LANCOM Systems ON-D8a Lancom AirLancer
gafereview of the mounting kit
- 1 connection flange (A)
- 1 connection arm (B)
- 1 pole flange / wall bracket (C)
- 4 washers M6 (D)
- 4 spring washers M6 (E)
- 4 nuts M6 (F)
- 1 pole clamp for pole diameter up to 62.5 mm (I)
- 2 hexagon head screws M8x35 (J)
- 4 spring washers M8 (K)
- 4 washers M8 (L)
- 2 nuts M8 (M)
- 2 hexagon head screws M8x70 (N)
Agụnyeghị ya na oke nnyefe
2 ìgwè clamps for pole diameter > 62.5 mm (H)
Mounting the antenna flange and connection arm
Screw the connection flange (A) to the back of the antenna housing using the enclosed washers (D), spring washers (E), and nuts (F). Make sure that the spring washers (E) are located directly under the nuts (F).
Then fasten the connection arm (B) hand-tight to the connection flange (A) using a screw (J), a spring washer (K), a washer (L), and a nut (M). Make sure that the spring washer (L) is located directly under the screw head.
Nkwadebe maka ịkwanye mgbidi
Ọ bụrụ na ịchọrọ ịkwanye antenna n'elu mgbidi, jiri mgbidi mgbidi (C) dị ka ihe na-emepụta ihe na-eme ka akara oghere maka mgbidi mgbidi.
Gwuo oghere ndị kwekọrọ na akara ma tinye dowels (anaghị etinye ya) n'ime ha ma ọ dị mkpa. Dabere na ihe mgbidi na ọnọdụ, omimi na dayameta nke oghere ga-edozi.
Ịgbanye mgbidi nke antenna
- Kwado mgbidi mgbidi ahụ na oghere ndị a na-egwupụta ihe ma jikọta ya na kposara kwesịrị ekwesị.
- Now hand-tighten the connection arm (B) already mounted on the connection flange (A) to the wall bracket (C) using a screw (J), a spring washer (K), a washer (L), and a nut (M).
- Make sure that the spring washer (K) is located directly under the screw head and that the arrow on the back of the antenna housing is pointing upwards.
- Hazie antenna ahụ dị ka ọchịchọ gị si dị wee mee ka skru nke ogwe aka njikọ jiri torque kwesịrị ekwesị sie ike.
Ogwe nrịgo nke antenna
Position the pole flange (C) at the desired height on a suitable pole with sufficient load-bearing capacity. Use the pole clamp (I) to attach to poles up to 62.5 mm in diameter.
- Fasten the pole clamp (I) to the pole flange (C) using the two screws (N), the spring washers (K), and the washers (L). Please note that the mast clamp must be rotated depending on the mast diameter.
- For pole diameters over 62.5 mm, you need suitable band clamps (H) (not included in the scope of delivery) and guide them through the pole flange and around the pole as shown in the overview
and tighten them after you have aligned the pole flange.
- Then connect the pole flange (C) hand-tight to the connection arm (B) already mounted on the antenna using an enclosed screw (J), a spring washer (K), a washer (L), and a nut (M).
- Make sure that the spring washer (K) is located directly under the screw head and that the arrow on the back of the antenna housing is pointing upwards.
- Hazie antenna dị ka ihe ị chọrọ wee mee ka skru nke ogwe aka njikọ jiri torque kwesịrị ekwesị sie ike.
Ozi dị mkpa
- Ịrụ ọrụ nke ukwuu ugboro ugboro
Iji rube isi n'iwu nchebe nke EU Directive 2014/53 na EN 62479 maka ihe mgbochi ndị bụ isi maka nchekwa nke ndị mmadụ na mpaghara elektrọnịkị na "FCC Policy on Human Exposure to Radiofrequency Electromagnetic Fields", ọ dị mkpa ịhazi. uru antenna ziri ezi na rawụta WLAN ma ọ bụ ebe ịnweta WLAN. - Iwu Ngwa eletriki na Eletrọnịkị
Biko etinyela ihe mkpofu eletriki na eletrọnịkị n'ime mkpofu ụlọ, ebe enweghị ike ịmegharị ya. Gbaa mbọ hụ na a na-ekpofu ọkụ eletrik na eletrọnịkị gị dịka ntuziaka obodo gị siri dị ugbu a. - Ijikwa eriri antenna ziri ezi
Igwe eriri antenna bụ eriri RF nwere mmetụta. Mgbe ị na-edobe ha, ọ dị mkpa iji hụ na eriri anaghị agbanye ma na-ehulata ntakịrị dị ka o kwere mee, n'ihi na nke a nwere ike ịkpata mfu n'ihe gbasara arụmọrụ antenna. N'otu aka ahụ, eriri antenna ekwesịghị ịnya n'ime loops siri ike. - Enweta antenna na nkwụsị nke ọdụ ụgbọ mmiri antenna ejighi ya na ebe nnweta
A ga-akwụsịrịrị njikọ antenna ejighị n'aka na ebe ị ga-enweta ya site na iji eriri mkpanaka akpọchiri akpọchi. Maka ebe ị ga-abanye n'ime ụlọ, enwere ike iji resistor na-akwụsị akwụsị gụnyere ihe nkwụnye AirLancer AN-RPSMA-NJ. Tụkwasị na nke ahụ, a ghaghị ịkọwa uru antenna na nhazi nke ebe ntinye.
Data teknụzụ
- Ugboro ugboro 4,900 - 5,900 MHz
Njirimara antenna
- Radiation patterns Horizontally: 8° Vertically: 8°
- Recommended use Point-to-Point
- VSWR 2.0:1 max.
- Gain 21 dBi max.
Data igwe
- Akụkụ (mm) 370 x 370 x 30 (W x H x D)
- Weight 1,800 g (Antenna without mounting kit)
- Okpomọkụ na-arụ ọrụ -40°C ruo 85°C
- Color Light grey
- Material UV resistant plastic
- Mounting options Wall- and pole mounting, alignable
- Cables & Connectors 2x 100 cm ULA100 cable with N-Plug connector
Ihe
- Akwụkwọ ikike afọ 2 maka AirLancer na ngwa
- Ihe mba. 61708
- Scope of delivery Antenna, 2 connection cables, mounting kit for wall and pole mounting
Ụlọ ọrụ LANCOM Systems GmbH
Ụlọ ọrụ Rohde & Schwarz Adenauerstr. 20/B2
52146 Wuerselen | Germany
info@lancom.de | lancom-systems.com
LANCOM, LANCOM Systems, LCOS, LANcommunity, LANCOM Service LANcare, LANCOM Active Radio Control, and AirLancer are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omis-
sions. 111436 09/2025
Ajụjụ a na-ajụkarị
Ajụjụ: Gịnị ka m ga-eme ma ọ bụrụ na akụkụ ụfọdụ na-efu na ngwugwu?
A: Kpọtụrụ nkwado ndị ahịa maka enyemaka iji nweta akụkụ ndị na-efu efu.
Q: How do I ensure proper alignment of the antenna during mounting?
A: Follow the provided instructions carefully and use appropriate tools to align the antenna as needed.
Akwụkwọ / akụrụngwa
 |
LANCOM Systems ON-D8a Lancom AirLancer [pdf] Akwụkwọ ntuziaka ON-D8a Lancom AirLancer, ON-D8a, Lancom AirLancer, Lancom, AirLancer |