LILYGO T-Ngosipụta S3 Pro 2.33inch ihuenyo mmetụ LCD ngosi WIFI Bluetooth
Ozi ngwaahịa
Nkọwapụta
- Aha ngwaahịa: T-Ngosipụta-S3 Pro
- Ụdị: V1.0
- Ụbọchị mwepụta: 2023.11
- Ihe nhazi: ESP32-S3 modul
- Gburugburu Mmepe Software: Arduino
Ntuziaka ojiji ngwaahịa
Okwu mmalite
- T-Ngosipụta-S3 Pro bụ ikpo okwu ngwaike maka mmepe ngwa site na iji modul ESP32-S3 nwere Arduino.
T-Ngosipụta-S3 Pro
- Emebere T-Display-S3 Pro iji kwado mmepe ngwanrọ maka ọrụ ngwaike.
Arduino
- Arduino bụ mpaghara mmepe ngwanrọ eji eme mmemme T-Ngosipụta-S3 Pro.
Nkwadebe
- Tupu ịmalite, hụ na etinyere ngwaọrụ ngwanrọ dị mkpa na sistemụ gị.
Malite
- Soro ntuziaka enyere na ntuziaka onye ọrụ ka ịtọlite gburugburu ebe mmepe ngwanrọ.
Hazie
- Hazie ntọala dị ka ọrụ gị chọrọ site na iji ọkachamara nhazi nhazi menu.
Jikọọ
- Mepụta njikọ dị n'etiti gburugburu mmepe gị na ngwaike T-Display-S3 Pro.
Nwale ngosi
- Gbaa ngosi iji hụ na ngwaike na ngwanrọ na-arụ ọrụ nke ọma.
Bulite Sketch
- Bulite koodu gị (sketch) na modul ESP32-S3 site na isoro usoro ndị a:
Mee na Flash
- Chịkọta koodu Arduino gị wee gbanye ya na modul ESP32-S3.
Nyochaa
- Nyochaa mmebe nke koodu gị iji dezie na dozie nsogbu ọ bụla.
FAQ
Q: Gịnị bụ nzube nke T-Ngosipụta-S3 Pro?
- A: Emebere T-Ngosipụta-S3 Pro iji nyere ndị ọrụ aka n'ịmepụta ngwa site na iji modul ESP32-S3 yana Arduino.
Ajụjụ: Kedu ka m ga-esi melite firmware na modul ESP32-S3?
- A: Ka imelite ngwa ngwa, soro usoro ndị akọwapụtara na ntuziaka onye ọrụ n'okpuru ngalaba "Bulite Sketch".
Ajụjụ: Enwere m ike iji gburugburu mmepe ngwanrọ na T-Display-S3 Pro?
- A: Mpaghara mmepe ngwanrọ akwadoro maka T-Ngosipụta-S3 Pro bụ Arduino, dịka akọwara na ntuziaka onye ọrụ a.
- Ezubere akwụkwọ a iji nyere ndị ọrụ aka ịtọlite ebe mmepe ngwanrọ maka mmepe ngwa site na iji ngwaike dabere na T-Display-S3 Pro.
- Site na example, akwụkwọ a na-egosi otu esi eji Arduino, gụnyere ọkachamara nhazi nhazi menu, na-achịkọta Arduino na nbudata firmware na modul ESP32-S3.
Ndetu mwepụta
- ndetu mwepụta ụdị ụbọchị
- 2023.11 V1.0 Mwepụta mbụ.
Okwu mmalite
T-Ngosipụta-S3 Pro
- T-Ngosipụta-S3 Pro bụ bọọdụ mmepe. Ọ nwere ike ịrụ ọrụ n'onwe ya.
- Ọ mejupụtara ESP32-S3 MCU na-akwado Wi-Fi + BLE nkwukọrịta protocol na motherboard PCB. Ihuenyo bụ 2.33-inch IPS LCD.
- N'isi modul a bụ mgbawa ESP32S3R8.
