Ngwa HT HT10 Ogwe abụọ Voltage onye nyocha

Ozi ngwaahịa

Nkọwapụta

• Ụdị: HT10
• Mwepụta: 4.00 - 02/12/2024
• Asụsụ: Italiano, Bekee, Deutsch

Akpachara anya na usoro nchekwa

Ngwa a na-akwado IEC/EN61010-1. Maka nchekwa nke gị yana ka ịzenarị imebi akụrụngwa, a na-atụ aro ka idobe ntuziaka ndị dị n'akwụkwọ ntuziaka a wee jiri nlezianya gụọ ndetu niile bu akara n'ihu. 

kpachara anya

• Dabere n'ime impedance nke voltage detector a ga-enwe ike dị iche iche nke na-egosi na ọnụnọ ma ọ bụ enweghị ọrụ voltage bụrụ na nnyonye anya voltage di
• A voltage detector nke dịtụ ala ime impedance, ma e jiri ya tụnyere uru ntụaka nke 100k, agaghị egosi niile nnyonye anya vol.tages inwe mbụ voltage uru karịa ọkwa ELV. Mgbe enwere kọntaktị na akụkụ ndị a ga-anwale, voltage detector nwere ike wepu nnyonye anya nwa oge voltage ruo ọkwa dị n'okpuru ELV, mana voltage ga-alaghachi na uru mbụ mgbe voltage wepụ ihe nchọpụta
• Mgbe ihe ngosi “voltage present” apụtaghị, a na-atụ aro ka ịwụnye akụrụngwa earthing tupu ịga n'ihu
• A voltage detector nke dịtụ elu esịtidem impedance, ma e jiri ya tụnyere uru ntụaka nke 100k, nwere ike ọ gaghị ekwe ka gosi n'ụzọ doro anya na-anọghị nke ọrụ voltaji.tage bụrụ na nnyonye anya voltage di
• Mgbe ihe ngosi “voltage present” na-egosi n'akụkụ a na-atụ anya na a ga-ekewapụ na nrụnye, a na-atụ aro ya nke ukwuu site n'ụzọ ndị ọzọ (dịka ọmụmaatụ iji volta ọzọ).tage detector, visual check of the disconnected parts of the electric circuit to test , etc.) na ọ dịghị arụ ọrụ vol.tage n'akụkụ a ga-anwale na ikwubi na voltage gosiri site na voltage detector bụ nnyonye anya voltage
• A voltage detector na-ekwupụta ụkpụrụ abụọ nke impedance ime agafeela ule arụmọrụ nke ịchọpụta nnyonye anya voltages na (n'ime oke teknụzụ) nwere ike ịmata ọdịiche ọrụ voltage sitere na nnyonye anya voltage ma nwee ụzọ isi gosi kpọmkwem ụdị voltage di
• Emebere ngwa a maka ojiji na gburugburu nwere ogo mmetọ 2.
• Enwere ike iji ya maka DC na AC VOLTAGE nha na nrụnye nke CAT IV 600V ma ọ bụ CAT III 1000V

A na-eji akara ndị a na ngwa:

Kpachara anya - rụtụ aka na ntuziaka ntuziaka - iji na-ezighi ezi nwere ike imebi ngwa ma ọ bụ akụkụ ya
Mkpuchi okpukpu abụọ
DC Voltage
AC Voltage
Ngwa kwesịrị ekwesị maka ịrụ nha n'okpuru voltage
Ngwa ahụ na-agbaso iwu nke TÜV Association maka Eletriki, Eletrọnịkị & Teknụzụ Ozi yana iwu nke Geprüfte Sicherheit.
Kpachara anya: akara a na-egosi na akụrụngwa, batrị, na ngwa ya ga-edobere nchịkọta dị iche na mkpofu ziri ezi.

N'oge eji
Debe ntuziaka ndị dị n'akwụkwọ ntuziaka a mgbe niile:

