ọdịnaya zoo
1 LILYGO T Ngosipụta S3 AMOLED 1.91 Software
2 Ozi ngwaahịa
3 Ntuziaka ojiji ngwaahịa
4 Ajụjụ
5 Banyere Nduzi a
6 Okwu mmalite
7 Malite
8 Hazie
9 Jikọọ
10 Bulite Sketch
11 Ntuziaka iwu SSC
12 FCC
13 Akwụkwọ / akụrụngwa
13.1 Ntụaka

LILYGO-LOGO

LILYGO T Ngosipụta S3 AMOLED 1.91 Software

LILYGO-T-Ngosipụta-S3-AMOLED-1-91-ngwaahịa-ngwaahịa

Ozi ngwaahịa

  • Nkọwapụta:
    • Aha ngwaahịa: T-Ngosipụta-S3 AMOLED 1.91
    • Ụdị ngosi: AMOLED
    • Ngosipụta nha: 1.91 sentimita asatọ
    • Igwe njikwa: ESP32-S3
    • Gburugburu Mmepe Software: Arduino
    • Ụbọchị mwepụta: Nọvemba 2023
    • Ụdị: V1.0

Ntuziaka ojiji ngwaahịa

  • Okwu mmalite
    • T-Ngosipụta-S3 AMOLED 1.91 bụ ngwaike ikpo okwu maka ịmepụta ngwa site na iji Arduino. Ntuziaka a na-enyere ndị ọrụ aka ịtọlite ​​gburugburu mmepe ngwanrọ.
  • Malite
    • Malite site na ịtọlite ​​​​gburugburu mmepe ngwanrọ maka T-Display-S3 AMOLED 1.91.
  • Hazie
    • Soro ọkachamara nhazi nhazi menu ka ịhazi Arduino maka mmepe.
  • Jikọọ
    • Jikọọ ngwaike T-Ngosipụta-S3 AMOLED 1.91 na gburugburu mmepe gị.
  • Nwale ngosi
    • Gbaa ngosi ngosi iji hụ na nhazi ngwaike na ngwanrọ na-arụ ọrụ nke ọma.
  • Bulite Sketch
    • Chịkọta ihe osise Arduino wee bulite ya na modul ESP32-S3.
  • Mee na Flash
    • Mepụta ihe osise ahụ wee gbanye ya na modul ESP32-S3.
  • Nyochaa
    • Nyochaa mmebe nke sketị ebugoro maka nbipu na ebumnuche nnwale.
  • Ntuziaka iwu SSC
    • Ntuziaka ntụaka maka iwu SSC dị iche iche ejiri T-Display-S3 AMOLED 1.91.
  • op
    • Nkọwa nke iwu 'op'.

Ajụjụ

  • Q: Gịnị bụ nzube nke T-Ngosipụta-S3 AMOLED 1.91?
    • A: T-Ngosipụta-S3 AMOLED 1.91 bụ ngwaike ngwaike maka mmepe ngwa site na iji Arduino na ESP32-S3 microcontrollers.
  • Ajụjụ: Kedu ka m ga-esi melite firmware na modul ESP32-S3?
    • A: Soro ntuziaka dị na ntuziaka onye ọrụ iji chịkọta ngwa ngwa na Arduino wee budata ya na modul ESP32-S3.

Banyere Nduzi a

  • Ezubere akwụkwọ a iji nyere ndị ọrụ aka ịtọlite ​​ebe mmepe ngwanrọ maka imepụta ngwa site na iji ngwaike dabere na T-Display-S3 AMOLED 1.91.
  • Site na exampLe, akwụkwọ a na-egosi otu esi eji Arduino, gụnyere ọkachamara nhazi nhazi menu, na-achịkọta Arduino na nbudata ngwa ngwa na modul ESP32-S3.

Ndetu mwepụta

LILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (14)

Okwu mmalite

T-Ngosipụta-S3 AMOLED 1.91

  • T-Ngosipụta-S3 AMOLED 1.91 bụ bọọdụ mmepe. Ọ nwere ike ịrụ ọrụ n'onwe ya.
  • Ọ mejupụtara ESP32-S3 MCU na-akwado Wi-Fi + BLE nkwukọrịta protocol na motherboard PCB. Ihuenyo bụ 1.91 inch AMOLED.
  • N'isi modul a bụ mgbawa ESP32-S3-R8.
  • ESP32-S3 na-ejikọta Wi-Fi (band 2.4 GHz) na ihe ngwọta Bluetooth 5.0 na otu mgbawa, yana cores abụọ dị elu na ọtụtụ akụkụ ndị ọzọ. Kwadoro site na teknụzụ 40 nm, ESP32-S3 na-enye ikpo okwu siri ike, jikọtara ọnụ nke ukwuu iji gboo ihe na-aga n'ihu maka iji ike rụọ ọrụ nke ọma, nhazi kọmpat, nchekwa, arụmọrụ dị elu na ntụkwasị obi.
  • Xinyuan na-enye akụrụngwa akụrụngwa na akụrụngwa akụrụngwa na-enye ndị mmepe ngwa ike iwulite echiche ha gburugburu ngwaike usoro ESP32-S3. Usoro mmepe ngwanrọ nke Xinyuan nyere bụ maka imepe ịntanetị ngwa ngwa.
  • Ngwa ihe (IoT), nwere Wi-Fi, Bluetooth, njikwa ike na-agbanwe agbanwe na njirimara sistemụ ndị ọzọ dị elu.
  • Onye nrụpụta T-Ngosipụta-S3 AMOLED 1.91 bụ Xin Yuan Electronic Technology Co., Ltd.

