Ntuziaka ọrụ M5StickC Plus2
Firmware ụlọ ọrụ
Mgbe ngwaọrụ ahụ zutere okwu arụ ọrụ, ị nwere ike ịnwale re-flashing factory firmware ka ịlele ma ọ bụrụ na ngwaike adịghị arụ ọrụ. Rụtụ aka na nkuzi a. Jiri ngwa M5Burner na-egbu maramara ka ọ gbanye firmware factory na ngwaọrụ ahụ.
FAQ
Q1: Gini mere M5StickC Plus2 m ji enyo ojii/agaghị buut?
Ngwọta: M5Burner Burn onye ọrụ ụlọ ọrụ Firmware“M5StickCPlus2 ngosi onye ọrụ”
Q2: Gịnị kpatara na ọ na-arụ ọrụ naanị awa 3? Kedu ihe kpatara ya 100% na-akwụ ụgwọ na nkeji 1, wepụ eriri chaja ọ ga-agbanyụ?
Ihe ngwọta: "Bruce n'ihi na Stack plus2"Nke a bụ ngwa ngwa na-akwadoghị. Firmware na-akwadoghị nke na-egbuke egbuke nwere ike imebi akwụkwọ ikike gị, mee ka ọ kwụsie ike, ma kpughee ngwaọrụ gị n'ihe egwu nchekwa. Gaa n'ihu na ịkpachara anya.
Biko gbaa ngwa ngwa ngwa.
Nkwadebe
- Rụtụ aka na nkuzi M5Burner iji mezue nbudata ngwa ngwa na-egbu maramara, wee rụtụ aka na onyonyo dị n'okpuru ka ibudata ngwa ngwa kwekọrọ.
Budata njikọ: https://docs.m5stack.com/en/uiflow/m5burner/intro
Ntinye USB ọkwọ ụgbọ ala
Ndụmọdụ nwụnye ọkwọ ụgbọala
Pịa njikọ dị n'okpuru ka ibudata ọkwọ ụgbọala dabara na sistemụ arụmọrụ gị. Enwere ike ibudata ma tinye ngwungwu ọkwọ ụgbọ ala maka CP34X (maka ụdị CH9102) site na ịhọrọ ngwungwu nwụnye dabara na sistemụ arụmọrụ gị. Ọ bụrụ na ị na-enwe nsogbu na nbudata mmemme (dị ka nkwụsị oge ma ọ bụ "Emehieghị ide iji lekwasịrị RAM" njehie), gbalịa ịmalitegharịa ọkwọ ụgbọala ngwaọrụ.
CH9102_VCP_SER_Windows
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe
CH9102_VCP_SER_MacOS v1.7
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip
Nhọrọ Port na MacOS
Na MacOS, enwere ike ịnwe ọdụ ụgbọ mmiri abụọ dị. Mgbe ị na-eji ha, biko họrọ ọdụ ụgbọ mmiri akpọrọ wchmodem.
Nhọrọ Port
Jikọọ ngwaọrụ na kọmputa site na eriri USB. Mgbe emechara nrụnye ọkwọ ụgbọ ala, ị nwere ike họrọ ọdụ ụgbọ mmiri kwekọrọ na M5Burner.
Ọkụ
Pịa "Ọkụ" ka ịmalite usoro ọkụ.
StickC-Plus2
SKU: K016-P2
Nkọwa
StickC-Plus2 bụ ụdị nkwuputa nke Stick C-Plus. A na-akwado ya site na mgbawa ESP32-PICO-V3-02, na-enye njikọ Wi-Fi. N'ime ahụ kọmpat ya, ọ na-ejikọta akụrụngwa ngwaike dị iche iche, gụnyere IR emitter, RTC, igwe okwu, LED, IMU, bọtịnụ, buzzer, na ndị ọzọ. Ngosipụta TFT 1.14-inch nke ST7789V2 na-ebugharị yana mkpebi 135 x 240.
Enweela ike batrị ruo 200 mAh, interface ahụ dakọtara na modul usoro okpu na otu.
