Lambda CS-3000 Series Curve Tracer
Nkọwapụta
- Model: Curve Tracer CS-3000 series (CS-3100, CS-3200, CS-3300)
- Collector Supply (HV Mode): Max.Peak voltage – 3 kV, Max. Peak current – 15 A, Max. peak power – 390 W
- Collector Supply (HC Mode): Max.PPeakvoltage – 30 V, Max. peak current – 7.5 A, Pulse width – 50 us to 400 us
- Step Generator: Step rate – 1/10 Step, Pulse width range – 50 us to 400 us
- Ntụ: Onye nchịkọta voltage range – HV: 50 mV/div to 500 V/div, HC: 50 mV/div to 5 V/div
Ntuziaka ojiji ngwaahịa
Nkwanye onye nchịkọta
For HV mode, set the max. Peak voltage and current according to the specifications. For HC mode, adjust the settings as needed.
Nzọụkwụ Generator
Set the step rate and pulse width within the specified ranges for accurate measurements.
Ntụ
Jiri onye nchịkọta kwesịrị ekwesị voltage range based on the mode of operation for precise readings.
Ideal for measuring the characteristics of various semiconductors such as IGBTs, MOSFETs, transistors, and diodes etc.
- Kachasị elu voltage 3,000V (high voltage mode)
- Maximum peak current 1,000A (CS-3300 high current mode)
- All models equipped with LEAKAGE mode (1pA cursor resolution)
- USB port to save screen data and setup data
- Equipped with La LAN interface for remote control
Easy-to-understand measurement screen
CS-3000 Series Specifications
Collector supply HV mode
| Nlereanya | CS-3100-300V * 2 | CS-3100 / CS-3200 / CS-3300 | |||
|---|---|---|---|---|---|
| Ụdị/polarity | Full wave rectification/ + – , DC/ + – , LEAKAGE/ + – , AC | ||||
| Kachasị elu voltage | 300V | 30V | 3kV | 300V | 30V |
| Kachasị elu ugbu a (maximum peak pulse current * 1 ) |
750mA (1.5A * 1 ) |
7.5A (15A * 1 ) |
75mA (150mA * 1 ) |
750mA (1.5A * 1 ) |
7.5A (15A * 1 ) |
| Ike kacha elu | 120mW / 1.2W / 120W / 390W (Cannot be set when using the maximum peak voltage of 3kV) | ||||
| Horizontal axis range | 50mV～500V/div | ||||
- The maximum instantaneous current value that can be generated (varies depending on the target to be measured and conditions), the measurement should be less than or equal to the maximum peak current value.
Collector supply HC mode
| Nlereanya | CS-3100 / CS-3100-300V * 2 | CS-3200 | CS-3300 | |||
|---|---|---|---|---|---|---|
| Ụdị/polarity | Not equipped with HC mode | Pulse/ + – | ||||
| Kachasị elu voltage | 40V | |||||
| Kachasị elu ugbu a | 400A | 40A | 1,000A | 400A | 40A | |
| Ike kacha elu | 4kW | 400W | 10kW | 4kW | 400W | |
| Obosara usu | Pulse width is variable at 50µs to 400µs (10µs resolution) | |||||
| Ebe nlele | The measurement point can be specified (10µs resolution) | |||||
| Vertical axis range | 100mA～50A/div | 100mA～100A/div | ||||
| Nnwale ngwa ngwa | CS-301 | CS-302 | ||||
Nkọwapụtakarị
| Loop correction | Akụrụngwa | Correction ofthe floating capacitance between the collector supply and the ground | |
| Ngwa ngwa | Pseudo-looping through software optimisation | ||
| Ntụpụ generator | Akwụsịghị | Ntọala nso | -10 ～ +10 x STEP AMPLITUDE Setting |
| Mkpebi | 1% of the STEP AMPLITUDE setting | ||
| Ụdị dị ugbu a | Oke | 50nA to 200mA per step, 21 steps, 1-2-5 switching | |
| Kachasị ugbu a | 2A | ||
| Oke voltage | 10V ma ọ bụ karịa | ||
| Voltagna mode | Oke | 50mV to 2V per step, 6 steps, 1-2-5 switching | |
| Kachasị ugbu a | 500mA～(～8V), 200mA～(～15V), 10mA～(～40V) | ||
