MOONS NPSUGMDHB Wireless Node Controller Owner’s Manual

MOONS NPSUGMDHB Wireless Node Controller

Nkọwapụta

• Customer’s Part Number:
• MOONS’ Part Number: 4696355000211
• Model: NPSUGMDHB
• P/N: A8768

Isiokwu na-agbanwe na-enweghị ọkwa

nkowa

• The Wireless Node Controllers can be installed in the lighting control box, lamp chamber or installed self-contained under eaves or other sheltered areas due to the solid metal enclosure.
• It is very small size and excellent waterproof.
• It can automatically identify different types of LED driver, such as 0-10V, DALI-2/D4i and DMX(RDM).
• Supports 2 channels 0-10V for color temperature adjustment.
• Supports RGBW color.
• Supports dynamic scenes and animations.
• It communicates with the gateway through a WPAN (Sub-GHz).
• Self-building and self-healing MESH Network.
• The sensor interface supports sensor access with digital and analog outputs.

Atụmatụ

• Ntinye voltage:12-30VDC.
• Power consumption: < 1W.
• Wireless communication: IEEE 802.15.4-915MHz.
• Automatically identify dimming mode.
• DMX(RDM) master, up to 6 loads.
• DALI-2/D4i Single-Master Controller, up to 6 loads.
• 2 channels of 0-10V Dimmer, up to 4 loads each channel.
• RGBW color support
• Dynamic scenes and animations
• 1 channel of sensor sample ntinye.
• Save several dimming plans.
• Firmware upgrade: OTA.
• Embedded communication encryption mechanism.
• Radio frequency certification: FCC
• Warranty: 5years.

ÀJÀ

 ÀJÀ ELEKTIRIK
At 20 ℃, 50% RH, 100Kpa conditions.

Rịba ama:

1. In the case of DALI-2/D4i mode, the input voltage needs to be higher than the DALI BUS voltage.
2. Mgbe ntinye voltage is 12V, 0-10V can output 10V at most; When the output voltage is > 12V, 0-10V can output 11V.

Ọnọdụ ọrụ

EMC

Asambodo

Data igwe

Akụkụ
Dimensions are provided in the diagrams above.

Antenna

 Ngwa nhọrọ

LABEL 

Product barcode information:

• The last 8 digits of SN represent the communication address of the product.
• A” indicates that this product operates in the American frequency band;
• The QR code shows the product’s communication address.

Nkọwa ọrụ

Ọnụ ụzọ

WPAN Module

• Communicate with the Gateway. Transfer various instructions, such as: dimming command, upload power metering data, set parameters and query telemetries accordingly and so on.
• Wireless communication: IEEE 802.15.4-Sub-GHz.
• Embedded communication encryption mechanism.

Na-ebelata
Once the device is powered up, it will automatically identify the dimming mode (DALI-2/D4i / DMX(RDM) /0-10V) of the connected load. After recognition, it will automatically report its own running dimming mode and perform necessary operation in this way.

Mara: To achieve perfect recognition of the dimming type, it is recommended that the controller and the LED driver be powered on simultaneously, or the controller be powered on later than the LED driver.

0-10V na-ebelata

• If it is identified as 0-10V dimmer, it can support 2-channel independent 0-10V dimming, which can support adjusting the color temperature (tunable white LED driver and software configuration are required).
• The DIM-TO-OFF LED drivers should be used; the LED drivers’ output will turn off once the dimming voltage bụ <0.5V.
• Support positive and negative logic dimming (configuration required).
• If each channel is connected to multiple LED drivers, the maximum output current of each channel is 10mA, and if the load current is >10mA, the output voltage will be not accurate.

Mara: Mgbe ntinye voltage is 12V, 0-10V can output 10V at most; When the output voltage is > 12V, 0-10V can output 11V.

DMX(RDM)

• If identified as a DMX(RDM) master, it can support up to 6 loads (maximum 3 slots for each load) and can be automatically addressed to support RDM instructions.
• 4 loads are recommended.

