Intermatic ETW2CP Wi-Fi Smart Timer Instruction Manual

1. Okwu mmalite

This manual provides detailed instructions for the installation, operation, and maintenance of the Intermatic ETW2CP Wi-Fi Smart Timer. The ETW2CP is a 2-circuit, 365-day programmable timer designed for automating lights, pumps, and industrial equipment. It features remote control via the Intermatic Connect app and is suitable for both indoor and outdoor applications.

2. Ozi nchekwa

Ịdọ aka ná ntị: Risk of electric shock. Installation and servicing must be performed by qualified personnel only. Disconnect power at the circuit breaker or fuse before installing or servicing. Follow all local and national electrical codes.

• Ensure power is disconnected before any wiring.
• Do not exceed the maximum load ratings of the device.
• This device is intended for permanent installation.
• Keep the enclosure door closed and latched when not in use to maintain its indoor/outdoor rating.

3. Ngwaahịa gafereview

The Intermatic ETW2CP is a sophisticated Wi-Fi enabled timer offering precise control over two independent circuits. Key features include:

• Nhazi ụbọchị 365: Supports up to 256 ON/OFF events and 64 holiday schedules.
• Nnweta dị anya: Control and monitor via the Intermatic Connect app.
• Dual SPDT Relays: Two independent Single-Pole Double-Throw outputs for versatile control.
• Indoor/Outdoor Enclosure: Durable plastic casing suitable for various environments.
• Akpaaka Voltage Nchọpụta: Compatible with 120-277 VAC input.
• LED-dakọtara: Designed to work with modern LED lighting systems.
• Nchedo Mfu Ike: Non-volatile memory retains programming during power outages.

Figure 1: Intermatic ETW2CP Wi-Fi Smart Timer with its cover open, showing the internal components and control panel. The left side of the enclosure displays product specifications and warnings, while the right side features control buttons, indicator LEDs, and terminal blocks for wiring connections.

Ọgụgụ 2: A zuru ezu view of the ETW2CP's control panel. Visible elements include the MODE button, SERVICE, MANUAL, and AUTO indicator LEDs, NETWORK status LED, RESET button, and two circuit control buttons (1 and 2). Below these are the terminal blocks for power input (L2/H, L1, NC, NO, COM) and two independent circuits (CIRCUIT 1, CIRCUIT 2).

4. Ntọala na nwụnye

4.1 Mounting the Timer

The ETW2CP timer is designed for surface mounting. Select a suitable location that allows for proper wiring and access. Ensure the mounting surface is stable and can support the weight of the timer.

1. Open the timer enclosure by unlatching the cover.
2. Use the provided mounting holes on the back of the enclosure as a template to mark drilling locations.
3. Drill appropriate pilot holes and secure the timer to the wall using suitable screws (not included).
4. Ensure the enclosure is level and securely fastened.

Foto 3: N'ihu view of the Intermatic ETW2CP Wi-Fi Smart Timer with its cover closed, displaying the Intermatic logo. This image shows the compact and sealed design of the enclosure.

4.2 Ntuziaka waya

Mkpa: All wiring must comply with national and local electrical codes. Disconnect power before proceeding.

1. Route power supply wires into the enclosure through appropriate knockouts.
2. Jikọọ ahịrị na-abata voltage (120-277 VAC) to the L1 and L2/H terminals.
3. Connect the neutral wire to the N terminal (if applicable for your wiring configuration).
4. Connect the load wires for Circuit 1 to the appropriate terminals (NO, NC, COM) for Circuit 1.
5. Connect the load wires for Circuit 2 to the appropriate terminals (NO, NC, COM) for Circuit 2.
6. Ensure all terminal screws are tightened securely.
7. Close and latch the enclosure cover.

Foto 4: Akụkụ view of the Intermatic ETW2CP timer, highlighting the conduit knockouts for electrical wiring entry. This view demonstrates the robust construction and provisions for secure cable management.

4.3 Njikọ Ike Mmalite na Wi-Fi

1. Restore power to the timer at the circuit breaker.
2. Download the "Intermatic Connect" app from your device's app store.
3. Follow the in-app instructions to create an account and add your ETW2CP timer to your network. The NETWORK LED on the timer will indicate connection status.

5. Ntuziaka ọrụ

5.1 Njikwa akwụkwọ ntuziaka

The ETW2CP allows for manual override of the scheduled programs.

• Pịa MODE button to cycle through operating modes: SERVICE, MANUAL, AUTO.
• In Akwụkwọ ntuziaka mode, press the circuit buttons (1 or 2) to toggle the connected load ON or OFF. The MANUAL LED will illuminate.
• In AUTO mode, the timer operates according to its programmed schedule. The AUTO LED will illuminate.

5.2 App-Based Scheduling

All advanced scheduling and programming are managed through the Intermatic Connect app.

1. Open the Intermatic Connect app on your smartphone or tablet.
2. Select your ETW2CP timer from the device list.
3. Navigate to the "Schedules" section to create, edit, or delete ON/OFF events and holiday schedules.
4. Use the app to set astronomical clock functions, daylight saving adjustments, and other advanced settings.
5. The app also provides real-time status updates and remote ON/OFF control for each circuit.

6. Nlekọta

The Intermatic ETW2CP Wi-Fi Smart Timer requires minimal maintenance.

• Nhicha: Periodically wipe the exterior of the enclosure with a damp akwa . Ejila ihe nchacha abrasive ma ọ bụ ihe mgbaze.
• Mmelite femụwe: Ensure the Intermatic Connect app is up-to-date, as it will notify you of any available firmware updates for your timer. Follow in-app instructions for updating.
• Nyocha: Annually inspect the wiring connections for tightness and signs of wear. Ensure the enclosure door seal is intact.

7. Nchọpụta nsogbu

If issues persist, contact Intermatic Customer Support.

8. Nkọwapụta

9. Akwụkwọ ikike na nkwado

For warranty information and technical support, please visit the official Intermatic websaịtị ma ọ bụ kpọtụrụ ngalaba ọrụ ndị ahịa ha. Debe nnata nzụta gị ka ihe akaebe nke ịzụrụ.

Intermatic Websaịtị: www.intermatic.com