• Mgbe ị na-eji ngwá ọrụ ahụ, na-asọpụrụ ụkpụrụ nchekwa ndị a na-emebu iji chebe gị pụọ na mmiri ọkụ eletrik dị ize ndụ yana ngwa ahụ megide ọrụ na-ezighi ezi.
• Anwalela ma ọ bụ jikọọ na sekit ọ bụla gafere nchebe oke ibu akọwapụtara
• Ejila nha n'okpuru ọnọdụ gburugburu ebe obibi gafere oke egosiri na § 7.2
• Lelee ọnọdụ batrị dị n'ime tupu ejiri ya ma dochie ha ma ọ bụrụ na ọ dị mkpa
• Tupu eji ya hụ na arụ ọrụ akụrụngwa zuru oke (dịka na voltage isi iyi)
• A ghaghị ịlele ọrụ nke ngwa ngwa ngwa ngwa tupu iji ya na mgbe ejiri ya site na iji nyocha nyocha. Ọ bụrụ nrịbama nke otu usoro ma ọ bụ karịa daa ma ọ bụ ọ bụrụ na enwetaghị ọrụ ọ bụla, agakwaghị eji ngwa ahụ.
• Agaghị eji akara ngosi dị iche iche gosipụtara na ngwa (gụnyere akara oke ELV) maka ebumnuche atụ.
• Tupu iji ngwá ọrụ nwere ihe nrịbama a na-anụ n'ebe ndị nwere ọkwa mkpọtụ dị elu, biko nyochaa ma ọ bụrụ na a na-ahụta mgbama a na-anụ.
• Dobe ngwa ahụ ka ịzenarị izochi ihe ngosi anya ma ọ bụ mkpuchi ụda mgbasa ozi
• Lelee ọnọdụ nke voltage isi iyi tupu iji ngwá ọrụ

MGBE eji ya
Ọ bụrụ na ị na-atụ anya na ị gaghị eji ngwa ahụ ogologo oge wepụ batrị

kpachara anya
Enweghị nnabata na CAUTIONs na/ma ọ bụ ntuziaka ahụ nwere ike imebi ihe nnwale na/ma ọ bụ ihe mejupụtara ya ma ọ bụ merụọ onye ọrụ ahụ ahụ.

NKWUKWU ỤWA ỤWA
Iwu TS EN 61010-1 / 1: Iwu nchekwa maka akụrụngwa eletriki maka nha, njikwa na iji ụlọ nyocha - Nkebi XNUMX: Ihe ndị chọrọ n'ozuzu ya na-akọwapụta ụdị nha, nke a na-akpọkarị overvol.tage ngalaba, bụ. Na § 6.7.4: Atụ sekit, ọ na-ekwu: (OMISSIS)
E kewara sekit n'ime usoro nha ndị a:

• Ụdị ntule IV bụ maka nha emere na isi iyi nke obere voltage echichi
• Examples bụ mita ọkụ eletrik na nha na ngwaọrụ nchebe nke mbụ na ngalaba njikwa ripple
• Ụdị nha III bụ maka nha ndị a na-eme na ntinye ụlọ
• Examples bụ nha na bọọdụ nkesa, ndị na-agbaji sekit, wiring, gụnyere eriri, bọsbars, igbe njikọ, switches, oghere n'ime nrụnye a kapịrị ọnụ, yana akụrụngwa maka iji ụlọ ọrụ na ụfọdụ akụrụngwa ndị ọzọ, maka ex.ample, moto na-anọ ọdụ na-adịgide adịgide njikọ na ofu echichi.
• Nkeji nleta II bụ maka nha emere na sekit ejikọrọ ozugbo na obere voltage nwụnye Examples bụ nha na ngwa ụlọ, ngwaọrụ mkpanaka na ngwa ndị yiri ya.
• Atiri I bụ maka nha emere na sekit na-ejikọghị ya na MAINS ozugbo
• Examples bụ nha na sekit esiteghị na MAINS, yana sekit echekwabara (ime ime) MAINS enwetara. N'okwu nke ikpeazụ, nrụgide na-agafe agafe na-agbanwe; n'ihi nke ahụ, ụkpụrụ na-achọ ka onye ọrụ mara ikike nke ngwa ngwa na-agafe agafe

Nkowa Izugbe

Ngwa ahụ na-eme nha ndị a:

• DC Voltage nwere usoro waya 2
• AC Voltage nwere usoro waya 2
• AC Voltage nwere usoro waya 1 (nchọpụta polarity)
• AC Voltage nha na obere impedance uru
• Ngosipụta usoro usoro
• Nleta mgbochi
• Nnwale ịga n'ihu na buzzer

A na-egosiputa nsonaazụ nha yana ngosipụta nke nkeji nha ma n'ụdị ọnụọgụ yana na ngosipụta LCD. Igwe ọkụ na-acha ọcha na-adịkwa ka ọ na-eme ule ahụ nke ọma ọbụlagodi na gburugburu ọkụ na-adịghị mma

