụ ọnụọgụ ọ bụla sitere na 2 ruo 254) yana nkpuchi subnet dị ka 255.255.255.0.
Q4. Kedu ihe kpatara na mmemme emulation nke njedebe anaghị egosipụta nke ọma? Gbalịa ihe ndị a:
1. Jide n'aka na ọkụ eletrik bụ ihe nkịtị na eriri njikwa ejikọrọ nke ọma. 2. Lelee ma eriri njikwa bụ ụdị ziri ezi. 3. Gbaa mbọ hụ na paramita nke mmemme emulation nke njedebe ziri ezi: hazie Bits kwa sekọnd
dị ka 38400, Data ibe n'ibe dị ka 8, Parity dị ka Ọ dịghị, Kwụsị ibe n'ibe dị ka 1, na Flow akara ka Ọ dịghị.
32 Ihe mgbakwunye Nchọpụta nsogbu

Omada Campus Stackable L3 Managed Switch

Nkọwapụta Mgbakwunye B

Specifications for S6500 Series Switches

Ihe

Ọdịnaya

IEEE 802.3, IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3ae, IEEE 802.3x

Ụkpụrụ

IEEE 802.3af/at (For S6500-24GP4XF, S6500-48GP6XF) IEEE 802.3af/at/bt (For S6500-24MPP4Y, S6500-48MPP6Y)

IEEE 802.3bz, IEEE 802.3by, IEEE 802.3cc (For S6500-24M4Y, S6500-24MPP4Y, S6500-48M6Y, S6500-48MPP6Y)

10BASE-T: 2-pair UTP/STP of Cat. 3,4,5 (maximum 100 m) 100BASE-TX: 2-pair UTP/STP of Cat. 5 or above (maximum 100 m) 1000BASE-T: 4-pair UTP/STP of Cat. 5e or above (maximum 100 m) 2.5GBASE-T: 4-pair UTP/STP of Cat. 5e or above (maximum 100 m) Transmission Medium 1000BASE-SX/LX/LX10/BX10: MMF, SMF 10GBASE-SR/LR: MMF, SMF 10G SFP+ Direct Attach Cable (SM5220-1M, SM5220-3M) 25GBASE-SR/LR: MMF, SMF (SM6110-SR, SM6110-LR) 25G SFP28 Direct Attach Cable (SM6220-1M)

S6500-24G4XF/S6500-24M4Y: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, Port 1-24, Port 25-28 S6500-24GP4XF/S6500-24MPP4Y: PWR1, PWR2, SYS, FAN, PoE Max, MGMT, MST, SPEED, STK, PoE, Port 1-24, Port 25-28 LED S6500-48G6XF/S6500-48M6Y: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, Port 1-48, Port 49-54 S6500-48GP6XF/S6500-48MPP6Y: PWR1, PWR2, SYS, FAN, PoE Max, MGMT, MST, SPEED, STK, PoE, Port 1-48, Port 49-54

Ihe mgbakwunye B nkọwapụta 33

Omada Campus Stackable L3 Managed Switch

Ego mmefu ego

For S6500-24GP4XF: 402W (with 1*PSM500-AC, by default) 720W (with 1*PSM900-AC) 720W (with 2*PSM500-AC) 720W (with 1*PSM500-AC and 1*PSM900-AC) 720W (with 2*PSM900-AC) For S6500-48GP6XF: 764W (with 1*PSM900-AC, by default) 384W (with 1*PSM500-AC) 812W (with 2*PSM500-AC) 1176W (with 1*PSM500-AC and 1*PSM900-AC) 1440W (with 2*PSM900-AC) For S6500-24MPP4Y: 751W (with 1*PSM900-AC, by default) 378W (with 1*PSM500-AC) 802W (with 2*PSM500-AC) 1168W (with 1*PSM500-AC and 1*PSM900-AC) 1534W (with 2*PSM900-AC) For S6500-48MPP6Y: 701W (with 1*PSM900-AC, by default) 328W (with 1*PSM500-AC) 752W (with 2*PSM500-AC) 1118W (with 1*PSM500-AC and 1*PSM900-AC) 1484W (with 2*PSM900-AC)