Ngwá ọrụ mmepe a na-egbuke egbuke na kọmpat nwere ike ịgbalite mmepụta ihe na-akparaghị ókè. StickC-Plus2 na-enyere gị aka ịmepụta ụdị ngwaahịa IoT ngwa ngwa ma na-eme ka usoro mmepe niile dị mfe. Ọbụna ndị mbido bụ ndị ọhụrụ na mmemme nwere ike ịmepụta ngwa na-adọrọ mmasị ma tinye ha n'ọrụ na ndụ n'ezie.
Nkuzi
UIFlow
Nkuzi a ga-ewebata otu esi ejikwa ngwaọrụ StickC-Plus2 site na ikpo okwu mmemme eserese UIFlow.
UiFlow2
Nkuzi a ga-ewebata otu esi ejikwa ngwaọrụ StickC-Plus2 site na ikpo okwu mmemme eserese UiFlow2.
Arduino IDE
Nkuzi a ga-ewebata otu esi eme mmemme na ijikwa ngwa StickC-Plus2 site na iji Arduino IDE.
Rịba ama
Aghọtaghị ọdụ ụgbọ mmiri
Mgbe ị na-eji eriri C-to-C, ọ bụrụ na enweghị ike ịmata ọdụ ụgbọ mmiri ahụ, biko mee usoro ike na-esonụ:
gbanyụọ StickC-Plus2, gbanyụọ ya (pịa bọtịnụ ike ruo mgbe ọkụ ndụ ndụ na-enwu), wee jikọọ eriri USB ka ọ gbanye.
Atụmatụ
- Dabere na ESP32-PICO-V3-02 nwere nkwado Wi-Fi
- Accelerometer 3-axis arụnyere na gyroscope 3-axis
- Ngwakọta IR emitter
- RTC arụnyere n'ime ya
- Igwe okwu agbakwunyere
- bọtịnụ onye ọrụ, 1.14-inch LCD, ike/ bọtịnụ nrụpụta
- 200mAh batrị Li-ion
- Njikọ mgbasawanye
- Ejikọghị ọnụ buzzer
- Enwere ike eyi & nke enwere ike ibugharị
- Platform mmepe
- UiFlow1
- UiFlow2
- Arduino IDE
- ESP-IDF
- PlatformIO
Na-agụnye
- 1 x StickC-Plus2
Ngwa
- Ngwa ndị nwere ike eyi
- Onye njikwa IoT
- Mmụta STEM
- Ọrụ N'onwe Gị
- Ngwa ụlọ mara mma
Nkọwapụta
| Nkọwapụta | Oke |
| SoC | ESP32-PICO-V3-02 240 MHz dual-core, Wi-Fi, 2 MB PSRAM, 8 MB Flash |
| Ntinye Voltage | 5V @ 500mA |
| Interface | Ụdị-C x 1, GROVE (I2C + I/O + UART) x 1 |
| Ihuenyo LCD | 1.14 inch, 135 x 240 agba TFT LCD, ST7789V2 |
| Igwe okwu | SPM1423 |
| Bọtịnụ | bọtịnụ onye ọrụ x 3 |
| Ikanam | Green LED x 1 (anaghị eme mmemme, egosi ụra) Uhie uhie x 1 (ịkekọrịta pin G19 na IR emitter) |
| RTC | BM8563 |
| Buzzer | N'elu bọọdụ na-agafe agafe buzzer |
| IMU | MPU 6886 |
| Antenna | 2.4G 3D antenna |
| Ntụtụ mpụga | G0, G25/G26, G36, G32, G33 |
| Batrị | 200 mAh @ 3.7 V, n'ime |
| Okpomọkụ na-arụ ọrụ | 0 ~ 40 Celsius C |
| Mkpuchi | Plastic (PC) |
| Nha ngwaahịa | 48.0 x 24.0 x 13.5mm |
| Ibu ngwaahịa | 16.7 g |
| Nha ngwugwu | 104.4 x 65.0 x 18.0mm |
| Mkpokọta nha | 26.3 g |
Ntuziaka ọrụ
Gbanyụọ/ Gbanyụọ
Ike: Pịa “BUTTON C” ihe karịrị sekọnd abụọ, ma ọ bụ teta site na mgbama RTC IRQ. Mgbe mgbama na-ebilite na-ebilite, mmemme ahụ ga-etinyerịrị HOLD pin (G4) ka ọ dị elu (1) iji mee ka ọkụ dị ọkụ, ma ọ bụghị ya, ngwaọrụ ahụ ga-emechi ọzọ.