Nkwadebe maka ojiji

Nlele mbụ
A na-enyocha ngwa ahụ site na igwe na igwe eletrik view tupu mbupu. A na-elezi anya ọ bụla iji hụ na akụrụngwa ruru gị n'ọnọdụ zuru oke. Agbanyeghị, ọ dị mma ka ịme nyocha ngwa ngwa iji chọpụta mmebi ọ bụla nwere ike ime na mbufe. Ọ bụrụ na ọ dị otu a, tinye ngwa ngwa n'aka onye na-ebu ebu. Gbaa mbọ hụ na ngwa niile edepụtara na § 7.3.1 dị na ngwugwu. Ọ bụrụ na ọ dị iche, kpọtụrụ onye na-ere ahịa gị. Ọ bụrụ na ị ga-alaghachite onye nyocha, biko debe ntuziaka enyere na § 8

ỊNYE ỌKỤ
A na-akwado ngwa ahụ site na batrị alkaline 2 × 1.5V ụdị AAA LR03. Mgbe batrị dị obere, a na-egosi batrị dị ala " "egosiri. Iji dochie batrị biko soro ntuziaka nke § 6.2

Nchekwa
Mgbe oge nchekwa dị n'okpuru ọnọdụ gburugburu ebe obibi dị oke egwu gafere oke a kpọtụrụ aha na § 7.2 ka ngwá ọrụ ahụ laghachi na ọnọdụ nha nkịtị tupu iji ya.

AHRC AKW .KWỌ

Nkọwapụta akụrụngwa

1. L1 nyocha dị ike
2. L2 nyocha nke edobere
3. Ihe nrịbama ọkụ LED
4. LEDs ịdọ aka ná ntị
5. Ngosipụta LCD
6. Mgbanwe ule impedance dị ala
7. igodo
8. igodo
9. Ngalaba batrị
10. Ihe mkpuchi batrị
11. Okpu nchebe n'ọnụ nyocha
12. 4mm metal aka uwe na esịtidem eri
13. Nchọpụta n'ọnụ nchebe mkpuchi

 Nkọwa nke LEDs ịdọ aka ná ntị

1. LED maka voltage ule
2. LED maka ule impedance dị ala
3. LED maka continuity ule
4. LEDs maka ule usoro usoro
5. LED maka AC voltage
6. LED maka DC voltage akara
7. LED maka ịdọ aka ná ntị voltage
8. Ngosipụta LCD

Nkọwa Ngosipụta

1. Ọrụ HOLD data agbanyere
2. voltagihe karịrị 50VAC/120VDC
3. Akara usoro usoro
4. Ngosipụta batrị dị ala
5. Ngosipụta LCD
6. Voltage na ngalaba mgbochi
7. DC/AC Voltage jikoro na polarity

Ntuziaka ịrụ ọrụ

Nwepu ikike izizi
Tupu ịmalite nha ọ bụla, mee nyocha ndị a

kpachara anya

• Jiri ngwa na volta mara amatage isi iyi
• Ihe "Ikanam na-agbanye mgbe voltage n'elu 50VAC/120VDC etinyere, ọ bụrụgodị na batrị dị ala ma ọ bụ na ewepụrụ ya
• Tupu na mgbe eji ngwá ọrụ mkpụmkpụ, L1 na L2 nyocha maka ihe ruru. 4-6 nkeji. Ekwesịrị ịdebe omume ndị a:
  • Igwe ọkụ niile ma e wezụga mgbanaka ule impedance dị ala
  • Mgbama a na-anụ ga-ada ụda
  • Agbanye akụkụ niile nke ngosi yana ọkụ azụ

DC VOLTAGE AKWỤKWỌ

kpachara anya

• Ntinye kachasị maka DC Voltage bụ 1000V. Atụla voltaji dị elutages iji zere ihe egwu nke mkpọ ọkụ eletrik ma ọ bụ mmebi dị egwu nke ngwaọrụ ahụ
• Ikanam ịdọ aka ná ntị na-agbanye na ụda buzzer maka voltage n'etiti nyocha ihe karịrị 120V