Operating Temperature & Altitude

For S6500-24G4XF/S6500-48G6XF/S6500-24M4Y/S6500-48M6Y: -5 °C to 50 °C (23 °F to 122 °F) @ 300 meters -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters For S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y: -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters

Okpomọkụ nchekwa -40 Celsius C ruo 70 Celsius (-40 °F ruo 158 Celsius F)

Iru mmiri na-arụ ọrụ 10% ruo 90% RH anaghị ekpokọta

Ebe nchekwa iru mmiri

5% ruo 90% RH anaghị ekpo ọkụ

34 Ihe mgbakwunye B nkọwapụta

Omada Campus Stackable L3 Managed Switch

Specifications for S7500 Series Switches

Ihe

Ọdịnaya

Ụkpụrụ

IEEE 802.3, IEEE 802.3x IEEE 802.3z, IEEE 802.3ae (For S7500-26XF6Y, S7500-48XF4C, S7500-24Y4C, S7500-48Y8C IEEE 802.3by, IEEE 802.3cc (For S7500-26XF6Y, S7500-24Y4C, S7500-48Y8C) IEEE 802.3 ba, IEEE 802.3bm (For S7500-48XF4C , S7500-24Y4C, S7500-48Y8C, S7500-32C)

1000BASE-SX/LX/LX10/BX10: MMF, SMF 10GBASE-SR/LR: MMF, SMF 10G SFP+ Direct Attach Cable (SM5220-1M, SM5220-3M) 25GBASE-SR/LR: MMF, SMF (SM6110-SR, SM6110-LR) 25G SFP28 Direct Attach Cable (SM6220-1M) 40GBASE-SR4/LR4: MMF, SMF (For S7500-48XF4C, S7500-24Y4C, Transmission Medium S7500-48Y8C, S7500-32C) 40G QSFP+ Direct Attach Cable (For S7500-48XF4C, S7500-24Y4C, S7500-48Y8C, S7500-32C) 100GBASE-SR4/LR4: MMF, SMF (SM9110-SR4 for S7500-48XF4C, S7500-24Y4C, S7500-48Y8C, S7500-32C) 100G QSFP28 Direct Attach Cable (SM9220-1M for S7500-48XF4C, S7500-24Y4C, S7500-48Y8C, S7500-32C)

Ikanam
Operating Temperature & Altitude

S7500-26XF6Y: PWR1, PWR2, SYS, FAN, MGMT, MST, SPD, STK, SFP+, SFP28 S7500-48XF4C: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, SFP+, QSFP28 S7500-24Y4C: PWR1, PWR2, SYS, FAN, MGMT, MST, SPD, STK, SFP28, QSFP28 S7500-48Y8C: PWR1, PWR2, SYS, FAN, MGMT, MST, SPEED, STK, SFP28, QSFP28 S7500-32C: PWR1, PWR2, SYS, MGMT, FAN, MST, SPEED, STK, QSFP28 -5 °C to 45 °C (23 °F to 113 °F) @ 300 meters -5 °C to 40 °C (23 °F to 104 °F) @ 2,000 meters -5 °C to 35 °C (23 °F to 95 °F) @ 3,000 meters

Okpomọkụ nchekwa -40 Celsius C ruo 70 Celsius (-40 °F ruo 158 Celsius F)

Iru mmiri na-arụ ọrụ 10% ruo 90% RH anaghị ekpokọta

Ebe nchekwa iru mmiri

5% ruo 90% RH anaghị ekpo ọkụ

For S7500-26XF6Y, S7500-48XF4C, and S7500-24Y4C, the maximum operating temperature supported can reach 50 °C (122 °F) @ 300 meters, 45 °C (113 °F) @ 2,000 meters, and 40 °C (104 °F) @ 3,000 meters.
Elu akwadoro bụ oke osimiri ruo 5000 m. Ekwesiri iburu n'uche na mgbe elu dị n'elu 2000 m, maka mita 220 ọ bụla nke elu elu, okpomọkụ kachasị arụ ọrụ ga-ada site na 1 ° C (1.8 ° F).