Gbanyụọ ike: Na-enweghị ike USB mpụga, pịa “BUTTON C” ihe karịrị sekọnd isii, ma ọ bụ tọọ HOLD (GPIO4) = 0 n'ime mmemme ka ịgbanyụ. Mgbe ejikọrọ USB, ịpị "BUTTON C" maka ihe karịrị 6 sekọnd ga-agbanyụ ihuenyo wee banye ọnọdụ ụra (ọ bụghị nkwụsị ọkụ zuru ezu).
Atụmatụ
Ntube Pin
Uhie uhie & IR Emitter | Bọtịnụ A | Bọtịnụ B | Buzzer
| ESP32-PICO-V3-02 | GPIO19 | GPIO37 | GPIO39 | GPIO35 | GPIO2 |
| IR Emitter & Red LED | IR emitter & Red LED pin | ||||
| Bọtịnụ A | Bọtịnụ A | ||||
| Bọtịnụ B | Bọtịnụ B | ||||
| Bọtịnụ C | Bọtịnụ C | ||||
| Buzzer na-agafe agafe | Buzzer |
Ngosipụta TFT agba
Onye ọkwọ ụgbọ ala IC: ST7789V2
Mkpebi: 135 x 240
| ESP32-PICO-V3-02 | G15 | G13 | G14 | G12 | G5 | G27 |
| Ngosipụta TFT | TFT_MOSI | TFT_CLK | TFT_DC | TFT_RST | TFT_CS | TFT_BL |
Igwe okwu MIC (SPM1423)
| ESP32-PICO-V3-02 | G0 | G34 |
| MIC SPM1423 | CLK | DATA |
6-Axis IMU (MPU6886) & RTC BM8563
| ESP32-PICO-V3-02 | G22 | G21 | G19 |
| IMU MPU6886 | SCL | SDA | |
| BM8563 | SCL | SDA | |
| Onye na -ebugharị IR | TX | ||
| Uhie uhie | TX |
HY2.0-4P
| HY2.0-4P | Nwa | Uhie | Odo | Ọcha |
| PORT.CUSTOM | GND | 5V | G32 | G33 |
Nha Model
Mpempe akwụkwọ data
ESP32-PICO-V3-02
ST7789V2
BM8563
MPU 6886
SPM1423
Ngwa ngwa
Arduino
StickC-Plus2 Arduino mmalite ngwa ngwa
Ọbá akwụkwọ StickC-Plus2
StickC-Plus2 Factory Test Firmware
UiFlow1
StickC-Plus2 UiFlow1 Mmalite ngwa ngwa
UiFlow2
StickC-Plus2 UiFlow2 Mmalite ngwa ngwa
PlatformIO
[env:m5stack-stickc-plus2] ikpo okwu = espressif32@6.7.0
osisi = m5stick-c
framework = arduino
upload_speed = 1500000
Monitor_speed = 115200
build_flags =
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-okwu
-DCORE_DEBUG_LEVEL=5
lib_deps =
M5Unified=https://github.com/m5stack/M5Unified
USB ọkwọ ụgbọ ala
Pịa njikọ dị n'okpuru ka ibudata ọkwọ ụgbọ ala dabara na sistemụ arụmọrụ gị. Ihe ngwugwu nwere ndị ọkwọ ụgbọala CP34X (maka CH9102). Mgbe ị wepụtachara ihe ndekọ ahụ, mee ihe nrụnye nke dabara na omimi-bit OS gị.
Ọ bụrụ na ị na-ezute okwu ndị dị ka nkwụsị oge ma ọ bụ "Edeghị akwụkwọ maka RAM" n'oge nbudata, biko gbalịa tinyegharịa ọkwọ ụgbọala ahụ.
| Aha ọkwọ ụgbọ ala | Chip akwadoro | Budata |
| CH9102_VCP_SER_Windows | CH9102 | Budata |
| CH9102_VCP_SER_MacOS v1.7 | CH9102 | Budata |
Nhọrọ Port MacOS
Enwere ike ịpụta ọdụ ụgbọ mmiri abụọ na macOS. Biko họrọ ọdụ ụgbọ mmiri akpọrọ wchmodem.
