FUNLAB FF01 Hall Effect Controller
gafereview
Firefly Pro Controller–Instruction Manual
Nkọwapụta ngwaahịa
| Otu | Nkọwapụta |
| Nlereanya | FF01 |
| Nnyefe Ọkara | Bluetooth 2.1 |
| Ugboro ụgbọelu | 2.402-2.480GHz |
| Protocol | Bluetooth BT2.1+EDR |
| Ikanam | 4 LEDs and Multiple Colored Lights |
| Batrị | Batrị Lithium Polymer 3.7V/950mAH |
| Oge nke ntachi obi | 12.5 Hours (Lights Turned Off) |
| Oge Nchaji | Awa 6.3 |
| Vol -arụ ọrụ Voltage | 3.7V-4.2V |
| Nchaji Voltage | 5V |
| Okpomọkụ na-arụ ọrụ | -10 Celsius C∼50 ° C |
| Okpomọkụ nchekwa | -20C-10C |
Ịgbanyụ ma ọ bụ gbanyụọ ọrụ njikwa (n'okpuru ọnọdụ mgbanwe)
Njikọ Ahịrị
Njikọ ikuku
- Site na NchNhr Ụlọ, họrọ Ndị njikwa, wee gbanwee njide na ịtụ.
- Press and hold Y + HOME for 3 seconds, and 4 LED lights flash quickly.
The LED(s) are becoming stable, pairing finishes. - If no pairing for over 2.5 minutes, it shuts down by itself.
- If paired and no operation for over 5 mins, shuts down by itself. (No movement on the sensor).
Ọrụ edemede: Press the Home Button, and then the console in the sleep state can be woken up and connected again.
Usoro ọrụ na ngosipụta LED (ntụziaka njikọ)
Mmakọ Mmakọ
- Combination Pairing: In the off state, press and hold the following key combination to enter the Pairing Mode.
- Android Mode: A+ HOME
LED2 - LED3 na-egbuke egbuke ngwa ngwa mgbe ị na-ejikọta, na LED2 - LED3 na-aga n'ihu mgbe ị na-ejikọta nke ọma; - Ụdị mgbanwe: Y + Ụlọ
LED1 – LED4 flash quickly while pairing, and the console automatically assigns when pairing is successful. - PC Mode: B + HOME
LED1 & LED4 flash quickly while pairing, and LEDl & LED4 keep on while pairing successfully; - iOS Mode: B+ HOME
LED1 & LED4 na-egbuke egbuke ngwa ngwa mgbe ị na-ejikọta, na LED1 & LED4 na-aga n'ihu mgbe ị na-ejikọta ya nke ọma (usoro nkwado: iOS 13.6 ma ọ bụ n'elu / iPadOS 13.6 ma ọ bụ n'elu); - Steam Deck Mode: Press the “STEAM” Button on the left side of the console – “Settings” -“Bluetooth” to connect
B+ Ụlọ - LED1 & LED4 na-enwu ngwa ngwa ka ị na-ejikọ ọnụ, yana LED1 & LED4 na-aga n'ihu ka ha na-ejikọ nke ọma.
Ọrụ Turbo na AUTO TURBO
N'ụdị ọ bụla
- Enwere ike ịtọ bọtịnụ na ọrụ TURBO: A/B/X/Y/L/R/ZL/ZR/D-pad button
- (For the 1st time) Press the TURBO Button+ one of the function buttons to achieve the Manual TURBO Function (Press and hold to launch continuously)
- (For the 2nd time) Press the TURBO Button+ one of the function buttons to achieve the Automatic TURBO Function (Automatically continuous launch)
- (For the 3rd time) Press the TURBO Button+ one of the function buttons to clear the TURBO Function (Clear)
- Mara: Press and hold the TURBO Button for 5 seconds (if the Vibration intensity is not 0%, there will be a vibration cue ) to clear all TURBO Functions.