Ihe mgbakwunye B nkọwapụta 35

Omada Campus Stackable L3 Managed Switch

Nkọwapụta maka modul na-enye ike

PSM500-AC
(For S6500-24GP4XF/ S6500-48GP6XF/ S6500-24MPP4Y/ S6500-48MPP6Y)

PSM900-AC
(For S6500-24GP4XF/ S6500-48GP6XF/ S6500-24MPP4Y/ S6500-48MPP6Y)

PSM550-AC
(For S6500-24M4Y/ S6500-48M6Y/ S7500-26XF6Y/ S7500-48XF4C/ S7500-24Y4C/ S7500-48Y8C/ S7500-32C)

Ntinye ike

100 V240 V~ 50/60 Hz 8A

100-120V (included)~ 50/60Hz 12A (for locations using low voltage, see specifications for specific countries/ regions)
120 (not included)240V~ 50/60Hz 10A (for other locations)

100 V240 V~ 50/60 Hz 7A

Mmepụta Voltage

Primary: 53.5 VDC Standby: 12 VDC

Primary: 12 VDC Standby: 12 VDC

Mmepụta ugbu a

9.35 A (Oke)

16.5 A (Oke)

45 A (Oke)

Ike mmepụta

500 W (Nke kachasị)

900 W (Nke kachasị)

550 W (Nke kachasị)

Elu arụ ọrụ

For PSM500-AC/PSM900-AC: Sea level to 3000 m For PSM550-AC: Sea level to 5000 m

36 Ihe mgbakwunye B nkọwapụta

CE Mark ịdọ aka ná ntị
Nke a bụ ngwaahịa klaasị A. N'ime ụlọ, ngwaahịa a nwere ike bute nnyonye anya redio, nke a ga-achọrọ onye ọrụ mee ihe zuru oke.
Nkwuwapụta nke Nkwekọrịta EU
TP-Link si ebe a na-ekwupụta na mgba ọkụ ahụ kwekọrọ na ihe ndị dị mkpa chọrọ yana usoro ntụziaka ndị ọzọ dị mkpa 2014/30/EU, 2014/35/EU, 2011/65/EU na (EU)2015/863. Enwere ike ịchọta nkwupụta nkwenye EU izizi na https://www.tp-link.com/en/support/ce/
Nkwupụta Nkwekọrịta UK
TP-Link ugbu a na-ekwupụta na ngbanwe ahụ kwekọrọ na ihe ndị dị mkpa chọrọ na ihe ndị ọzọ dị mkpa nke Iwu Nkwekọrịta Electromagnetic 2016 na Iwu Ngwá Ọrụ (Safety) 2016. Enwere ike ịchọta nkwupụta nkwenye UK mbụ na https://www.tp-link.com/support/ukca/
, .
kpachara anya:
Osisi okpukpu abụọ, na-anọpụ iche. Kwupu njikọ mains tupu ị rụọ ọrụ.
Ozi nchekwa
· Debe ngwaọrụ ahụ na mmiri, ọkụ, iru mmiri ma ọ bụ gburugburu ebe ọkụ. Anwala ịkwasa, rụkwaa, ma ọ bụ gbanwee ngwaọrụ ahụ. Ọ bụrụ na ịchọrọ ọrụ, biko kpọtụrụ anyị. Debe ngwaọrụ ahụ na elu ala ya gbadaa. A na-eji plọg dị na eriri ọkụ ọkụ dị ka ngwaọrụ nkwụsị, oghere oghere ga-adị
dị mfe ịnweta. · Tinye ngwaahịa ahụ n'ime mgbidi mgbidi na njikọ earthing site na eriri ọkụ ọkụ
or plug. · The socket-outlet shall be installed near the equipment and shall be easily accessible. · The PoE ports shall not be used to charge lithium batteries or devices supplied by lithium
batrị.