1. Mee ọrụ Autotest izizi (lee § 5.1)
2. Jikọọ nyocha L1 na L2 na ihe a na-anwale (lee foto 4). A na-eme nha ahụ naanị site na kọntaktị nke nyocha ozugbo na akụkụ ọla nke ndị na-eduzi
3. Ngwa na-agbanye na-akpaghị aka maka voltage> 6V na DC voltage uru na-egosipụta ma site red ikanam ịmafe na na ngosi. A na-egosipụta akara DC na "+" ọkụ ọkụ
4. Kwesịrị igosi “-” ọ pụtara na voltage nwere uzo ozo ma e jiri ya tụnyere njikọ egosiri na Fig 4
5. Ngwa ahụ na-agbanyụ na-akpaghị aka ozugbo ebipụrụ nyocha na ihe a na-anwale
6. Pịa igodo iji mee ka / gbanyụọ ọrụ HOLD na ngosi. Pịa ma jide igodo iji mee ka/gbanyụọ ìhè azụ ngosi
7. Pịa  igodo iji rụọ ọrụ/gbanyụọ ọwa LED ọcha

AC VOLTAGE AKWỤKWỌ

kpachara anya

• Ntinye kachasị maka AC Voltage bụ 1000V. Atụla voltaji dị elutages iji zere ihe egwu nke mkpọ ọkụ eletrik ma ọ bụ mmebi dị egwu nke ngwaọrụ ahụ
• Ikanam ịdọ aka ná ntị na-agbanye na ụda buzzer maka voltage n'etiti nyocha ihe karịrị 50V

1. Mee ọrụ Autotest izizi (lee § 5.1)
2. Jikọọ nyocha L1 na L2 na ihe a na-anwale (lee foto 5). A na-eme nha ahụ naanị site na kọntaktị nke nyocha ozugbo na akụkụ ọla nke ndị na-eduzi
3. Ngwa na-agbanye na-akpaghị aka maka voltage> 6V na AC voltage uru na-egosipụta ma site red ikanam ịmafe na na ngosi. Egosiri akara AC
4. Igwe ọkụ LED na “AC” mgba ọkụ, AC voltagA na-egosiputa nha, yana mgbama ụda na-apụta
5. Ngwa ahụ na-agbanyụ na-akpaghị aka ozugbo ebipụrụ nyocha na ihe a na-anwale
6. Maka nha na otu-phase osisi na LEDs nwere ike ịgbanwuo Nke a abụghị nsogbu ngwaọrụ
7. Pịa igodo iji mee ka ọrụ HOLD dị na ngosi. Pịa ma jide igodo iji mee ka/gbanyụọ ìhè azụ ngosi
8. Pịa  igodo iji rụọ ọrụ/gbanyụọ ọwa LED ọcha

AC VOLTAGE nwere ọnụ ahịa achụmnta ego dị ala

kpachara anya

• Ntinye kachasị maka AC Voltage bụ 1000V. Atụla voltaji dị elutages iji zere ihe egwu nke mkpọ ọkụ eletrik ma ọ bụ mmebi dị egwu nke ngwaọrụ ahụ
• Ikanam ịdọ aka ná ntị na-agbanye na ụda buzzer maka voltage n'etiti nyocha ihe karịrị 50V
• Ọrụ a bara uru karịsịa maka nrụnye nnwale. N'ihi mbelata nke ime ime, capacitive voltage mmetụta na-ebelata. Ọgụgụ ahụ na-egosi voltage tinye. N'otu aka ahụ, usoro nha (L1) na waya ụwa (PE) nwere ike ịkpalite ndị na-emebi sekit ugbu a (RCD)

1. Mee ọrụ Autotest izizi (lee § 5.1)
2. Jikọọ nyocha L1 na L2 na ihe a na-anwale (lee foto 6). A na-eme nha ahụ naanị site na kọntaktị nke nyocha ozugbo na akụkụ ọla nke ndị na-eduzi
3. Igwe ọkụ LED na “AC“ ihe mgba ọkụ, AC voltagA na-egosipụta nha ma na-ewepụta akara ngosi
4. Pịa mgba ọkụ abụọ (lee Fig. 1 - akụkụ 6) n'otu oge. Nke etinyere voltage na-egosipụta ma site na-acha uhie uhie LEDs ịmafe na na ngosi. Egosiri akara AC. LED maka ule impedance dị ala (lee Fig. 2 - akụkụ 2) na-agbanye
5. Ngwa ahụ na-agbanyụ na-akpaghị aka ozugbo ebipụrụ nyocha na ihe a na-anwale
6. Maka nha na otu-phase osisi na LEDs nwere ike ịgbanwuo. Nke a abụghị nsogbu ngwaọrụ
7. Pịa igodo iji mee ka/gbanyụọ ọrụ HOLD na ngosi. Pịa ma jide igodo iji mee ka/gbanyụọ ìhè azụ ngosi
8. Pịa  igodo iji rụọ ọrụ/gbanyụọ ọwa LED ọcha

