Ntuziaka Ntuziaka maka ihe mmetụta mmegharị ASD LED n'èzí nke ìhè idei mmiri (Model A-SFL-20BK)

Okwu mmalite

This manual provides detailed instructions for the installation, operation, and maintenance of your ASD LED Motion Sensor Outdoor Flood Light, Model A-SFL-20BK. This advanced outdoor lighting solution features a 180° motion sensor, multiple lighting modes, adjustable color temperature, and rotatable light heads for optimal illumination and security.

ASD LED Motion Sensor Outdoor Flood Light with packaging

Foto: The ASD LED Motion Sensor Outdoor Flood Light, Model A-SFL-20BK, shown with its packaging. This image illustrates the product's design and included components.

Ozi nchekwa

Please read and understand all instructions before beginning installation. Failure to follow these instructions may result in electric shock, fire, or other hazards that could cause property damage or personal injury. Keep this manual for future reference.

Nchekwa Eletriki: Always turn off power at the circuit breaker before installing or servicing the fixture. Ensure all wiring connections are secure and comply with local electrical codes.
Nda ala: The fixture must be properly grounded to prevent potential electrical shock.
Eletrik tozuru oke: Ọ bụrụ na obi adịghị gị mma maka akụkụ ọ bụla nke usoro nrụnye ahụ, gakwuru ọkachamara ọkụ eletrik ruru eru.
Okpomọkụ arụ ọrụ: Do not operate the fixture outside its specified temperature range.
Ebe mmiri mmiri: This fixture is rated IP65 for wet locations, but ensure all seals and connections are properly secured during installation to maintain this rating.

Ntọala na nwụnye

Follow these steps for proper installation of your flood light. Ensure power is OFF at the circuit breaker before proceeding.

1. Kwadebe maka nwụnye

Wepụ ihe e ji arụ ọrụ ahụ ma lelee ma ọ bụrụ na ọ mebiri emebi.
Ensure all necessary mounting hardware is present.
Gbanyụọ ọkụ na isi sekit.

2. Ịkwanye ihe ndozi

Jikọọ ihe nkwado na-arị elu na igbe nkwụsị na-eji skru enyere.
Feed the electrical wires from the junction box through the gasket and into the fixture's wiring compartment.
Chekwaa ihe nrụnye ahụ na nkwado nkwado.

3. Njikọ njikọ

Jikọọ nwa waya site na nkwụnye ahụ ruo na black (live) wire from the power supply.
Jikọọ ọcha waya site na nkwụnye ahụ ruo na white (neutral) wire from the power supply.
Jikọọ green (ground) waya site na nkwụnye ahụ ruo na green or bare copper (ground) wire from the power supply.
Ensure all connections are secured with wire nuts and tucked neatly into the junction box.

4. Ịgbanwe Isi Ọkụ

The light heads are rotatable 150° side-to-side and 180° up-and-down. Adjust them to cover your desired illumination area.

Rotatable light heads for directional control

Foto: Illustration showing the 180° up-and-down and 150° side-to-side rotation capabilities of the flood light heads, allowing for precise light direction.

Foto: Detailed product specification diagram showing dimensions (10-1/4" L x 4-7/16" W x 6-13/16" H) and key features like motion sensor, photocell, 20W power, 5CCT, 2045lm brightness, and IP65 wet location rating.

Ntuziaka ọrụ

Your ASD LED Flood Light offers versatile operation modes and customizable settings.

1. Selecting Lighting Modes

Use the control dial on the motion sensor to select one of three operating modes:

N'OGE: The light functions as a standard lamp, staying on continuously without motion sensing.
DUSK TO DAWN (D2D): The light automatically turns on at dusk and off at dawn, based on ambient light levels detected by the photocell.
UTgbọala: The light turns on and off based on motion detection and your selected lux requirement settings (L - Low sensitive / M - Middle sensitive / H - High sensitive).

Lighting mode selection dial and examples

Foto: Diagram illustrating the control dial for selecting ON TIME, D2D (Dusk to Dawn), and AUTO modes, with visual examples of how the light behaves in each setting.

Built-in Dusk to Dawn photocell operation

Foto: The flood light operating at night, demonstrating the built-in dusk-to-dawn photocell functionality which automatically activates the light when ambient light levels drop.