- ESP32-S3 na-ejikọta Wi-Fi (band 2.4 GHz) na ihe ngwọta Bluetooth 5.0 n'otu mgbawa, yana cores abụọ na-arụ ọrụ dị elu na ọtụtụ akụkụ ndị ọzọ. Kwadoro site na teknụzụ 40 nm, ESP32-S3 na-enye ikpo okwu siri ike, jikọtara ọnụ nke ukwuu iji gboo ihe ndị a na-aga n'ihu maka iji ike eme ihe nke ọma, nhazi kọmpat, nchekwa, arụmọrụ dị elu na ntụkwasị obi.
- Xinyuan na-enye akụrụngwa akụrụngwa na akụrụngwa akụrụngwa na-enye ndị mmepe ngwa ike iwulite echiche ha gburugburu ngwaike usoro ESP32-S3.
- Ezubere usoro mmepe sọftụwia nke Xinyuan nyere maka ngwa ngwa na-emepe emepe ịntanetị nke ihe (IoT), yana Wi-Fi, Bluetooth, njikwa ike na-agbanwe agbanwe, yana atụmatụ sistemụ ndị ọzọ dị elu.
- Ogologo oge RF bụ 2.402 GHz ruo 2.480 GHz.
- Onye nrụpụta T-Ngosipụta-S3 Pro bụ Shenzhen Xin Yuan Electronic Technology Co., Ltd.
Arduino
- Ngwa cross-platform edere na Java. Arduino Software IDE sitere na asụsụ mmemme nhazi yana gburugburu mmepe nke mmemme Wiring.
- Ndị ọrụ nwere ike ịmepụta ngwa na Windows/Linux/MacOS dabere na Arduino. A na-atụ aro ka iji Windows 10. Windows OS ejirila dị ka example na akwụkwọ a maka ihe atụ.
Nkwadebe
- Iji mepụta ngwa maka ESP32-S3 ị ga-achọ:
- Kwajuru PC na sistemụ arụmọrụ Windows, Linux ma ọ bụ Mac
- Ngwá ọrụ iji wuo ngwa maka ESP32-S3
- Arduino nwere n'ezie API maka ESP32-S3 na scripts iji rụọ ọrụ Toolchain
- Bọdụ ESP32-S3 n'onwe ya yana eriri USB iji jikọọ ya na PC
Malite
Budata ngwa ngwa Arduino
- Otu esi etinye ngwa ngwa Arduino Software (IDE) na igwe Windows
Ntuziaka mmalite ngwa ngwa
- Nke websaịtị na-enye nkuzi mmalite ngwa ngwa
- Windows: https://www.arduino.cc/en/Guide/Windows
- Linux: https://www.arduino.cc/en/Guide/Linux
- Mac OS X: https://www.arduino.cc/en/Guide/MacOSX
- Nzọụkwụ nwụnye maka Windows ikpo okwu Arduino
- Tinye interface nbudata, họrọ Windows installer ka ịwụnye ozugbo
Wụnye ngwa ngwa Arduino
Hazie
Budata Git
- Budata ngwugwu nwụnye Git.exe
Nhazi tupu ewuo
- Pịa akara ngosi Arduino, wee pịa aka nri wee họrọ
- Mepee folda ebe Họrọ ngwaike ->
- Òké Right click->
- Pịa Git Bash Ebe a
Imechi ebe nchekwa dịpụrụ adịpụ
- espressif
- cd espressif
- git clone - na-emegharị emegharị https://github.com/espressif/arduino-esp32.gitesp32
Jikọọ
Ị nọkwa ebe ahụ. Iji nwee ike ịga n'ihu, jikọọ bọọdụ ESP32-S3 na PC, lelee n'okpuru ọdụ ụgbọ mmiri a na-ahụ anya, wee chọpụta ma nzikọrịta ozi na-arụ ọrụ.