Ndozi ọsọ TURBO (Ọkwa 3)
- Ụzọ mmezi:
- Press TURBO Button+ “Shake L/R Joystick Up”, increase speed by 1 level;
- Press TURBO Button+ “Shake L/R Joystick Down “, reduce speed by 1 level;
Ọkwa ọsọ:
- Na-aga n'ihu na-ebido ugboro 5 kwa nkeji (Ọkwa 1);
- Na-aga n'ihu na-ebido ugboro 12 kwa nkeji (Ọkwa 2);
- Na-aga n'ihu na-ebido ugboro 20 kwa nkeji (Ọkwa 3);
Ọrụ mmezi ịma jijiji
- Press the Motor Vibration Button on the back of the controller, and you can adjust the Motor Vibration Intensity. Vibration Intensity can be cycled in turn. There are 5 intensities, 100%, 75%, 50%, 25% and 0%.
Tọgharia ngwaike njikwa
- There is a small hole on the back of the controller, and it is the Reset Button. After pressing it, the controller hardware will reset.
Njikọta nke Onye njikwa
- When the controller is pairing to the previous device, you only need to press the HOME Button after the controller is in standby, and it will pair to the previous device.
Ngosipụta Nchaji
- Charging in the OFF State: LED4 flashes slowly, and then turns off while being fully charged;
- Nchaji ka ejikọrọ na Mgbanwe: Ọkụ (s) nke ọwa kwekọrọ ga-agbaji nwayọ nwayọ, wee na-aga n'ihu ka a na-akwụ ụgwọ zuru oke.
Lighting Control Instruction (Light Button
)
- Light up the luminous pattern: Press the
bọtịnụ. - Change the Light Color: Press, bọtịnụ.
Colors will change each time you press the bọtịnụ. - Change the Lighting Mode: Hold the,
Initial Mode: Always-on
1st time-click: breathing light mode
2nd time-click: quick flash mode
3rd time-click: vibration lighting mode
Back to Always-on: turn off and then turn on the light. - Turn OFF the light: Hold bọtịnụ maka 5 sekọnd.
Turn ON the light: Press bọtịnụ.
Ọrụ nnukwu na eserese na bọtịnụ azụ
Ọrụ Macro- bọtịnụ nnukwu
- Press and hold the MR Button and don’t loosen (4 LED lights turn on, entering programming), inputting the buttons you want to edit (up to 24 steps). The controller will have the vibration cue after loosening the MR Button and then pressing the XR Button to trigger the Macro Buttons.
- Press and hold the ML Button and don’t loosen (4 LED lights turn on, entering programming), inputting the buttons you want to edit (up to 24 steps). The controller will have the vibration cue after loosening the ML Button and then pressing the XL Button to trigger the Macro Buttons. Buttons that Macro Function could edit are A/B/X/Y/L/R/ZL/ZR/+/-/D-pad Buttons and L/Rjoysti cks (can be used as a combo in the game).
Ọrụ eserese - bọtịnụ mmemme
- Press and hold the MR Button and don’t loosen (4 LED lights turn on, entering programming), inputting the single button you want to map. The controller will have the vibration cue after loosening the MR Button and then pressing the XR Button to trigger the Programmable Buttons.
- Press and hold the MR Button and don’t loosen (4 LED lights turn on, entering programming), inputting the single button you want to map. The controller will have the vibration cue after loosening ML Button, and then pressing XL Button to trigger Programmable Buttons; and Buttons that Map ping Function could edit are A/B/X/Y/L/R/ZL/ZR/+/-/D-pad Buttons L/Rjoysti cks.
Mara:
- Na Ọrụ Nchekwa;
- Press the MR/ML Buttons that set programming, and there is a vibration cue, and then you can clear the Macro and Mapping Function of the XR/XL Buttons.
Keylinker APP Instructions
- Open the app store and search for “Keylinker” to download the APP.
- Open the Bluetooth connection handle.
- APP KEYLINKER BLE appears, click, and connect successfully.
- Click the settings icon on the right to enter the settings page.
- You can change the Button in the APP, set the lights, adjust the vibration, etc
Nkwado
- We promise to provide sustainable services for this controller. You can get more operational guidance support from our service channel and official web:
- Websaịtị: www.funlabswitch.com
- Instagebule: funlab_official
- Ọrụ: support@funlabswitch.com
- Esemokwu:
Akwụkwọ / akụrụngwa
 |
FUNLAB FF01 Hall Effect Controller [pdf] Akwụkwọ ntuziaka FF01, FF01 Hall Effect Controller, Hall Effect Controller, Effect Controller, Controller |