DALI-2/D4i

• If identified as a DALI-2/D4i Single-Master Controller, up to 6 loads (one address for each load) can be supported, supporting IEC62386-101/103/251/252/253/351 (TYPE D).
• 4 loads are recommended.

Mara:

• At least one of the DALI-2/D4i LED drivers needs to be set to supply power to the DALI bus.
• Maximum of 6 DALI-2/D4i LED Drivers, any DALI-2/D4i LED Drivers >4 will need the power supply disabled
• In the case of DALI-2/D4i mode, the input voltage needs to be higher than the DALI BUS voltage.

Ntinye ihe mmetụta

• 1 channel of sensor input interface.
• Sensors with 0-10V output can be accessed.
• Passive digital output can be accessed.
• Sensors must be configured in software before it is functional in system.

Ihe ngosi ọkụ

Mara: 

1.  Purple light indicates that the communication between node controller and LED driver is lost. This might be due to use wrong LED driver or LED driver is not power on or wiring error (for example the reverse connection of the DMX bus). Please check the wiring connection or the power-on status of the LED driver, and then re-power the node controller.

Ịwụnye

For DALI-2/D4i applications with sensor

For DMX(RDM) applications with sensor 

For 0-10V Dim to off applications with sensor 

 For 0-10V Tunable white applications with sensor 

 Recommended installation of antenna interface 

 Recommended installation of M18 Antenna 

Ịnye iwu

Nkwupụta FCC

Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:

1. Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ, yana
2. Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.

Ịkpachara anya: A na-adọ onye ọrụ aka na ntị na mgbanwe ma ọ bụ mgbanwe na-akwadoghị nke ọma nke ndị na-ahụ maka nnabata nwere ike imebi ikike onye ọrụ iji rụọ ọrụ ahụ.

Rịba ama: A nwalere ngwa a wee hụ na ọ dabara na oke maka ngwaọrụ dijitalụ Klas B, dịka akụkụ 15 nke Iwu FCC.

Emebere oke ndị a iji nye nchebe ezi uche dị na ya megide nnyonye anya na-emerụ emerụ na ntinye ụlọ. Akụrụngwa a na-ewepụta ojiji ma nwee ike ịgbasa ike ugboro redio yana, ọ bụrụ na etinyeghị ya ma jiri ya dịka ntuziaka ahụ siri dị, nwere ike ibute ndabichi na-emerụ ahụ na nkwukọrịta redio. Agbanyeghị, enweghị nkwa na nnyonye anya agaghị eme na otu nrụnye. Ọ bụrụ na akụrụngwa a na-ebute nnyonye anya na-emerụ ahụ na nnabata redio ma ọ bụ telivishọn, nke enwere ike ikpebi site na ịgbanyụ ma gbanye akụrụngwa, a na-agba onye ọrụ ume ka ọ nwaa idozi nnyonye anya site na otu ma ọ bụ karịa n'ime usoro ndị a:

• Megharịa ma ọ bụ bugharịa antenna nnata.
• Mee ka nkewa dị n'etiti akụrụngwa na nnata.
• Jikọọ akụrụngwa n'ime oghere na sekit dị iche na nke ejikọrọ onye nnata.
• Kpọtụrụ onye na-ere ahịa ma ọ bụ onye ọrụ redio/TV nwere ahụmahụ maka enyemaka.

Iji nọgide na-agbaso ụkpụrụ ntụzịaka RF Exposure nke FCC, ekwesịrị ịwụnye ngwa a ma rụọ ọrụ ya na anya kacha nta n'etiti 20cm radiator ahụ gị: Jiri naanị antenna wetara.

CUSTOMER’S APPROVAL STAMP
Please sign back after your approval. The specifications will come into force when we receive purchase order.

Isiokwu na-agbanwe na-enweghị ọkwa
© 2024 MOONS’. All rights reserved. All content contained herein is subject to change without prior notice. More product documentation and MOONS’ terms and conditions are available at https://www.moonsindustries.com

History Version