Akwụkwọ ntuziaka ntuziaka ebe nchekwa akpa C20

Nkọwapụta

• Ogologo: 6m
• Ogologo: 12m
• Ogologo: 2m

Mgbidi ngwụcha emechiri emechi maka C20 na-enweghị etiti

Mba.	Nkọwa	QTY
16A	Tension Tube for back panel	4
17	Angle Seat	6
18	Big ratchet	2
19	Efere ígwè	2
20	Bolt	6
21	Ụdọ	1
22	Mkpuchi	1

Chọpụta akụkụ ahụ mapụtara, wee lelee qty wee rụọ ọrụ dịka ndepụta dị n'elu.
Kpọkọta ihe mkpuchi ahụ dịka eserese dị n'elu.

Nzukọ

Model #C2040 W6x L12x H 2m Container Shelter

C2040 12x6x2m Ndepụta akụkụ
Koodu akụkụ	Nkọwa	Qty
L1	Base Plate at Left	9
R1	Base Plate at right	9
1	Ụzọ atọ dabara adaba	2
2	Ụzọ anọ dabara adaba	7
3	tube gbatịrị elu	18
4	Sidewall agbagọ tube	18
5	Ụlọ elu purlin	8
6	Njikọ purlin	32
7	Lower tensioning tube maka mkpuchi ụlọ	Otu narị ise
8	Oche akụkụ	4
9	Ihe mkpuchi ụlọ	1
10	Plastic nkwụnye	4
11	Ụdọ	1 iri na abuo
13	Kpọchie M8x70	144
14	Bolt nru ububa	16
14A	Rachet Straps	18
14B	1.5” Rachet (With Screw)	18

IMPORTANT READ MANUAL FIRST
Nkwadebe saịtị na-ezighi ezi, Mgbakọ na mmezi nwere ike imebi akwụkwọ ikike wee bute mmejọ na-enweghị isi na ọnụ ahịa. Ọ bụrụ na ị nwere ajụjụ ọ bụla kpọtụrụ onye na-ere ahịa mpaghara gị.
Maka mgbakọ enyi na enyi onye ọrụ anyị achọpụtala akụrụngwa nke ọ bụla nwere koodu akụkụ dịka egosiri na listi akụkụ. Biko rụtụ aka na nọmba koodu akụkụ na eserese iji hụ na mgbakọ na-enweghị nsogbu.
Ọ dị mkpa imechi akwa ụlọ nke ọma iji zere “hammocks” n'elu ụlọ ma na-agbatịkwa otu ugboro ma ọ bụ ugboro abụọ ọzọ ka ejiri ọnwa ole na ole. Nke a dị mkpa mgbe mgbakọ na ihu igwe oyi (mgbụsị akwụkwọ na oyi) n'ihi na ákwà ahụ na-esi ike mgbe ahụ na mgbe anyị nwetara anyanwụ na ihu igwe na-ekpo ọkụ mgbe e mesịrị, ọ ga-eme ka ákwà ahụ "kwụsị" ọzọ ma ọ dị mkpa ka a na-agbanyeghachi tupu oyi ọzọ.
Ọ bụ ndị nwe ya ka ha were snoo ozugbo ma ọ bụrụ na ha ewepụghị ya n'onwe ya.

READALL INSTRUCTIONS BEFOREASSEMBLY

1. Keep work area clean. Cluttered areas invite injuries. Do not set up near snowdrifts, in slippery places, in high winds, or wet location.
2. Debe ụmụaka pụọ. Ekwesịrị idobe ụmụaka niile n'ebe ọrụ.
3. Emechala iru eru. Debe ụkwụ kwesịrị ekwesị na nguzozi mgbe niile.
4. Ejila mmanya na-egbu egbu ma ọ bụ ọgwụ ọjọọ na-agbakọta ọnụ. Gụọ akara ịdọ aka ná ntị na ndenye ọgwụ iji chọpụta ma mkpebi gị ma ọ bụ echiche gị adịghị mma mgbe ị na-aṅụ ọgwụ. Ọ bụrụ na enwere obi abụọ, ekpokọtala.
5. Mara maka ọnọdụ ikuku nwere ike; gbanye ntọala na kọmpụta ma ọ bụrụ na ọnọdụ ndị a nwere ike ime. Wepu mkpuchi n'oge ifufe.
6. Kpachara anya na ike na isi mmalite okpomọkụ. Ejila ebe okpomọkụ dị nso na tarpaulin. Ewepụla ya n'ọkụ mepere emepe.
7. Be aware of personal safety during assembly and use. Be carful not to pinch fingerswith clips and tubes when assembling: when using makes sure there is adequate ventilation for exhaust and other dangerous fumes.