1-WIRE AC VOLTAGNchọpụta E (POLARITY)

kpachara anya

• Ntinye kachasị maka AC voltage bụ 1000V. Agbalịla ịtụ elu voltages iji zere ihe egwu nke mkpọ ọkụ eletrik ma ọ bụ mmebi dị egwu nke ngwaọrụ ahụ
• 1-waya AC voltage kwesịrị iji e mode mee ihe dị ka ule ngwa ngwa iji chọpụta ọnụnọ voltage naanị na-egosighi nsonaazụ ọ bụla. Nnwale osisi adịghị mma iji chọpụta voltage. Maka nke a, ogwe osisi abụọ voltage ule bụ iwu mgbe niile
• Mgbe ị na-eji ule otu otu osisi iji chọpụta ndị na-eduzi mpụga, ọrụ ngosi nwere ike imebi n'okpuru ọnọdụ ụfọdụ (dịka ọmụmaatụ maka mkpuchi ahụ, akụrụngwa nchebe na ebe mkpuchi, wdg.
• Ikanam ịdọ aka ná ntị na-agbanye na ụda buzzer maka voltage n'etiti nyocha ihe karịrị 100V

1. Mee ọrụ Autotest izizi (lee § 5.1)
2. Jikọọ nyocha L2 na ihe a na-anwale (lee foto 7). A na-eme nha ahụ naanị site na kọntaktị nke nyocha ozugbo na akụkụ igwe nke onye nduzi
3. Igwe ọkụ LED na “- – -“ mgba ọkụ egosi, na mgbama ụda na-ewepụta maka voltagọ dị ugbu a> 100V AC
4. Ngwa ahụ na-agbanyụ na-akpaghị aka ozugbo ebipụrụ nyocha na ihe a na-anwale
5. Pịa igodo iji mee ka/gbanyụọ ọrụ HOLD na ngosi. Pịa ma jide igodo iji mee ka/gbanyụọ ìhè azụ ngosi
6. Pịaigodo iji rụọ ọrụ/gbanyụọ ọwa LED ọcha

Ngosipụta usoro usoro

kpachara anya

• Ntinye kachasị maka AC voltage bụ 1000V. Agbalịla ịtụ elu voltages iji zere ihe egwu nke mkpọ ọkụ eletrik ma ọ bụ mmebi dị egwu nke ngwaọrụ ahụ
• Ikanam ịdọ aka ná ntị na-agbanye na ụda buzzer maka voltage n'etiti nyocha ihe karịrị 50V

1. Mee ọrụ Autotest izizi (lee § 5.1)
2. Jikọọ nyocha L1 na oge L1 na nyocha L2 na usoro L2 nke usoro usoro atọ n'okpuru ule (lee Fig. 8). A na-eme nha ahụ naanị site na kọntaktị nke nyocha ozugbo na akụkụ ọla nke ndị na-eduzi
3. Igwe ọkụ LED na “AC“ ihe mgba ọkụ, AC voltagA na-egosipụta nha ma na-ewepụta akara ngosi
4. Nke A na-egosipụta akara (n'akụkụ elekere) ma ọ bụrụ na egosi usoro usoro ziri ezi. Nke  A na-egosipụta akara (wise elekere) ma ọ bụrụ na egosighi usoro usoro na-ezighi ezi
5. Jikọọ nyocha L1 na oge L2 yana nyocha L2 na usoro L3 nke usoro atọ n'okpuru ule. Nke A na-egosipụta akara (n'akụkụ elekere) ma ọ bụrụ na egosi usoro usoro ziri ezi. Akara A na-egosipụta (wise elekere) ma ọ bụrụ na egosighi usoro usoro na-ezighi ezi
6. Jikọọ nyocha L1 na oge L3 yana nyocha L2 na usoro L1 nke usoro atọ n'okpuru ule. Akara (n'aka elekere) na-egosipụta ma ọ bụrụ na egosi usoro usoro ziri ezi. Akara A na-egosipụta (wise elekere) ma ọ bụrụ na egosighi usoro usoro na-ezighi ezi
7. Pịa igodo iji mee ka/gbanyụọ ọrụ HOLD na ngosi. Pịa ma jide igodo iji mee ka/gbanyụọ ìhè azụ ngosi
8. Pịa igodo iji rụọ ọrụ/gbanyụọ ọwa LED ọcha

Nọgide na-anwale

kpachara anya
Tupu ịme ule na-aga n'ihu, wepụ ike na sekit n'okpuru ule wee wepụ capacitors niile

