Okwu mmalite
This manual provides detailed instructions for the installation, operation, and maintenance of your aigo AF12 3-in-1 ARGB Fan Kit. Please read this manual thoroughly before use to ensure proper functionality and longevity of the product.
Njirimara ngwaahịa
The aigo AF12 3-in-1 ARGB Fan Kit offers efficient cooling and customizable lighting for your computer system. Key features include:
- Ụdị: AF123IN1-BK
- Ọnụọgụ Fans: 3 x 120mm fans
- Ọsọ onye ofufe: 800-2000 RPM (±10%)
- Fan Noise Level: ≤30dBA
- Ofufe ikuku: 86.6 CFM
- Nrụgide static: 1.27mm-H²O
- Working Current (Motor): ≤0.2A (12V)
- Working Current (Light): ≤0.48A (5V)
- Akụkụ: 120 x 120 x 25 mm
- Ọkụ ARGB: Addressable RGB lighting for customizable effects.
Ihe ngwugwu
Chọpụta na ihe niile edepụtara n'okpuru dị na ngwugwu gị:
- 3 x aigo AF12 ARGB Fans
- Ịkwanye kposara
- ARGB Controller (if included in kit)
- Cables (Power, ARGB Sync)
Ntuziaka nwụnye
Follow these steps to properly install your aigo AF12 ARGB fans into your computer case.
- Kwadebe Sistemu gị: Power off your computer and disconnect it from the power source. Open your computer case.
- Chọpụta ebe ndị a na-etinye ihe ndị a: Determine the desired locations for your fans (e.g., front, top, rear, bottom of the case). Ensure proper airflow direction.
- Wụnye ndị Fans: Position each fan in its chosen location. Use the provided mounting screws to secure the fans to the case. Ensure the fan blades are not obstructed.
Image: An aigo AF12 fan viewed from an angle, highlighting the mounting points on its corners. This illustrates how the fan is secured.
- Jikọọ eriri ọkụ: Connect the 3-pin power connector from each fan to an available fan header on your motherboard or fan controller.
- Connect ARGB Cables: Connect the ARGB cable from each fan to the ARGB controller (if applicable) or directly to a compatible 5V 3-pin ARGB header on your motherboard. Ensure correct pin orientation to avoid damage.
Foto: A side profile of the aigo AF12 fan, illustrating the thickness and potential locations for cable connections on the frame.
- Njikwa USB: Route cables neatly to prevent interference with other components and to improve airflow.
- Mechie igbe na ike na: Close your computer case, reconnect the power, and power on your system.
Ntuziaka ọrụ
Once installed, your aigo AF12 ARGB fans will operate automatically based on your system's fan control settings. The ARGB lighting can be controlled via your motherboard's software or a dedicated ARGB controller.
Njikwa ọsọ ndị fan
Fan speed can typically be adjusted through your motherboard's BIOS/UEFI settings or through fan control software provided by your motherboard manufacturer. Refer to your motherboard manual for specific instructions.
Njikwa ọkụ ARGB
If connected to a 5V 3-pin ARGB header on your motherboard, use your motherboard's ARGB synchronization software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync) to customize lighting effects, colors, and patterns.
If using a dedicated ARGB controller (often included with fan kits), refer to the controller's specific instructions for lighting adjustments.
Nlekọta
Ndozi mgbe niile na-eme ka arụmọrụ kachasị mma ma na-agbatị ndụ nke ndị fan gị.
- Nhicha uzuzu: Periodically clean dust from the fan blades and housing using compressed air or a soft brush. Ensure the system is powered off before cleaning.
- Nyocha USB: Verify that all cables are securely connected and free from damage.
- Noise Monitoring: Listen for unusual noises, which may indicate a fan bearing issue or obstruction.
Nchọpụta nsogbu
If you encounter issues with your aigo AF12 ARGB fans, refer to the following common solutions:
Fans anaghị agba ọsọ
- Lelee Njikọ Ike: Ensure the fan's 3-pin power connector is securely plugged into the motherboard or controller.
- Check BIOS Settings: Verify that fan headers are enabled in your motherboard's BIOS/UEFI settings.
- Test Another Header: Try connecting the fan to a different fan header to rule out a faulty header.
ARGB Lights Not Working
- Check ARGB Connection: Ensure the 5V 3-pin ARGB connector is correctly and securely plugged into the motherboard or controller. Verify the pin orientation.
- Lelee ngwanrọ: Confirm that your motherboard's ARGB software is installed and configured correctly.
- ndakọrịta: Ensure your motherboard has a compatible 5V 3-pin ARGB header. This product is not compatible with 12V 4-pin RGB headers.
Oke mkpọtụ
- Lelee maka ihe mgbochi: Ensure no cables or other components are touching the fan blades.
- Arịọnụ kposara: Verify that all mounting screws are tightened to prevent vibrations.
- Nwulite uzuzu: Clean any dust from the fan blades.
Nkọwa nka nka
| Njirimara | Nkọwapụta |
|---|---|
| Ụdị | aigo |
| Nlereanya | AF123IN1-BK |
| Ọnụ ọgụgụ ndị fan | 3 x 120mm |
| Ọsọ fan | 800 ± 2000 ± 10% RPM |
| Igwe mkpọtụ fan | ≤30dBA |
| Ofufe ikuku | 86.6 CFM |
| Nrụgide Static | 1.27mm-H²O |
| Working Current (Motor) | ≤ 0.2A (12V) |
| Working Current (Light) | ≤ 0.48A (5V) |
| Akụkụ | 120 x 120 x 25 mm |
| Ike njikọ .dị | 3-Pin |
| Voltage | 12 volts |
| Usoro jụrụ oyi | Ikuku |
| Ngwa dakọtara | Desktọpụ |
| Ibu Ibu | 10.6 ounces |
Akwụkwọ ikike na nkwado
This aigo product comes with a Akwụkwọ ikike nke ọnwa 12 site na ụbọchị ịzụrụ, na-ekpuchi ntụpọ nrụpụta.
For technical support, warranty claims, or further assistance, please visit the official aigo store or contact their customer service through the details provided on their websaịtị.
Official aigo Store: aigo Store on Amazon