| Oke voltage | ± 40V | ||
| Ọnụego nzọụkwụ | 2x 50Hz or 60Hz (1x in AC mode), pulse interval in HC mode | ||
| Ụkwụ ụkwụ | Obosara usu | 50µs～400µs (10µs step) When in HC mode, the pulse width is 100µs wide before and after the pulse of the collector supply |
|
| Ọnụọgụ nke nzọụkwụ | 0～20 Step | ||
| Mmepụta AUX | Oke | OFF, -40V～+40V (Variable in 100mV steps) | |
| Ụkpụrụ nha | Tinyegharịa, Kwụsị/Na-alụbeghị Nwaanyị, Sụọ | ||
| Axis kwụ ọtọ (full scale 10div) |
Onye nchịkọta ugbu a | Oke | HV mode：1µA/div to 2A/div, 20 steps 1-2-5 switching (HC mode is not included) |
| Izi ezi | 2% + 0.05 x VERT/div of readout To this, add the loop correction error for the following maximum peak voltages 0.5µA(30V), 1µA(300V), 6µA(3kV), 12µA(5kV) Specify at least 10% of the maximum peak voltage for 30V, 300V, and 3kV, and at least 30% for 5kV |
||
| Emitter ugbu a (LEAKAGE) |
Oke | 1nA/div～2mA/div, 20 step 1-2-5 switching (Collector supply mode is LEAKAGE) |
|
| Izi ezi | 2% + 0.05 x VERT/div + 1nA or less of readout | ||
| Axis kwụ ọtọ (full scale 10div) |
Onye nchịkọta voltage |
Oke | HC mode：50mV/div to 5V/div, 7 steps 1-2-5 switching (HV mode is not included) |
| Izi ezi | 2% + 0.05 x HORIZ/div or less of readout | ||
| Base/ emitter voltage |
Oke | 50mV/div~5V/div, 7 step 1-2-5 switching | |
| Izi ezi | 2% + 0.05 x HORIZ/div or less of readout | ||
| Ngosipụta | Ngosipụta | 8.4-inch TFT LCD | |
| Ọnụọgụ nke akara data | 1,000 points/trace (AC, full wave rectification) 20～1,000 points/trace (SWEEP mode) |
||
| Trace display | Point interpolation display, dot display | ||
| Nkezi | OFF, 2 to 255 times | ||
| Nkwụsi ike | OFF, SHORT, LONG, Infinite length | ||
| Save internal waveform (REF) | 4-Ogwe | ||
| Cursor | DOT | Vert, Horiz, β or gm | |
| fLINE | Vert, Horiz, 1/grad, intercept | ||
| FREE | Vert, Horiz, β or gm | ||
| Window | Vert, Horiz, β or gm in the WINDOW area | ||
| Data save/read | Ebe nchekwa | Setup：256 pcs, REF：4 screens | |
| Ebe nchekwa mpụga | USB1.1：Setup, waveform, screen hardcopy (BMP, TIFF, PNG) | ||
| Ime ime | Equipped with a remote 10BASE-T/100BASE-TX 1 port via LAN connection | ||
| Ịnye ọkụ | AC100～240V 50/60Hz, Maximum operating power：500VA (400W), Standby：50VA (7W) | ||
| External dimensions(mm) Ibu |
CS-3100 / CS-3100-300V * 2 | Approx. 424W x 220H x 555D (excluding protrusions and accessories) approx. 28kg (excluding accessories) |
|
| CS-3200, 3300 | Approx. 424W x 354H x 555D (excluding protrusions and accessories) approx. 43kg (excluding accessories) |
||
CS-3100-300V is a made-to-order product.
Ngwa ngwa ọkọlọtọ
| CS-500 Nwalee nkwụnye | |
|---|---|
 |
This is a jig for connecting the part to be measured, provided by the customer, and the fixture. (Standard accessories) |
Ajụjụ
Ajụjụ: Kedu ihe m ga-eme ma ọ bụrụ na obosara usu dị oke warara?
A: If the pulse width is narrow, adjust the settings to widen it within the allowable range to generate the max. peak voltage.
Q: Kedu ka esi ahazi ihe mmepụta ihe na-anakọta?
A: The collector supply output can be calibrated by enabling/disabling the output and adjusting the floating capacity as per the instructions provided.
Akwụkwọ / akụrụngwa
 |
Lambda CS-3000 Series Curve Tracer [pdf] Akwụkwọ ntuziaka CS-3100, CS-3200, CS-3300, CS-3000 Series Curve Tracer, Curve Tracer, Tracer |