2. Motion Sensor Settings

The integrated 180° motion sensor has a detection range of up to 60 feet. In AUTO mode, you can adjust the sensitivity:

L (Low Sensitive): Less sensitive to movement, ideal for areas with minimal activity.
M (Middle Sensitive): Mmetụta nkịtị maka ojiji nkịtị.
H (High Sensitive): Most sensitive to movement, suitable for high-traffic areas or enhanced security.

You can also adjust the 'Hold Time' (how long the light stays on after motion is detected) and 'Ambient Light' (lux level at which the sensor becomes active) settings using the respective dials on the sensor unit.

Foto: A person walking in front of a garage, demonstrating the 180° detection angle of the high-sensitive motion sensor, which activates the flood light.

Foto: Diagram showing the flexible settings for the motion sensor, including Ambient Light (less than 10 lux), Hold Time (10 seconds to 10 minutes), and Detection Motion Speed (0.6-1.5 m/s), with a visual representation of the 60ft detection distance.

3. Color Temperature (CCT) Adjustment

The fixture offers 5 selectable color temperatures, ranging from warm to daylight. To change the CCT, locate the CCT switch on the fixture and slide it to your desired setting:

2700K: Ọcha dị nro
3000K: Ọcha na-ekpo ọkụ
3500K: Na-anọpụ iche na-acha ọcha
4000K: Ọcha dị jụụ
5000K: Ìhè ụbọchị

Foto: Visual representation of the 5 CCT options (2700K, 3000K, 3500K, 4000K, 5000K) and how they appear when the flood light is active, allowing users to select their preferred light ambiance.

Nlekọta

Mmezi mgbe niile na-eme ka ọkụ idei mmiri gị rụọ ọrụ nke ọma ma na-adịte aka.

Nhicha: Jiri ihe dị nro hichaa ihe nkwụnye ahụ mgbe niile, damp Ákwà. Ejila ihe nhicha ma ọ bụ ihe mgbaze, n'ihi na ha nwere ike imebi ihe ndị dị na ya ma ọ bụ ihe ndị dị na eletriki.
Nyocha: Annually inspect the wiring and mounting hardware for any signs of wear, corrosion, or loosening. Tighten connections as needed.
Igwe ihe mmetụta: Keep the motion sensor lens clean and free from obstructions (e.g., dirt, spiderwebs) to ensure proper operation.

Nchọpụta nsogbu

If you experience issues with your flood light, refer to the following common problems and solutions:

Nsogbu	Ihe nwere ike ime	Ngwọta
Ìhè anaghị agbanwuo.	No power, faulty wiring, incorrect mode setting, photocell detecting too much light.	Check circuit breaker. Verify wiring connections. Ensure mode is set to AUTO or ON TIME. Cover photocell to test if it's detecting light.
Ìhè na-anọgide na-enwu.	Mode set to ON TIME or D2D, constant motion detected, sensor sensitivity too high.	Switch mode to AUTO. Reduce motion sensor sensitivity (L setting). Check for constant heat sources or movement in detection zone.
Motion sensor not detecting movement.	Sensor obstructed, sensitivity too low, incorrect ambient light setting.	Clean sensor lens. Increase sensor sensitivity (H setting). Adjust ambient light setting on the sensor. Ensure sensor is aimed correctly.
Ìhè flickers ma ọ bụ na-ada ada.	Loose wiring, voltage fluctuations, incompatible dimmer (if applicable).	Check and tighten all wiring connections. Consult an electrician for voltage issues. This fixture is not designed for use with dimmers.

