Ngwa ELECROW ESP32 Development Board
Ịdọ aka ná ntị nchekwa dị mkpa
- Enwere ike iji ngwa a ụmụaka sitere na afọ 8 na karịa yana ndị nwere ike anụ ahụ, mmetụta uche ma ọ bụ nke uche ma ọ bụ enweghị ahụmahụ na ihe ọmụma ma ọ bụrụ na enyerela ha nlekọta ma ọ bụ ntụziaka gbasara iji ngwa ahụ n'ụzọ dị nchebe ma ghọta ihe egwu dị na ya. .
- Ụmụaka agaghị eji ngwa eji egwu egwu.
- Ụmụaka agaghị eme nhicha na nlekọta onye ọrụ na-enweghị nlekọta.
- Ịdọ aka ná ntị: Jiri nkeji ọkọnọ nwere ike ịpụpụ a na-enye naanị ngwa a.
Nkọwapụta
| Isi Chip | Nhazi usoro | Xtensa® 32-bit LX7 |
| Ebe nchekwa | 16MB Flash 8MB PSRAM | |
| Ọsọ kacha | 240Mhz | |
|
Wi-Fi |
802.11 a/b/g/n 1 × 1,2.4 GHz band na-akwado 20 na 40 MHz bandwit, na-akwado ọdụ, SoftAP, na SoftAP + Station agwakọta ụdịdị. | |
| Bluetooth | BLE 5.0 | |
| Ihuenyo LCD | Mkpebi | 320*480 |
| Ngosipụta nha | 3.5 inch | |
| Ụgbọ ala IC | IL9488 | |
| Metụ aka | Mtụ aka Capacitive | |
| Interface | Njikọ SPI | |
| Modul Dther | Igwefoto OV2640, 2M Pixel | |
| Igwe okwu MEMS | ||
| Kaadị SD n'elu kaadị SD kaadị | ||
| Interface | 1 x USB C 1 x UART 1 x I2C 2x Analog 2x Digital | |
| Bọtịnụ | Tinyegharịa bọtịnụ Pịa bọtịnụ a ka ịtọgharịa sistemụ. | |
| Jide bọtịnụ buut wee pịa bọtịnụ nrụpụta BOOT ka ịmalite ọnọdụ nbudata firmware. Ndị ọrụ
nwere ike budata firmware site na ọdụ ụgbọ mmiri. |
||
| Na-arụ ọrụ
gburugburu |
Nrụ ọrụ Voltage USB DC5V, batrị lithium 3.7V
Nkezi nke na-arụ ọrụ ugbu a 83mA |
|
| Okpomọkụ na-arụ ọrụ -10 ~ 65 Celsius C | ||
| Mpaghara nọ n'ọrụ | 73.63(L)*49.79mm(W) | |
| Nha nha | 106(L) x66mm(W)*13mm(H) | |
Ndepụta akụkụ
- 1 x 3.5 inch SPI Ngosipụta nwere igwefoto (gụnyere acrylic Shell)
- 1 x eriri USB C
Akụrụngwa na Interface
Ngwaike karịrịview 
- bọtịnụ Tọgharia.
Pịa bọtịnụ a ka ịtọgharịa sistemụ. - ọdụ ụgbọ mmiri LiPo.
Igwe nchaji batrị lithium (batrị lithium agụnyeghị) - Bọtịnụ BOOT.
Jide bọtịnụ buut wee pịa bọtịnụ RESET ka ịmalite ọnọdụ nbudata firmware. Ndị ọrụ nwere ike budata firmware site na ọdụ ụgbọ mmiri - SV ike/ụdị C interface.
Ọ na-eje ozi dị ka ike ọkọnọ maka mmepe osisi na nkwurịta okwu interface n'etiti PC na ESP-WROOM-32. - 6 Crowtail interfaces (2 * Analog, 2 * Digital, 1 * UART, 1 * IIC).
Ndị ọrụ nwere ike hazie ESP32-S3 iji kparịta ụka na mpụta ejikọrọ na interface Crowtail.
Eserese atụmatụ nke Port 10
| GND |
ESP32 S3 |
GND | ||
| 3V3 | 101 | SCL | ||
| Tụgharịa | EN\RST | 102 | SDA | |
| vs | 104 | TXDO | UARTO_TX | |
| HS | 105 | RXDO | UARTO_RX | |
| D9 | 106 | 1042 | SPI_D/I | |
| MCLK | 107 | 1041 | MIC_SD | |
| D8 | 1015 | 1040 | D2 GPIO | |
| D7 | 1016 | 1039 | MIC_CLK | |
| PCLK
D6 |
1017
1018 |
1038
NC |
MIC_WS | |
| D2 | 108 | NC | ||
| 1019 | NC | |||
| 1020 | 100 | TP_INT/DOWNL | ||
| cs | 103 | 1045 | ||
| Azụ | 1046 | 1048 | D4 | |
| 109 | 1047 | D3 | ||
| cs | 1010 | 1021 | D5 | |
| D1 GPIO | 1011 | 1014 | SPI_MISO | |
| SPI_SCL | 1012 | 1013 | SPI_MOSI |
Ihe Mgbasawanye
- Eserese atụmatụ
- Koodu isi mmalite
- ESP32 usoro mpempe akwụkwọ
- Ụlọ akwụkwọ Arduino
- Ihe nkuzi 16 maka LVGL
- Ntuziaka LVGL
Mwepu
Ozi gbasara mkpofu maka ngwa eletriki na ngwa eletrọnịkị (WEEE). Akara a na ngwaahịa na akwụkwọ so ya pụtara na ngwaahịa eletrọnịkị na eletrọnịkị eji eme ihe ekwesịghị ịgwakọta ya na mkpofu ụlọ. Maka mkpofu kwesịrị ekwesị maka ọgwụgwọ, mgbake na imegharị ihe, biko buru ngwaahịa ndị a gaa na ebe nchịkọta ahapụtara ebe a ga-anabata ha n'efu. Na mba ụfọdụ ị nwere ike iweghachi ngwaahịa gị n'aka onye na-ere ahịa mpaghara gị mgbe ịzụrụ ngwaahịa ọhụrụ. Ịtụfu ngwaahịa a n'ụzọ ziri ezi ga-enyere gị aka ịchekwa akụ bara uru ma gbochie mmetụta ọ bụla nwere ike ime na ahụike mmadụ na gburugburu ebe obibi, nke nwere ike ịmalite site na mkpofu na-ekwesịghị ekwesị. Biko kpọtụrụ ndị isi obodo gị maka nkọwa ndị ọzọ gbasara ebe nchekwa WEEE dị nso
Maka nkọwa ndị ọzọ biko lelee koodu QR.
Kpọtụrụ Nkwado nka na ụzụ
E-mail: techsupport@elecrow.com
Akwụkwọ / akụrụngwa
 |
Ngwa ELECROW ESP32 Development Board [pdf] Ntuziaka onye ọrụ Ngwa ESP32 Development Board, ESP32, Kit Board Development, Kit Board |