1. Mee ọrụ Autotest izizi (lee § 5.1)
2. Jikọọ nyocha L1 na L2 na ihe a na-anwale (lee foto 9)
3. Nnwale na-aga n'ihu na-arụ ọrụ maka nguzogide <400kΩ. Igwe ọkụ na-agbanye ọkụ na-akpaghị aka na LED" ", a na-egosipụta ozi "Con" na ụda na-ada ụda na-egosi ule dị mma
4. Mita na-agbanye na-akpaghị aka mgbe ekewapụrụ nyocha abụọ na ihe atụnyere
5. Pịa  igodo iji rụọ ọrụ/gbanyụọ ọwa LED ọcha

NJỤTA Nguzogide

kpachara anya
Tupu ewere ihe ọ bụla na nguzogide sekit, wepụ ike na sekit a ga-anwale wee wepụ capacitors niile

1. Mee ọrụ Autotest izizi (lee § 5.1)
2. Pịa ma jide  igodo iji gbanye akụrụngwa A na-egosipụta akara “OL” na “Ω”.
3. Jikọọ nyocha L1 na L2 na ihe a na-anwale (lee foto 10). Egosiri uru nguzogide na ngosi
4. Pịa igodo iji mee ka / gbanyụọ ọrụ HOLD na ngosi. Pịa ma jide igodo iji mee ka/gbanyụọ ìhè azụ ngosi
5. Pịa igodo iji rụọ ọrụ/gbanyụọ ọwa LED ọcha
6. Pịa ma jide igodo iji gbanyụọ ngwá ọrụ

Nkwadebe

Ozi Izugbe

1. Iji kwe nkwa ịrụ ọrụ akụrụngwa hụ na ị ga-eji ya ma ọ bụ dobe ya n'okpuru ọnọdụ gburugburu ebe kwesịrị ekwesị
2. Ewepụla ya na oke okpomọkụ ma ọ bụ iru mmiri ma ọ bụ ìhè anyanwụ kpọmkwem. Biko gbaa mbọ hụ na ịgbanyụ ya ma emechaa.
3. Ọ bụrụ na ị na-atụ anya na ị gaghị eji ngwa ahụ ogologo oge wepụ batrị ka ị ghara ịwepu mmiri mmiri batrị nke nwere ike imebi ihe dị n'ime ya.
4. Naanị ndị ikike ka a na-ahapụ ka ịkwasa ngwa ahụ

Ndochie batrị
Mgbe akara “ ” ka egosiri na ngosi dochie batrị.

kpachara anya
Naanị ndị ọkachamara nwere nkà nwere ike imeghe ngwa ma dochie batrị. Tupu iwepu batrị, kwụpụ ụzọ nnwale site na sekit ọ bụla na-enye ume iji zere ujo eletrik

1. Wepụ ihe nkedo na akụkụ ala nke ngwá ọrụ (lee Fig. 1 - akụkụ 10) ma wepụ ihe mkpuchi batrị.
2. Wepu batrị n'akụkụ batrị
3. Fanye batrị ọhụrụ nke otu ụdị (lee § 7.2) gbasara polarity egosiri (lee foto 11)
4. Weghachite mkpuchi batrị ma mesie nkedo ahụ ọzọ
5. Atụbakwala batrị ndị ejirila n'ime gburugburu mgbe ejiri ya. Jiri usoro mkpofu batrị kwesịrị ekwesị dị na mpaghara gị

ihicha
Maka ihicha ngwa, jiri akwa akọrọ dị nro. Ejila akwa mmiri, ihe mgbaze ma ọ bụ mmiri, wdg

Nkọwapụta nka nka

 AKWỤKWỌ NGWA NKE
A gbakọrọ izi ezi dị ka ±[%rdg + (dgt * mkpebi)] na 23°C±5°C, <70%RH

AC/DC Voltage (Ngosipụta LED)
Oke	Mkpebi	Izi ezi
12V ¸ 1000V	± 12, 24, 50, 120, 230, 400, 690, 1000V	na-akwado IEC/EN61243-3:2014

• Oke ugboro: 0/40Hz ÷ 400Hz
• Oge nzaghachi: 1s
• Ike akpaaka ON: ≥12V AC/DC
• Ogologo oge: mgbe 30s nke ịga n'ihu nha, ngwa ahụ chọrọ oge mgbake nke 240s tupu ọ malite nha ọhụrụ.