· Operating temperature: For S6500-24G4XF/S6500-48G6XF/S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/ S7500-48XF4C/S7500-24Y4C: -5 °C to 50 °C (23 °F to 122 °F) @ 300 meters -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters For S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y: -5 °C to 45 °C (23 °F to 113 °F) @ 2,000 meters -5 °C to 40 °C (23 °F to 104 °F) @ 3,000 meters S7500-48Y8C/S7500-32C: -5 °C to 45 °C (23 °F to 113 °F) @ 300 meters -5 °C to 40 °C (23 °F to 104 °F) @ 2,000 meters -5 °C to 35 °C (23 °F to 95 °F) @ 3,000 meters
· : S6500-24G4XF/S6500-48G6XF/S6500-24M4Y/S6500-48M6Y/S7500-26XF6Y/S7500-48XF4C/ S7500-24Y4C -5°C 50°C23°F 122°F@ 300 -5°C 45°C23°F 113°F@ 2,000 -5°C 40°C23°F 104°F@ 3,000 S6500-24GP4XF/S6500-48GP6XF/S6500-24MPP4Y/S6500-48MPP6Y -5°C 45°C23°F 113°F@ 2,000 -5°C 40°C23°F 104°F@ 3,000 S7500-48Y8C/S7500-32C -5°C 45°C23°F 113°F@ 300 -5°C 40°C23°F 104°F@ 2,000 -5°C 35°C23°F 95°F@ 3,000
This equipment is not suitable for use in locations
where children are likely to be present.

Biko gụọ ma soro ozi nchekwa dị n'elu mgbe ị na-arụ ọrụ ngwaọrụ. Anyị enweghị ike ikwe nkwa na ọ nweghị ihe mberede ma ọ bụ mmebi ga-eme n'ihi iji ngwaọrụ na-ekwesịghị ekwesị. Biko jiri nlezianya jiri ngwaahịa a rụọ ọrụ n'ihe egwu nke gị.

Maka nkwado teknụzụ, ntuziaka onye ọrụ na ozi ndị ọzọ, biko gaa na https://support.omadanetworks.com/, ma ọ bụ naanị lelee koodu QR.
© 2026 TP-Njikọ 7100002759 REV2.0.1

Akwụkwọ / akụrụngwa

L3Campus Stackable Managed Switch

User Manual · L3 Campus Stackable Managed Switch, L3, Campus Stackable Managed Switch, Stackable Managed Switch, Managed Switch, Switch

Ntụaka

omada.tplinkcloud.comomada.tplinkcloud.com
support.omadanetworks.com/support.omadanetworks.com
support.omadanetworks.com/document/support.omadanetworks.com
support.omadanetworks.com/product/support.omadanetworks.com
support.omadanetworks.com/r/1004/support.omadanetworks.com
omadanetworks.com/www.omadanetworks.com
tp-link.com/en/support/ce/www.tp-link.com
tp-link.com/support/ukca/www.tp-link.com
Akwụkwọ ntuziaka onye ọrụmanual.tools

Published: February 16, 2026

Emelitere: Febụwarị 18, 2026

Omada L3 Campus Stackable Managed Switch User Manual

L3Campus Stackable Managed Switch

Nkọwapụta

Ntuziaka ojiji ngwaahịa

Isi nke 2: Nwụnye

Nkeji 3: Connection

Isi nke 4: Nhazi

FAQ

Q: What should I do if the LED indications show an error?

Akwụkwọ / akụrụngwa

Ntụaka

Jụọ ajụjụ

Isiokwu ndị emetụtara

L3Campus Stackable Managed Switch

Nkọwapụta

Ntuziaka ojiji ngwaahịa

Isi nke 2: Nwụnye

Nkeji 3: Connection

Isi nke 4: Nhazi

FAQ

Q: What should I do if the LED indications show an error?

Akwụkwọ / akụrụngwa

Ntụaka

Jụọ ajụjụ

Jụọ ajụjụ Cancel question

Isiokwu ndị emetụtara

Kacha ọhụrụ omada Akwụkwọ ntuziaka