Nwale ngosi
Họrọ File>>Example>>WiFi>>WiFiScan
Bulite Sketch
Họrọ bọọdụ
Ngwaọrụ <
Bulite
Sketch -> Bulite
Nyochaa Oghere Usoro
Ngwaọrụ ->Nleba anya Oghere Usoro
Ntuziaka iwu SSC
- Nke a bụ ụfọdụ iwu Wi-Fi maka gị iji nwalee modul.
Nkọwa
- A na-eji iwu op tọọ wee jụọ ụdị Wi-Fi nke sistemụ ahụ.
Example
- nke -Q
- op -S -o mode
Oke
Isiokwu 6-1. op Usoro iwu
Oke/Nkọwa
| -Q | Ajụjụ Wi-Fi mode. |
| -S | Tọọ ọnọdụ Wi-Fi. |
| ọnọdụ | Enwere ụdị Wi-Fi 3:
• ọnọdụ = 1: ọnọdụ STA • ọnọdụ = 2: ọnọdụ AP • ọnọdụ = 3: ọnọdụ STA+AP |
sta Nkọwa
- A na-eji iwu sta nyocha nyocha netwọkụ STA, jikọọ ma ọ bụ kwupu AP, wee jụọ ọnọdụ njikọ nke interface netwọk STA.
Example
- sta -S [-s ssid] [-b bssid] [-n channel] [-h] sta -Q
- sta -C [-s ssid] [-p paswọọdụ]
- sta -D
Oke
Tebụl 6-2. sta Command Parameter
| Nkọwa parameter | |
| -S nyocha | Nyochaa Ebe Nweta. |
| - ssd | Jiri ssid nyochaa ma ọ bụ jikọọ Ebe Nnweta. |
| - b bsd | Jiri ntinye aka nyochaa ebe nnweta. |
| -n ọwa | Nyochaa ọwa. |
| -h | Gosi nsonaazụ nyocha site na iji Ebe Nweta ssid zoro ezo. |
| -Q | Gosi STA jikọọ stuts. |
| -D | Akwụsịla ya na ebe nnweta ugbu a. |
ap nkọwa
- A na-eji iwu AP tọọ parampat nke interface netwọk AP.
Example
- ap -S [-s ssid] [-p paswọọdụ] [-t encrypt] [-n channel] [-h] [-m max_sta]
- ap –Q
- ap -L
Oke Tebụl 6-3. ap Command Parameter
Nkọwa parameter
| -S | Tọọ ọnọdụ AP. |
| - ssd | Tọọ AP ssid. |
| -p paswọọdụ | Tọọ paswọọdụ AP. |
| -t ezoro ezo | Tọọ ọnọdụ nzuzo AP. |
| -h | Zoo ssid. |
| -m max_sta | Tọọ njikọ AP max. |
| -Q | Gosi paramita AP. |
| -L | Gosi adreesị MAC na adreesị IP nke ọdụ ejikọrọ. |
Mac nkọwa
- A na-eji iwu Mac jụọ ajụjụ adreesị MAC nke interface netwọk.
Example
- mac -Q [-o mode]
Oke okpokoro 6-4. Mac Command Parameter
Nkọwa parameter
| -Q | Gosi adreesị MAC. |
|
-o mode |
• ọnọdụ = 1: adreesị MAC na ọnọdụ STA.
• ọnọdụ = 2: adreesị MAC na ọnọdụ AP. |
Nkọwa DHCP
- A na-eji iwu dhcp mee ka ma ọ bụ gbanyụọ sava/onye ahịa DHCP.
Example
- dchp -S [-o mode]
- DHCP-E-o mode]
- DHCP-Q [-o mode]
Oke okpokoro 6-5. Ụkpụrụ Iwu DHCP
| -S | Malite DHCP (Onye ahịa/Ihe nkesa). |
| -E | Kwụsị DHCP (Onye ahịa/Ihe nkesa). |
| -Q | gosi ọkwa DHCP. |
| -o mode | • ọnọdụ = 1: onye ahịa DHCP nke interface STA.