AC/DC Voltage (Ngosipụta LCD) - Autorange
Oke	Mkpebi	Izi ezi	Nchekwa oke ibu
6V ÷ 1000V	1V	± (3.0%rdg+5dgt)	1000VAC/DC

• Oke ugboro: 0/40Hz ÷ 400Hz
• Oge nzaghachi: ≤1s
• Ike akpaaka ON: ≥ 6V AC/DC
• Nhọrọ oke nha: akpaka
• Mgbochi ibu: 350kΩ / Is <3.5mA (enweghị mgbagha RCD)
• Ọnụ kacha elu ugbu a: max 3.5mA @ 1000V
• Ogologo oge: 30s
• Oge mgbake: 240s

AC Voltage nwere ọnụ ala impedance
Oke	Mkpebi	Oke ugboro	Nchekwa oke ibu
6V ÷ 1000V	1V	0/40Hz ÷ 400Hz	1000VAC/DC

• Ntinye ntinye: ca 7kΩ
• Ihe nrụpụta kacha ugbu a: Bụ (ibu) = 150mA
• Ntugharị RCD: ca 30mA @230V

1–wire AC voltage detection (polarity)
Oke	Mkpebi	Oke ugboro	Nchekwa oke ibu
100V ¸ 1000V	1V	50Hz ÷ 400Hz	1000VAC/DC

Nnwale na-aga n'ihu
Ọrụ	Buzzer	Nwalee ugbu a	Nchekwa oke ibu
	<400kΩ	<5µA	1000V AC / DC

Nleta mgbochi
Oke	Mkpebi	Izi ezi	Nchekwa oke ibu
0Ω ÷ 1999W	1Ω	± (5.0%rdg+10dgt)	1000V AC / DC
Nwalee ugbu a:	<30µA

Ngosipụta usoro usoro
Voltage oke	Oke ugboro	Nchekwa oke ibu
100V ¸ 1000V	50Hz ÷ 60Hz	1000VAC/DC

Usoro nha: 2-waya na kọntaktị na metal ndụ akụkụ

 IHE MMADỤ N'ỤWA

Ntuziaka ntụaka

• Safety: IEC/EN61010-1, IEC/EN61243-3:2014
• EMC: IEC/EN61326-1
• Mkpuchi: mkpuchi okpukpu abụọ
• ogo mmetọ: 2
• Ụdị nha: CAT III 1000V, CAT IV 600V

Ngosipụta

• Njirimara: 3½ LCD (ọnụọgụ 1999), akara nkeji iri, ọkụ azụ
• Ngosipụta oke oke: akara "OL" na ngosi
• Ụdị ntụgharị: Uru pụtara

Ịnye ọkụ

• Ụdị batrị: 2×1.5V ụdị batrị AAA LR03
• Ngosipụta batrị dị ala: akara " "na ngosi
• Gbanyụọ ike akpaaka: mgbe nkeji 1 gachara (ihe R)

Njirimara igwe

• Akụkụ (L x W x H): 270 x 70 x 30mm (11 x 3 x 1in)
• Ibu (gụnyere batrị): 290g (10ounces)
• Nchekwa igwe: IP64

Ọnọdụ gburugburu ebe obibi

• Okpomọkụ ntụaka: 23°C ± 5°C (73°F ± 41°F)
• Ọkụ na-arụ ọrụ: -10°C ÷ 55°C (14°F ÷ 131°F)
• iru mmiri na-arụ ọrụ: <85% RH
• Okpomọkụ nchekwa: -10°C ÷ 60°C (14°F ÷ 140°F)
• iru mmiri nchekwa: <85% RH
• Oke ogo ojiji: 2000m (6.562ft)

Ngwa a na-emeju ihe achọrọ nke Low Voltage Ntuziaka 2014/35/EU (LVD) na nke EMC Ntuziaka 2014/30/EU
Ngwa a na-egbo mkpa nke European Directive 2011/65/EU (RoHS) na 2012/19/EU (WEEE)

Ngwa ngwa

Ngwa ngwa ọkọlọtọ

• Nchedo plastik nke ihe nyocha ígwè
• Ihe nkwụnye aka uwe igwe 4mm + nchebe ọnụ, 2px Cod. KITHT10
• Batrị (anaghị etinye ya)
• Na-ebu akpa
• Akwụkwọ ntuziaka onye ọrụ

