HYPERKIN Competitor Wired Controller User Manual

HYPERKIN Competitor Wired Controller

Daalụ maka ịzụrụasing the Hyperkin The Competitor for Xbox Series X|S, Xbox One, and Windows 10/11 PC – Wired Controller. For your safety and the safety of others, please carefully read this guide before using this product.

1. Plug the provided Type-C cable into the Type-C port located on the TOP of the Hyperkin Xenon.
2. Plug the other end of the cable into an available USB port on your Xbox Series X|S, Xbox One, PC or Steam OS.
3. The controller will vibrate.
4. Click the Nexus button.
5. The ring light will illuminate.

Onye njikwa gị adịla njikere iji.

WAKING UP YOUR XBOX CONSOLE USING THE COMPETITOR

If The Competitor is plugged into an Xbox console, you may turn on the console by clicking the Nexus button on The Competitor. After doing so, the console will turn on and the controller Nexus button will illuminate (this may take a few seconds).

Onye njikwa gị adịla njikere iji.

PROGRAMMABLE BACK BUTTONS (MAPPING)

To map a button to a back button, hold the Mode Button (marked “M”) on the back of the controller, and your desired back button (M1 or M2) at the same time. The Competitor will vibrate, and the ring light around the Nexus will begin to flash. Release the Mode Button and back button. The Competitor is now in “mapping mode”. Next, click the button you would like mapped to your desired back button. The Competitor will vibrate again, indicating that you have exited “mapping mode” and the selected button has been mapped to your desired back button.

PROGRAMMABLE BACK BUTTONS (UN-MAPPING)

To un-map a button from a back button, hold the Mode Button (marked “M”) and your desired back button. The Competitor will vibrate, and the ring light will begin to flash. Release the Mode Button and back button. The Competitor is now in “mapping mode”. Next, click the same back button. The Competitor will vibrate again, indicating that you have exited “mapping mode” and a button is no longer mapped to that back button.

BACK BUTTON LOCKS

To disable back buttons, slide the switches on the back of The Competitor inwards towards the “locked” indicator to lock the back buttons. Slide outwards to unlock.

REMOVEABLE STICK CAPS
Grip and remove the stick caps in an upward motion. To set new stick caps onto the sticks, align the smaller teeth on the stick caps with the notches on the stick. Press down on the stick caps until they click into place.

AKWKWỌ
Connect your headset audio jack into the bottom of The Competitor.

Bọtịnụ MIC MUTE
Double-tap the Mute Button (microphone symbol) on the front of The Competitor to mute the microphone on a connected headset. An orange glow indicates that your microphone is muted.

FCC ọkwa

A nwalere ngwa a wee hụ na ọ dabara na oke maka ngwaọrụ dijitalụ klaasị B, dabere na akụkụ 15 nke Iwu FCC. Emebere oke ndị a na ntinye ebe obibi. Akụrụngwa a na-ewepụta, na-eji, ma nwee ike ịgbasa ike ugboro redio yana, ọ bụrụ na etinyeghị ya ma jiri ya dịka ntuziaka siri dị, nwere ike ibute ndabichi na-emerụ ahụ na nkwukọrịta redio. Agbanyeghị, enweghị nkwa na nnyonye anya agaghị eme na otu nrụnye. Ọ bụrụ na akụrụngwa a na-ebute nnyonye anya na-emerụ ahụ na nnabata redio ma ọ bụ telivishọn, nke enwere ike ikpebi site na ịgbanyụ ma gbanye akụrụngwa, a na-agba onye ọrụ ume ka ọ nwaa idozi nnyonye anya site na otu ma ọ bụ karịa n'ime usoro ndị a:

• Megharịa ma ọ bụ bugharịa antenna nnata.
• Mee ka nkewa dị n'etiti akụrụngwa na nnata.
• Jikọọ akụrụngwa n'ime oghere na sekit dị iche na nke ejikọrọ onye nnata.
• Kpọtụrụ onye na -ere ahịa ma ọ bụ ọkachamara na redio TV ma ọ bụ email nwere ahụmahụ Nkwado@Hyperkin.com maka enyemaka. A ga -eji eriri echekwara ya na ngalaba a iji hụ na nrube isi na klaasị B FCC dị.

Mgbanwe ma ọ bụ mgbanwe na ngalaba a na-akwadoghị nke ọma nke ndị na-ahụ maka nnabata nwere ike imebi ikike onye ọrụ iji rụọ ọrụ a.

Nkwupụta nke nnabata na ntuziaka EU

Hyperkin Inc., located at 1939 West Mission Blvd, Pomona, CA 91766, declares under our sole responsibility that the product, Hyperkin Xenon Wired Controller, is in compliance with the essential requirements and other relevant provisions of Low Voltage Ntuziaka (LVD) 2014/35/EU, RoHS Ntuziaka 2011/65/EU, na-ebu akara CE.

Enwere ike ịrịọ Nkwupụta zuru oke nke Nkwekọ site na email:

• Email: compliance@hyperkin.com
• Aha Ụlọ Ọrụ: Ụlọ ọrụ Hyperkin Inc.
• adreesị: 1939 West Mission Blvd, Pomona, CA 91766

© 2026 Hyperkin Inc. Hyperkin® is a registered trademark of Hyperkin Inc. All rights reserved. All other trademarks are the property of their respective owners.