Okwu mmalite
Thank you for choosing the CERWIN-VEGA! CVP12D4 12-inch Dual Voice Coil Car Audio Subwoofer. This manual provides essential information for the proper installation, operation, and maintenance of your subwoofer. Please read it thoroughly before proceeding with installation or use to ensure optimal performance and longevity of your product.
Ozi nchekwa
- Kwụpụ batrị ụgbọala ahụ mgbe niile tupu ị rụọ ọrụ eletriki ọ bụla.
- Hụ na waya niile dị n'ime mmiri nke ọma iji gbochie sekit dị mkpụmkpụ.
- Mount the subwoofer securely to prevent movement during vehicle operation.
- Avoid exposing the subwoofer to excessive moisture or extreme temperatures.
- Consult a professional car audio installer if you are unsure about any aspect of the installation process.
Kedu ihe dị na Igbe ahụ
- 1 x CERWIN-VEGA! CVP12D4 12-inch Dual Voice Coil Subwoofer
- Nwụnye kposara
Atụmatụ
- Parabolic One-Piece Stamped Carbon Fiber Poly Cone: Designed for rigidity and accurate bass reproduction.
- Single Stitched Rubber Surround: Provides durability and controlled cone excursion.
- Bumped Back Plate: Allows for maximum voice coil excursion without mechanical interference.
- Vented Motor Structure: Optimizes thermal heat dissipation, enhancing power handling and reliability.
- Poly-Cotton Spider with Spaced Woven-In Tinsel Wires: Ensures consistent performance and longevity of the voice coil leads.
Nkọwapụta
| Nkọwapụta | Uru |
|---|---|
| Aha Nlereanya | Usoro CVP |
| Ụdị Ọkà Okwu | Subwoofer |
| Eji akwadoro maka ngwaahịa | Maka Ụgbọ ala |
| Ngwa dakọtara | Audiogbọ ala Audio |
| Mgbochi | 4 Ohms (Dual Voice Coil) |
| Akụkụ ngwaahịa | 5.8"D x 12"W x 5.8"H |
| Nha Ọkà Okwu | 12 sentimita asatọ |
| Ike Nwepu kacha elu | 550 Watt |
| Nzaghachi ugboro ugboro | 150 Hz (Oke Elu) |
| Teknụzụ Njikọta | RCA (for ampntinye liifier) |
| Ọnọdụ mmepụta ọdịyo | Mono |
Ntọala & Nwụnye
Proper installation is crucial for the performance and safety of your subwoofer. If you are not experienced with car audio installations, it is highly recommended to seek professional assistance.
Ịkwanye
The CVP12D4 subwoofer is designed for door mount applications, typically within a sealed or ported enclosure. Ensure the enclosure is robust and properly sized for the subwoofer's specifications. Use the provided installation screws to secure the subwoofer firmly to the enclosure. Verify that there is adequate clearance behind the subwoofer for proper excursion and ventilation.
Wiring Dual Voice Coil Subwoofers
The CVP12D4 features a Dual Voice Coil (DVC) design, offering flexibility in wiring configurations to match your amplifier's impedance requirements. Each voice coil has a 4 Ohm impedance.
- Series Wiring (8 Ohms Total): Connect the positive terminal of Voice Coil 1 to the negative terminal of Voice Coil 2. Then, connect the amplifier's positive output to the positive terminal of Voice Coil 2, and the amplifier's negative output to the negative terminal of Voice Coil 1. This configuration results in an 8 Ohm load.
- Parallel Wiring (2 Ohms Total): Connect the positive terminals of Voice Coil 1 and Voice Coil 2 together. Connect the negative terminals of Voice Coil 1 and Voice Coil 2 together. Then, connect the amplifier's positive output to the combined positive terminals, and the amplifier's negative output to the combined negative terminals. This configuration results in a 2 Ohm load.
Hụkwa gị mgbe niile amplifier is stable at the chosen impedance. Incorrect wiring can damage both the subwoofer and the ampna -emegharị ihe.
Foto: N'ihu view of the CERWIN-VEGA! CVP12D4 12-inch Dual Voice Coil Subwoofer, showcasing its black parabolic carbon fiber poly cone and rubber surround.
Ntuziaka ọrụ
Once installed, follow these general guidelines for operating your subwoofer:
- Ike izizi: Malite na nke gị amplifier's gain settings at their lowest. Gradually increase the volume and gain to avoid overdriving the subwoofer.
- Ntọala crossover: Jiri nke gị amplifier's low-pass filter (LPF) to send only low frequencies to the subwoofer. A common starting point is 80-100 Hz.
- Subsonic Myọcha: Ọ bụrụ na gị amplifier has a subsonic filter, enable it and set it slightly below your enclosure's tuning frequency to protect the subwoofer from damaging ultra-low frequencies.
- Oge nkwụsị: Allow a break-in period of several hours of moderate listening before pushing the subwoofer to its limits. This allows the suspension components to loosen up.
Nlekọta
- Nhicha: Use a soft, dry cloth to clean the subwoofer cone and surround. Avoid harsh chemicals or excessive moisture.
- Nyocha: Periodically inspect the subwoofer for any signs of damage to the cone, surround, or wiring connections.
- Nkwanye echekwabara: Ensure the subwoofer remains securely mounted in its enclosure.
Nchọpụta nsogbu
- Enweghị ụda: Check all wiring connections (power, ground, remote, RCA, speaker wires) for proper contact and polarity. Verify amplifier is powered on and not in protect mode.
- Ụda agbagọ: Belata amplifier gain or head unit volume. Check for proper crossover settings. Ensure the subwoofer is not overdriven.
- Bass adịghị ike: Nyochaa amplifier gain is set correctly. Check subwoofer wiring for correct impedance match. Ensure enclosure is sealed (if applicable) and properly sized.
- ekpo oke ọkụ: Gbaa mbọ hụ na ikuku ikuku zuru oke maka amplifier. Check impedance match between subwoofer and amplifier. Reduce listening levels if the subwoofer or amplifier becomes excessively hot.
Akwụkwọ ikike & Nkwado
This CERWIN-VEGA! CVP12D4 subwoofer comes with a limited warranty. Please refer to the warranty card included with your product for specific terms, conditions, and duration. For technical support, service, or warranty claims, please contact Cerwin Vega customer service through their official website or authorized dealers. Keep your proof of purchase for warranty validation.
