Keeson RC309B Remote Control User Manual

Keeson RC309B Remote Control

Nkọwapụta

• Aha ngwaahịa: Njikwa dịpụrụ adịpụ
• Ụdị: RC309B
• Ntinye: 2 x Battery AAA 1.5V
• Onye nrụpụta: Ụgwọ nke ụlọ ọrụ Keeson Technology Corporation Limited
• Manufacturing Country: China

Ntuziaka ojiji

Figure 1 illustrates the buttons on the remote control.

Isi elu

1. Press and hold the HEAD UP button of the remote, the head actuator moves out, stop when released.
2. Isi ala
   Press and hold the HEAD button of the remote, the head actuator moves in, stop when released.
3.  Were ụkwụ elu
   Press and hold the FOOT UP button of the remote, the foot actuator moves out, stop when released.
4. gbadaa
   Press and hold the FOOT button of the remote, the foot actuator moves in, stop when released.
5. Dị larịị
   Click the FLAT button, the bed goes flat, stop when you click any button during the process of going flat.
6. Isi ịhịa aka n'ahụ
   Click the MASSAGE HEAD button, head massage motor switches massage intensity, massage intensity switches among 0-1-2;
7. bọtịnụ ZG
   Click the ZG button, the actuator moves to the ZG position, stops when clicking any button, dilling the movement;
8. Memory Favorite position
   Clicking once will move the app to the Favorite position; long press to memorize the position, the backlight will flash twice, and releasing the button will continue the flashing.
9. Memory Fvorite2 position
   Clicking once will move the app to the Fav01ite2 position; long press to memorize the position, the backlight will flash twice, and releasing the button will continue the flashing.
10. Mkpọchi
    Press and hold the child lock button until the red light flashes twice, indicating that the child lock is successfully engaged. Dialing the locking process, pressing any button will cause the red light to flash for 2 seconds, indicating that the lock is engaged.

FCC:

FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to tlY to conect the interference by one or more of the following measures:

• Megharịa ma ọ bụ bugharịa antenna nnata.
• Mee ka nkewa dị n'etiti akụrụngwa na nnata.
• Jikọọ akụrụngwa n'ime oghere na sekit dị iche na nke ejikọrọ onye nnata.
• Kpọtụrụ onye na-ere ahịa ma ọ bụ onye ọkachamara redio-TV maka enyemaka.

Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ọrụ ahụ. Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:

1. Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ,
2. This device must accept any interference received, including interference that may cause undesired operation to accept any interference received.

Ozi ngosi RF

Atụlela ngwaọrụ a iji mezuo ihe achọrọ mkpughe RF izugbe. Enwere ike iji ngwaọrụ ahụ na ọnọdụ mkpughe na-enweghị mmachi.

ISED RSS ịdọ aka ná ntị:

This device complies with Innovation, Science and Economic Development Canada licence, exemplifying RSS standard(s). Operation is subject to the following two conditions:

• Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya.
• Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla, gụnyere nnyonye anya nwere ike bute ịrụ ọrụ ngwaọrụ a na-achọghị.

Nchọpụta nsogbu

If the remote control is not functioning as expected:

• Lelee batrị: Ensure that two AAA 1.5V batteries are correctly inserted and have sufficient charge.
• Mkpọchi nwa: If the remote is unresponsive and the red light flashes for 2 seconds when a button is pressed, the child lock may be engaged. Refer to section 1.7 to disengage the child lock.
• Ntinye aka: This device complies with FCC rules regarding interference. If you experience unexpected operation, it might be due to external interference. Ensure there are no strong radio frequency sources nearby.

Ajụjụ

• Kedu ka m ga-esi gbanwee batrị?
  The remote uses 2 x AAA 1.5V batteries. Open the battery compartment, remove the old batteries, and insert new ones, ensuring correct polarity.
• What does the ‘ZG’ button do?
  The ‘ZG’ button moves the bed to a pre-set Zero Gravity position, which is often considered an optimal position for comfort and pressure relief.
• Can I customize the ‘Favorite’ positions?
  Yes, you can memorize your preferred head and foot positions for both ‘Favorite 1’ and ‘Favorite 2’ by long-pressing the respective buttons.
• What should I do if the remote’s red light flashes when I press a button?
  If the red light flashes for 2 seconds when you press a button, it indicates that the child lock is engaged. You will need to disengage it to use the remote.
• Are there any restrictions on where I can use this device?
  This device has been evaluated for general RF exposure and can be used in portable exposure conditions without restriction.
• What if I make unauthorized changes to the equipment?
  Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị otu na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ngwa ahụ.