Arduino

  • Ngwa cross-platform edere na Java. Arduino Software IDE sitere na asụsụ mmemme nhazi yana gburugburu mmepe nke mmemme Wiring. Ndị ọrụ nwere ike ịmepụta ngwa na Windows/Linux/ MacOS dabere na Arduino. A na-atụ aro ka iji Windows 10. Windows OS ejirila dị ka example na akwụkwọ a maka ihe atụ.

Nkwadebe

  • Iji mepụta ngwa maka ESP32-S3 ị ga-achọ:
    • Kọmputa nwere ma Windows, Linux ma ọ bụ Mac sistemụ
    • Ngwá ọrụ iji wuo ngwa maka ESP32-S3
    • Arduino nwere n'ezie API maka ESP32-S3 na scripts iji rụọ ọrụ Toolchain
    • Bọdụ ESP32-S3 n'onwe ya yana eriri USB iji jikọọ ya na PC

Malite

Budata ngwa ngwa Arduino

  • Otu esi etinye ngwa ngwa Arduino Software (IDE) na igwe Windows

Ntuziaka mmalite ngwa ngwa

Nke websaịtị na-enye nkuzi mmalite ngwa ngwa

Nzọụkwụ nwụnye maka Windows ikpo okwu Arduino

LILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (1)

Wụnye ngwa ngwa Arduino

LILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (2)

Hazie

Budata Git

Budata ngwugwu nwụnye Git.exe

LILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (3)

Nhazi tupu ewuo

  • Pịa akara ngosi Arduino, wee pịa aka nri wee họrọ "Mepee folda ebe"
  • Họrọ ngwaike ->
  • Òké ** Pịa aka nri ** ->
  • Pịa Git Bash Ebe a

Imechi ebe nchekwa dịpụrụ adịpụ

Jikọọ

Ị nọkwa ebe ahụ. Iji nwee ike ịga n'ihu, jikọọ bọọdụ ESP32-S3 na PC, lelee n'okpuru ọdụ ụgbọ mmiri a na-ahụ anya wee chọpụta ma nzikọrịta ozi na-arụ ọrụ.

Nwale ngosi Họrọ File>>Example>>WiFi>>WiFiScan

LILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (4)

Bulite Sketch

  • Họrọ bọọdụ
    • Ngwaọrụ -> bọọdụ -> ESP32S3 Dev Module
  • Bulite
    • Sketch -> Bulite
  • Nyochaa Oghere Usoro
    • Ngwaọrụ ->Nleba anya Oghere UsoroLILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (5)

Ntuziaka iwu SSC

Nke a bụ ụfọdụ iwu Wi-Fi maka gị iji nwalee modul.

op

  • Nkọwa
    • A na-eji iwu op tọọ wee jụọ ụdị Wi-Fi nke sistemụ ahụ.
  • ExampleLILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (6)

Oke

Isiokwu 6-1. op Command Parameter

Oke Nkọwa
-Q Ajụjụ Wi-Fi mode.
-S Tọọ ọnọdụ Wi-Fi.
ọnọdụ Enwere ụdị Wi-Fi 3:

• ọnọdụ = 1: ọnọdụ STA

• ọnọdụ = 2: ọnọdụ AP

• ọnọdụ = 3: ọnọdụ STA+AP

sta

  • Nkọwa
    • A na-eji iwu sta nyocha nyocha netwọkụ STA, jikọọ ma ọ bụ kwupu AP, wee jụọ ọkwa njikọ nke interface netwọk STA.
  • ExampleLILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (7)

Oke

Isiokwu 6-2. sta Command Parameter

Oke Nkọwa
-S nyocha Nyochaa Ebe Nweta.
Oke Nkọwa
-s si Jiri SSID nyochaa ma ọ bụ jikọọ Ebe Nnweta.
- b bsd Jiri ntinye aka nyochaa ebe nnweta.
-n ọwa Nyochaa ọwa.
-Q Gosi STA jikọọ stuts.
-D Akwụsịla ya na ebe nnweta ugbu a.

ap

  • Nkọwa
    • A na-eji iwu ap iji tọọ paramita nke interface netwọk AP.
  • ExampleLILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (8)

Oke

Isiokwu 6-3. ap Command Parameter

Oke Nkọwa
-S Tọọ ọnọdụ AP.
- ssd Tọọ AP ssid.
-p paswọọdụ Tọọ paswọọdụ AP.
-t ezoro ezo Tọọ ọnọdụ nzuzo AP.
-h Zoo ssid.
-m max_sta Tọọ njikọ AP max.
-Q Gosi paramita AP.
-L Gosi adreesị MAC na adreesị IP nke ọdụ ejikọrọ.

mac

  • Nkọwa
    • A na-eji iwu mac jụọ ajụjụ adreesị MAC nke interface netwọkụ.
  • ExampleLILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (9)

Oke

Isiokwu 6-4. Mac Command Parameter

Oke Nkọwa
-Q Gosi adreesị MAC.
-o mode • ọnọdụ = 1: adreesị MAC na ọnọdụ STA.