• ọnọdụ = 2: DHCP nkesa nke AP interface. • ọnọdụ = 3: abụọ. |
Nkọwa IP
- A na-eji iwu ip iji tọọ ma jụọ ajụjụ adreesị IP nke interface netwọk.
Example
- ip -Q [-o mode]
- ip -S [-i ip] [-o mode] [-m nkpuchi] [-g ọnụ ụzọ ámá]
Oke Isiokwu 6-6. ip Command Parameter
| -Q | Gosi adreesị IP. |
| -o mode | • ọnọdụ = 1: adreesị IP nke interface STA.
• ọnọdụ = 2: adreesị IP nke interface AP. • ọnọdụ = 3: abụọ |
| -S | Tọọ adreesị IP. |
| -i ip | adreesị IP. |
| -m nkpuchi | Ihe nkpuchi subnet. |
| -g ọnụ ụzọ | Ọnụ ụzọ ámá ndabara. |
- reboot Nkọwa
- A na-eji iwu nrụpụta reboot iji malitegharịa bọọdụ ahụ.
- Example
- malitegharịa
- ebule
- A na-eji iwu ram wee jụọ nha nke ihe fọdụrụ na sistemụ ahụ.
- Example
- ebule
FCC ịkpachara anya
Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ọrụ ahụ.
Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ,
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.
Agaghị ejikọta ihe nnyefe a ma ọ bụ na-arụ ọrụ na njikọ antenna ma ọ bụ nnyefe ọ bụla ọzọ.
IHE dị mkpa:
Mara: A nwalere ngwa a wee hụ na ọ dabara na oke maka ngwaọrụ dijitalụ Klas B, n'okpuru akụkụ 15 nke Iwu FCC. Emebere oke ndị a iji nye nchebe ezi uche dị na ya megide nnyonye anya na-emerụ emerụ na ntinye ụlọ. Akụrụngwa a na-ewepụta, na-eji, ma nwee ike ịgbasa ike ugboro redio yana, ọ bụrụ na etinyeghị ya ma jiri ya n'okpuru ntuziaka ahụ, nwere ike ibute ndabichi na-emerụ ahụ na nkwukọrịta redio. Agbanyeghị, enweghị nkwa na nnyonye anya agaghị eme na otu nrụnye. Ọ bụrụ na akụrụngwa a na-ebute nnyonye anya na-emerụ ahụ na nnabata redio ma ọ bụ telivishọn, nke enwere ike ikpebi site na ịgbanyụ ma gbanye akụrụngwa, a na-agba onye ọrụ ume ka ọ nwaa idozi nnyonye anya site na otu ma ọ bụ karịa n'ime usoro ndị a:
- Megharịa ma ọ bụ bugharịa antenna nnata.
- Mee ka nkewa dị n'etiti akụrụngwa na onye nnata.
- Jikọọ akụrụngwa na ntinye na sekit dị iche na nke ejikọrọ onye nnata.
- Kpọtụrụ onye na-ere ahịa ma ọ bụ onye ọrụ redio/TV nwere ahụmahụ maka enyemaka.
Nkwupụta Mkpughe FCC Radiation:
Ngwa a na-akwado oke ikpughe radieshon FCC nke edobere maka gburugburu ebe anaghị achịkwa ya.
Akwụkwọ / akụrụngwa
 |
LILYGO T-Ngosipụta S3 Pro 2.33inch ihuenyo mmetụ LCD ngosi WIFI Bluetooth [pdf] Ntuziaka onye ọrụ T-Ngosipụta S3 Pro 2.33inch ihuenyo mmetụ LCD Ngosipụta WIFI Bluetooth, T-Ngosipụta S3, Pro 2.33inch ihuenyo mmetụ LCD Ngosipụta WIFI Bluetooth, Ngosipụta LCD ihuenyo WIFI Bluetooth, Ngosipụta WIFI Bluetooth, Bluetooth WIFI |