OZI

Ọnọdụ ikike
A na-ekwe nkwa akụrụngwa a megide mmejọ ihe ma ọ bụ mmebi mmepụta, dịka ọnọdụ ahịa izugbe si dị. N'ime oge ikike (otu afọ), enwere ike dochie akụkụ ndị ezighi ezi. Onye nrụpụta ahụ nwere ikike ikpebi ma ọ ga-arụkwa ma ọ bụ dochie ngwaahịa ahụ. Ọ bụrụ na ịlaghachite ngwá ọrụ, onye ahịa ga-akwụrịrị ụgwọ njem niile. Ngwa a ga-esonyere ya na ndetu nnyefe na-egosi mmejọ ma ọ bụ ihe kpatara nloghachi. Ihe nleba anya eweghachi ga-eburịrị n'ime igbe mbụ ya. Ihe mmebi ọ bụla mere na njem n'ihi enweghị nkwakọ ngwaahịa mbụ ga-akwụ onye ahịa ụgwọ. Ọ bụghị onye nrụpụtara maka mmebi ọ bụla megide mmadụ ma ọ bụ ihe. Ejighị akwụkwọ ikike kpuchie ngwa na batrị.
Agaghị etinye akwụkwọ ikike maka ikpe ndị a:

• Mmejọ n'ihi iji akụrụngwa eme ihe na-ezighi ezi
• Mmejọ n'ihi nchikota ihe nnwale na akụrụngwa na-adakọghị.
• Mmejọ n'ihi nkwakọ ngwaahịa na-ezighi ezi.
• Mmejọ n'ihi ọrụ nke onye ụlọ ọrụ enyeghị ikike mere.
• Mmejọ n'ihi mgbanwe ndị emere na-enweghị ikike doro anya nke ngalaba nka nka anyị.
• Mmejọ n'ihi mmegharị na otu ngwa ewepụtaghị site na nkọwa nke akụrụngwa ma ọ bụ site na ntuziaka ntuziaka.

Enweghị ike ịmegharị ọdịnaya nke akwụkwọ ntuziaka a n'ụdị ọ bụla na-enweghị ikike anyị.

Ngwaahịa anyị bụ patented. Edebara aha akara ngosi anyị. Anyị na-edobe ikike ịgbanwe àgwà na ọnụ ahịa n'ihu maka mmepe teknụzụ

OZI
Ọ bụrụ na akụrụngwa anaghị arụ ọrụ nke ọma, tupu ịkpọtụrụ ọrụ ahụ, nwalee batrị, ụzọ nnwale, wdg, wee gbanwee ha ma ọ bụrụ na ọ dị mkpa. Ọ bụrụ na akụrụngwa ahụ anaghị arụ ọrụ, gbaa mbọ hụ na usoro ọrụ gị dabara nke akọwara n'akwụkwọ ntuziaka a. Ọ bụrụ na ịlaghachite ngwá ọrụ, onye ahịa ga-akwụrịrị ụgwọ njem niile. Ngwa a ga-esonyere ya na ndetu nnyefe na-egosi mmejọ ma ọ bụ ihe kpatara nloghachi. Ihe nleba anya eweghachi ga-eburịrị n'ime igbe mbụ ya. Ihe mmebi ọ bụla mere na njem n'ihi enweghị nkwakọ ngwaahịa mbụ ga-akwụ onye ahịa ụgwọ

FIGURE INTERNEM

 

HT ITALIA SRL

• Site della Boaria, 40
• 48018 – Faenza (RA) – Italy
• T +39 0546 621002 | F +39 0546 621144
• M info@ht-instrumnets.com
• www.ht-instruments.it

OBE ANYỊ

Ajụjụ a na-ajụkarị

• Ajụjụ: Kedu ihe m ga-eme ma ọ bụrụ na ngwaọrụ ahụ gosipụtara ịdọ aka ná ntị batrị dị ala?
  A: Ọ bụrụ na batrị dị ala, tụlee iji dochie ya iji hụ na arụ ọrụ nke ọma nke ngwá ọrụ ahụ.
• Ajụjụ: Ngwa a nwere ike tụọ ma AC na DC voltagọ bụ?
  A: Ee, e mere ngwá ọrụ iji tụọ ma AC na DC voltages. Rụtụ aka na ihe ngosi LED na ngosipụta LCD maka ọgụgụ.

Akwụkwọ / akụrụngwa

Ngwa HT HT10 Ogwe abụọ Voltage onye nyocha [pdf] Akwụkwọ ntuziaka onye ọrụ HT10, HT10 Ogwe abụọ Voltage Tester, Pole Abụọ Voltage Tester, Voltage Tester, Tester

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