• ọnọdụ = 2: adreesị MAC na ọnọdụ AP.

dhcp

  • Nkọwa
    • A na-eji iwu dhcp mee ka ma ọ bụ gbanyụọ sava/onye ahịa DHCP.
  • ExampleLILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (10)

Oke

Isiokwu 6-5. dhcp Command Parameter

Oke Nkọwa
-S Malite DHCP (Onye ahịa/Ihe nkesa).
-E Kwụsị DHCP (Onye ahịa/Ihe nkesa).
-Q gosi ọkwa DHCP.
-o mode • ọnọdụ = 1: onye ahịa DHCP nke interface STA.

• ọnọdụ = 2: DHCP nkesa nke AP interface.

• ọnọdụ = 3: abụọ.

IP

  • Nkọwa
    • A na-eji iwu ip iji tọọ ma jụọ ajụjụ adreesị IP nke interface netwọk.
  • ExampleLILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (11)

Oke

Isiokwu 6-6. ip Command Parameter

Oke Nkọwa
-Q Gosi adreesị IP.
 

-o mode

 • ọnọdụ = 1: adreesị IP nke interface STA.

• ọnọdụ = 2: adreesị IP nke interface AP.

• ọnọdụ = 3: abụọ
-S Tọọ adreesị IP.
-i ip adreesị IP.
-m nkpuchi Ihe nkpuchi subnet.
-g ọnụ ụzọ Ọnụ ụzọ ámá ndabara.

malitegharịa

  • Nkọwa
    • A na-eji iwu nrụpụta reboot iji malitegharịa bọọdụ ahụ.
  • ExampleLILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (12)
  • ebule
    • A na-eji iwu ram wee jụọ nha nke ihe fọdụrụ na sistemụ ahụ.
  • ExampleLILYGO-T-Display-S3-AMOLED-1-91-Software-FIG-1 (13)

FCC

Akpachara anya FCC:

Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ọrụ ahụ. Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC.

A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:

  1. Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ, yana
  2. Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.

Agaghị ejikọta ihe nnyefe a ma ọ bụ na-arụ ọrụ na njikọ antenna ma ọ bụ nnyefe ọ bụla ọzọ.

IHE dị mkpa:
Mara: A nwalere ngwa a wee hụ na ọ dabara na oke maka ngwaọrụ dijitalụ Klas B, n'okpuru akụkụ 15 nke Iwu FCC. Emebere oke ndị a iji nye nchebe ezi uche dị na ya megide nnyonye anya na-emerụ emerụ na ntinye ụlọ. Akụrụngwa a na-ewepụta, na-eji ma nwee ike ịgbasa ike ugboro redio yana, ọ bụrụ na etinyeghị ya ma jiri ya soro ntuziaka a, nwere ike ibute ndabichi na-emerụ ahụ na nkwukọrịta redio. Agbanyeghị, enweghị nkwa na nnyonye anya agaghị eme na otu nrụnye. Ọ bụrụ na akụrụngwa a na-ebute nnyonye anya na-emerụ ahụ na nnabata redio ma ọ bụ telivishọn, nke enwere ike ikpebi site na ịgbanyụ ma gbanye akụrụngwa, a na-agba onye ọrụ ume ka ọ nwaa idozi nnyonye anya site na otu ma ọ bụ karịa n'ime usoro ndị a:

  • Megharịa ma ọ bụ bugharịa antenna nnata.
  • Mee ka nkewa dị n'etiti akụrụngwa na onye nnata.
  • Jikọọ akụrụngwa na ntinye na sekit dị iche na nke ejikọrọ onye nnata.
  • Kpọtụrụ onye na-ere ahịa ma ọ bụ onye ọrụ redio/TV nwere ahụmahụ maka enyemaka.

Nkwupụta Mkpughe FCC Radiation:
Ngwa a na-akwado oke ikpughe radieshon FCC nke edobere maka gburugburu ebe anaghị achịkwa ya. Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na opekempe 20 cm n'etiti radiator & ahụ gị. T-Ngosipụta-S3 AMOLED 1.91

  • Ụdị 1.0 Nwebiisinka © 2023

Akwụkwọ / akụrụngwa

LILYGO T Ngosipụta S3 AMOLED 1.91 Software [pdf] Ntuziaka onye ọrụ
T Ngosipụta S3 AMOLED 1.91 Software, S3 AMOLED 1.91 Software, AMOLED 1.91 Software, Software

Ntụaka

Hapụ ikwu

Agaghị ebipụta adreesị ozi-e gị. Akara mpaghara achọrọ akara *