Akụrụngwa na ngwaọrụ maka ntinye

1. Ihe teepu
2. Eriri maka nhazi
3. Ubube nzọụkwụ
4. Welder
5. sledge hamma
6. Wrench
7. Mmasị

Isi ntọala

Please refer to the diagram to place the base plates.

1. Ihe nha bụ site na etiti ruo etiti tubes. Na-ezo aka na eserese dị n'elu ma kwadoo ebe efere ntọala. Gbaa mbọ hụ na ntọala ndị ahụ bụ square.
2. Efere ala niile kwesịrị iji welder wee gbado ya na arịa.

Echichi osisi

1. As Figure 2 shown find Three-way fitting (part code 1), Top bent tube (part code 3) and Sidewall bent tubes (part code4). To connect them by Screw M8x70 （ part code13). Which makes one group of arch.
   • Biko rụba ama the direction of the screw. DO NOT install the screws on the top of the truss where the fabric will rest.
2. Lift an assembled arch into one base plate and force the other end of the arch into theopposite base plate.
   Mgbe ị na-emecha wụnye arches abụọ mbụ, jikọọ Njikọ purlin onto them by using screw M8x70（part code 13）.There is 4 pieces of Connection purlins (part code 6) and 1 piece of Top roof purlin (part code 5) between each arch. Then install the third arch into base plate and connect the purlins. By turns the assembly for the frame is finished.

Wụnye mkpuchi mkpuchi ụlọ

IHE: Awụnyela mkpuchi n'elu etiti nke ụlọ gị n'ọnọdụ ikuku dị elu. Obere ikuku bụ ihe kacha agba ọsọtageous maka mkpuchi echichi. Iji nweta advantage nke ikuku, dọpụta ihe mkpuchi n'elu arches na ikuku na-efe na mkpuchi dị ka ụgbọ mmiri jupụtara na ikuku.

1. Tinye mkpuchi mkpuchi ụlọ (koodu akụkụ 9) EKWU, CARRFULLR na nwayọ na etiti. Gbanwee mkpuchi ka ọ bụrụ square na nke dabara adaba na etiti ahụ.
2. Weld the Angle seats (part code 8) on each container and use Rope (part code 11)to knit the cover on the two side arches, finally tie the Roof cover to the Angle seats.
3. Cut pockets above Rachet (No.14B) according to the position of the base plates and put the Lower tensioning tubes for roof cover (part code 7) into the pocket of roof cover. Then use the Rachet Straps (part code14A) to tie down the Lower tensioning tubes like the Figure.
4. Finally install the∮ 32 Plastic plug for base rail section (part code 10) into two
   end of the Lower tensioning tubes.

IHE: DO NOT LEAVE THE ROOF COVER UNATTACHED UNDERANY CIRCUMSTANCES until the final assembly and tightening has been completed.
The process is quite easy. But some tightening adjustments will be necessary o to produce a flat, tensioned roof cover. Please adjust the roof cover every month.

Ajụjụ

What should I do if I find any missing or damaged spare parts?

If you encounter any missing or damaged parts, please contact our customer support for assistance. Provide details of the issue and we will help you resolve it promptly.

Can I purchase additional spare parts separately?

Yes, you can purchase additional spare parts separately. Contact our customer service team to inquire about ordering extra parts for your product.

Akwụkwọ / akụrụngwa

Ebe nchekwa akpa akpa C20 [pdf] Akwụkwọ ntuziaka W20ftContainerShelters, C20, C20 Ebe nchekwa nchekwa, C20, Ndobe akpa, ebe nchekwa

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