Ibu dị mfe
Easy Loader bụ flasher mmemme nke na-abịa na firmware ngosi. Site n'ịgbaso usoro dị mfe ole na ole, ị nwere ike gbanye ya na njikwa maka nkwenye ọrụ ngwa ngwa.
| Ibu dị mfe | Budata | Rịba ama |
| Nnwale ụlọ ọrụ maka Windows | budata | / |
Ndị ọzọ
StickC-Plus2 Iweghachi Ntuziaka Firmware Factory Factory
Vidiyo
Mmalite atụmatụ StickC-Plus2
StackC Plus2 视频.mp4
Mgbanwe ụdị
| Ụbọchị mwepụta | Gbanwee nkọwa | Rịba ama |
| / | Ntọhapụ mbụ | / |
| 2021-12 | agbakwunyere ụra na ọrụ ịkpọte, ụdị emelitere na v1.1 | / |
| 2023-12 | Ewepụrụ PMIC AXP192, MCU gbanwere site na ESP32-PICO-D4 gaa ESP32-PICO-V3-02, usoro mgbanyụ/gbanyụọ dị iche, ụdị v2 | / |
Ntụle ngwaahịa
Esemokwu ngwaike
| Ngwaahịa Aha |
SoC | Njikwa Ike | Ike batrị | Ebe nchekwa | USB-UART mgbawa | Agba |
| Mkpọ C-Plus | ESP32-PICO-D4 | AXP192 | 120 mAh | 520 KB SRAM + 4 MB Flash | CH522 | Red- oroma |
| StickC-Plus2 | ESP32-PICO-V3-02 | / | 200 mAh | 2 MB PSRAM + 8 MB Flash | CH9102 | oroma |
Ọdịiche Pin
| Aha ngwaahịa | IR | Ikanam | TFT | BỤTA A | bọtịnụ B | bọtịnụ C (WAKE) |
Jide | Batrị Voltage Chọpụta |
| M5STICKC PLUS | G9 | G10 | MOSI (G15) CLK (G13) DC (G23) RST (G18) CS (G5) |
G37 | G39 | Mgbe niile bọtịnụ |
/ | Site na AXP192 |
| M5STICKC PLUS2 | G19 | G19 | MOSI (G15) CLK (G13) DC (G14) RST (G12) CS (G5) |
G37 | G39 | G35 | G4 | G38 |
Ọdịiche ngbanwu/ gbanyụọ ike
| Ngwaahịa Aha | Gbanyụọ | Gbanyụọ ike |
| Mkpọ C-Plus2 | Pịa "BUTTON C" maka ihe karịrị 2 s, ma ọ bụ teta site na RTC IRQ. Mgbe edemede, tọọ HOLD (G4) = 1 n'ime mmemme ka idobe ya gbanye, ma ọ bụghị ya, ngwaọrụ ga-emechi ọzọ. |
Na-enweghị ike USB, pịa "BUTTON C" maka ihe karịrị 6 s, ma ọ bụ tọọ HOLD (GPIO4) = 0 na mmemme iji gbanyụọ. Iji eriri USB jikọọ, ịpị "BUTTON C" maka ihe karịrị 6 s ga-agbanyụ ihuenyo wee banye ụra, mana ọ bụghị ịgbanyụ ọkụ zuru oke. |
N'ihi na StickC-Plus2 na-ewepụ PMIC AXP192, usoro mgbanyụ ma ọ bụ gbanyụọ dị iche na nsụgharị ndị gara aga. Dị ka ekwuru na mmalite nke akwụkwọ a, ọrụ ahụ yiri nke ukwuu, mana ụlọ akwụkwọ ndị akwadoro ga-adị iche. Wi-Fi na ike mgbama IR ka emelitere ma atụnyere ụdị nke gara aga.
Akwụkwọ / akụrụngwa
 |
M5STACK ESP32-PICO-V3-02 IoT Module mmepe [pdf] Ntuziaka onye ọrụ ESP32-PICO-V3-02 IoT Module Mmepe, ESP32-PICO-V3-02, IoT Development Module, Module Mmepe, Module |