TechniSat DIGICLOCK 3 FM Projection Radio Alarm Clock User Manual

Okwu mmalite

The TechniSat DIGICLOCK 3 is an FM projection radio alarm clock designed to display time clearly on its LED screen and project it onto a wall or ceiling. This manual provides detailed instructions for its setup, operation, and maintenance to ensure optimal performance.

Foto: N'ihu view of the TechniSat DIGICLOCK 3, showing the digital time display and the time projected from the top.

1. Nhazi

1.1 Njikọ ike

Connect the integrated power adapter to a standard electrical outlet. For backup power during outages, insert optional batteries (not included) into the battery compartment. This ensures time and alarm settings are retained.

1.2 Njikọ antenna

Extend the integrated FM wire antenna for optimal radio reception. Position the antenna away from other electronic devices to minimize interference.

1.3 Ntọala Oge Mmalite

Upon first power-up or after a complete power loss without battery backup, the time may need to be set manually. Refer to the "Setting Time and Date" section under Operating Instructions for details.

2. Ntuziaka ọrụ

2.1 Na-achịkwaview

Foto: Top view of the alarm clock, highlighting the various control buttons for time, alarm, radio, and projection functions.

The top panel of the DIGICLOCK 3 features several buttons for controlling its functions:

• TIME SET / PRESET: Used to set the time and save/recall radio presets.
• Mkpu: Activates/deactivates alarms.
• PROJECTION ON/OFF / 180° FLIP: Controls the projection feature and flips the projected image.
• Ụra / ura: Activates snooze during an alarm or sets the sleep timer for radio playback.
• AL VOL+ / AL VOL-: Adjusts alarm volume.
• MIN/TUNE+ / HOUR/TUNE-: Adjusts minutes/hours and tunes radio frequencies.

2.2 Ịtọ oge na ụbọchị

1. Pịa ma jide Oge setịpụrụ button. The hour display will flash.
2. Jiri ihe HOUR/TUNE- na MIN/TUNE+ bọtịnụ iji dozie elekere.
3. Pịa Oge setịpụrụ again. The minute display will flash.
4. Jiri ihe HOUR/TUNE- na MIN/TUNE+ bọtịnụ iji dozie nkeji.
5. Pịa Oge setịpụrụ to confirm and exit time setting mode.

2.3 Ọrụ mkpu

The DIGICLOCK 3 supports two independent alarms (Alarm 1 and Alarm 2).

Ịtọ ntọala mkpu:

1. Pịa ma jide Mkpu button. "AL1" or "AL2" will flash.
2. Pịa Mkpu repeatedly to select Alarm 1 or Alarm 2.
3. Jiri HOUR/TUNE- na MIN/TUNE+ ka ịtọ oge oti mkpu chọrọ.
4. Pịa Mkpu iji kwado oge.
5. Select the alarm source (FM radio or buzzer) using HOUR/TUNE- na MIN/TUNE+.
6. Pịa Mkpu to confirm and activate the alarm. An alarm icon will appear on the display.

Ọrụ Sooze:

Mgbe oti mkpu na-ada, pịa URUA bọtịnụ ka mechie ya nwa oge. Oti mkpu ga-ada ọzọ ka ihe dị ka nkeji 9 gachara.

Stopping an Alarm:

To stop an alarm completely, press the Mkpu button. The alarm will reset for the next day. To deactivate an alarm, press the Mkpu bọtịnụ ruo mgbe akara ngosi mkpu ahụ ga-apụ n'anya na ngosipụta ahụ.

2.4 FM Redio arụ ọrụ

Tuning Radio Stations:

Pịa Mgbanyụ/ Gbanyụọ redio button to turn on the FM radio. Use the HOUR/TUNE- na MIN/TUNE+ buttons to manually tune to a desired frequency. Press and hold these buttons for automatic scanning.

Storing and Recalling Presets:

The device can store up to 10 FM radio stations.

1. Tinyegharịa n'ọdụ ụgbọ mmiri achọrọ.
2. Pịa ma jide PRESET button until a preset number flashes.
3. Jiri HOUR/TUNE- na MIN/TUNE+ to select a preset number (P01-P10).
4. Pịa PRESET ọzọ iji chekwaa ọdụ ụgbọ mmiri.
5. To recall a preset, briefly press the PRESET bọtịnụ wee jiri HOUR/TUNE- na MIN/TUNE+ iji họrọ ihe achọrọ.

Oge ụra:

Mgbe redio na-akpọ, pịa Ụra button repeatedly to set a sleep timer (e.g., 90, 60, 30, 15 minutes). The radio will automatically turn off after the set time.

2.5 Time Projection

Foto: Akụkụ view of the alarm clock, focusing on the projector lens which can be rotated to adjust the projection angle.

The DIGICLOCK 3 features an integrated projector to display the time on a wall or ceiling.

• Activating/Deactivating Projection: Pịa MKWUO/ Gbanyụọ oru ngo bọtịnụ iji gbanye ma ọ bụ gbanyụọ ihe ngosi ahụ.
• Na-edozi akụkụ amụma: Rotate the projector lens on top of the unit to adjust the angle of the projected time up to 180 degrees.
• Flipping Projected Image: If the projected time appears upside down, press the Mgbanwe 180° button (often combined with PROJECTION ON/OFF) to rotate the image 180 degrees.
• Ndozi anya: A small ring around the projector lens can be rotated to adjust the focus of the projected image for clarity.

Note: The clarity and visibility of the projected time may vary depending on ambient light conditions and projection distance. Optimal projection distance is typically within 1 to 1.5 meters.

2.6 Ngosipụta ihie

The 1.2-inch LED display offers two brightness levels. Briefly press the URUA button (when no alarm is active) to cycle between the brighter and dimmer display settings.

3. Nlekọta

3.1 Nhicha

Wipe the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the surface. Ensure no liquids enter the device.

3.2 nnọchi batrị

If using optional backup batteries, replace them periodically (e.g., annually) or when the display shows signs of power loss during an outage. Use the specified battery type and dispose of old batteries responsibly.

4. Nchọpụta nsogbu

5. Nkọwapụta

6. Akwụkwọ ikike na nkwado

Spare parts availability for this product is indicated for 1 year from the date of purchase. For further support or warranty inquiries, please refer to the contact information provided with your purchase documentation or visit the official TechniSat websaịtị.