Globo Lighting BOSTON Outdoor Pedestal Light

1. Okwu mmalite

Thank you for choosing the Globo Lighting BOSTON Outdoor Pedestal Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions carefully before installation and retain them for future reference.

Image 1.1: The BOSTON outdoor pedestal light providing illumination along a pathway.

2. Ntuziaka nchekwa

• Nchekwa Eletriki: Onye ọrụ ọkụ eletrik ruru eru ga-arụ ọrụ nrụnye ahụ dịka iwu niile nke mpaghara na mba si dị. Wepụ ike mgbe niile na ihe mgbawa sekit isi tupu etinye ya, rụzie ya, ma ọ bụ dochie bọlbụ.
• Ojiji n'èzí: This fixture is designed for outdoor use. Ensure all connections are waterproof and sealed appropriately to prevent water ingress.
• Ụdị bọlbụ: Use only E27 bulbs with the specified wattage. Agafela oke wattage gosiri na nkwụnye.
• Ijikwa: Handle the fixture with care. Avoid dropping or subjecting it to strong impacts.
• Nhicha: Do not use abrasive cleaners or solvents. Clean with a soft, damp akwa .
• Okpomọkụ: Hapụ bọlbụ ahụ ka ọ jụọ oyi kpamkpam tupu ị nwaa ịgbanwe ya.

3. Ihe ngwugwu

Please check that all components are present and undamaged before beginning installation:

• 1x BOSTON Outdoor Pedestal Light Fixture (Model 105701)
• 1x Nkwalite ntọala
• 1x Set of Mounting Hardware (screws, anchors)
• 1x Akwụkwọ ntuziaka onye ọrụ

Note: E27 bulb is not typically included and must be purchased separately.

4. Nkọwapụta

5. Ntọala na nwụnye

Ihe dị mkpa: Ensure the main power supply is switched off at the circuit breaker before commencing installation.

1. Họrọ ebe: Select a suitable outdoor location for the pedestal light, ensuring it is on a stable, level surface and has access to the necessary electrical wiring.
2. Kwadebe waya: If not already present, run appropriate outdoor-rated electrical cable to the installation point. Consult a qualified electrician for this step.
3. Ugwu Base: Position the mounting base on the desired surface. Mark the drilling points through the holes in the base. Drill pilot holes and secure the base using the provided mounting hardware (screws and anchors). Ensure the base is firmly attached.
4. Jikọọ waya eletrik: Carefully connect the electrical wires from your power supply to the terminals inside the fixture. Follow the standard wiring color codes (e.g., Live, Neutral, Earth). Ensure all connections are secure and properly insulated.
5. Wụnye bọlbụ: Insert a suitable E27 bulb (not included) into the lamp njide. Akwụsịla elu.
6. Ndozi echedoro: Attach the main body of the pedestal light to the mounted base, ensuring it is securely fastened and sealed against moisture.
7. Weghachi ike: Ozugbo e mechara nrụnye ahụ ma njikọ niile dị nchebe, weghachite ike na isi ihe mgbawa sekit ahụ.

Image 5.1: The pedestal light installed on a patio, demonstrating a typical mounting scenario.

6. Ntuziaka ọrụ

The BOSTON Pedestal Light features an integrated motion sensor for automatic operation.

• Ike Na: Once installed and power is restored, the light will enter a warm-up period (typically a few seconds) before the motion sensor becomes active.
• Sensọ ngagharị: The integrated motion sensor detects movement within its detection range. When motion is detected, the light will illuminate.
• Nwepu akpaaka: After a period of no detected motion, the light will automatically turn off. The duration of illumination is typically pre-set or adjustable via controls on the sensor (if available). Refer to the sensor's specific markings for adjustment options.
• Ihe mmetụta ụbọchị/abalị: The motion sensor also includes a photocell that prevents the light from activating during daylight hours, conserving energy. The light will only activate due to motion when ambient light levels are low enough.

Image 6.1: Detail of the motion sensor on the pedestal light, highlighting its detection area.

Image 6.2: The pedestal light operating at night, with the motion sensor detecting movement.

7. Nlekọta

• Nhicha: Jiri nwayọ na-ehicha ihe ndozi mgbe niile, damp cloth to remove dirt and debris. Do not use harsh chemicals or abrasive materials, as these can damage the finish or plastic components.
• Ndokwa bọlbụ:
  1. Ensure the power supply to the fixture is turned off at the circuit breaker.
  2. Hapụ bọlbụ ochie ahụ ka ọ jụọ oyi kpamkpam tupu ị metụ ya aka.
  3. Carefully unscrew the top cover or access panel to reach the E27 bulb.
  4. Unscrew the old bulb and replace it with a new E27 bulb of the correct wattage.
  5. Securely reattach the cover or access panel, ensuring a watertight seal.
  6. Weghachi ike.
• Nyocha: Periodically inspect the fixture for any signs of wear, damage, or loose connections. Address any issues promptly to ensure continued safe operation.

8. Nchọpụta nsogbu

If you experience persistent issues not covered here, please contact a qualified electrician or the product supplier.

9. Akwụkwọ ikike na nkwado

This product is covered by the standard warranty provided by the manufacturer. Please retain your proof of purchase for any warranty claims. For technical support or further assistance, please contact your retailer or the Globo Lighting customer service department.

A na-ahụkarị ozi kọntaktị na ngwugwu ngwaahịa ma ọ bụ na gọọmentị nke onye nrụpụta. websaịtị.