Nkọwapụta ngwaahịa

Akara: ASD
Aha nlereanya: SFL A-SFL-20BK
Nọmba akụkụ: A-SFL-20BK
Agba: Black with Motion Sensor
Ihe: Aluminom, polycarbonate
Ụdị: Oge a
Ụdị Nkụnye ọkụ: Ìhè idei mmiri
Ụdị ụlọ: Oghere dị n'èzí
Akụkụ ngwaahịa: 10.24"L x 4.45"W x 6.81"H
Ihe eji eme ihe maka ngwaahịa: N'èzí
Ojiji ime ụlọ/n'èzí: N'èzí
Isi mmalite ike: Hardwired
Ụdị nwụnye: Oke ugwu
Atụmatụ pụrụ iche: 180° 3 Modes Motion Sensor and Photocell, 5 Color Temperature Options, Beam Angle 100°, Rotatable Light Heads for Directional Light Control, Wet Locations Rated (IP65)
Usoro njikwa: Remote (referring to sensor adjustments, not a physical remote)
Ụdị isi iyi ọkụ: Ikanam
Voltage: 120 volts
Ụzọ ọkụ: Enwere ike idozi
Ibu ihe: 1 pound
Wattage: 20 watt
Ọnụọgụ nkeji: 1.0 Ọnụ
Ụdị nkwụnye: Ugwu mgbidi
Ụdị nkwụnye: Enweghị ike iwepụ
UPC: 810128113458
Asambodo: UL, DLC Premium
Ogologo ndụ: awa 145,000

Ozi akwụkwọ ikike

This ASD LED Motion Sensor Outdoor Flood Light (Model A-SFL-20BK) is covered by a Akwụkwọ ikike dị afọ 5 site na ụbọchị ịzụrụ. Akwụkwọ ikike a na-ekpuchi ntụpọ dị na ngwa na arụ ọrụ n'okpuru ojiji nkịtị. Ọ naghị ekpuchi mmebi sitere na nrụnye na-ezighi ezi, ihe mberede, iji eme ihe n'ụzọ na-ezighi ezi, mmegbu, ma ọ bụ mgbanwe na-akwadoghị.

For warranty claims or further details, please retain your proof of purchase and contact customer support.

Nkwado ndị ahịa

If you have any questions, require technical assistance, or need to report an issue with your ASD LED Motion Sensor Outdoor Flood Light, please contact our customer support team.

Please visit the official ASD website for the most current contact information, including phone numbers, email addresses, and online support resources.

Akụrụngwa dị n'ịntanetị: Visit the ASD Store on Amazon

	ASD LED Linear High Bay nwere Q-Base: Nkọwapụta na Nduzi Nwụnye Nduzi zuru oke maka ASD's LED Linear High Bay nwere Q-Base, nkọwapụta ngwaahịa, atụmatụ, ntuziaka nrụnye, na ozi gbasara ịtụ ihe. Na-ekpuchi arụmọrụ ike, ike a họọrọ na okpomọkụ agba, nhọrọ ihe mmetụta mmegharị, na nkwado batrị.
	Ngwa ASD LED Downlight Retrofit: A na-ahọrọ agba, a na-ebelata ya, ọkụ dị irè maka ike. Chọpụta ASD LED Downlight Retrofit Kit, nke nwere imewe ochie, nhọrọ agba 5CCT a pụrụ ịhọrọ, obere ntụpọ, na ntinye dị mfe. Ọ dị mma maka ebe mmiri dị, yana ogologo ndụ awa 50,000 na asambodo UL. Chọpụta nkọwapụta na ozi ịtụ ihe.
	Ngwa ASD LED Na-enweghị Azụ̀ Na-anaghị Arụ Ọrụ - Nkọwapụta Ngwaahịa na Ntuziaka Nwụnye Nkọwapụta zuru ezu, atụmatụ, na ntuziaka ntinye maka ihe eji ekpuchi vapor nke ASD LED nke na-enweghị seamless. Gụnyere ozi gbasara imewe, nkwado batrị, nhọrọ agba na ike, ngwa, na ihe ndị ọzọ.tages, ngosipụta ngwaahịa, ozi ịtụ ihe, nkọwapụta eletriki na gburugburu ebe obibi, mgbakwunye, ọdịnaya ngwugwu, na ozi ihe mmetụta mmegharị.
	ASD LED Trimless Downlight - Nkọwapụta Ngwaahịa, Ntinye, na Nduzi Nduzi Nduzi zuru oke maka ASD LED Trimless Downlights, nke gụnyere atụmatụ ngwaahịa, nkọwapụta zuru ezu, ntuziaka ntinye, na ozi gbasara ịtụ ihe. Atụmatụ gụnyere CCT nwere ike ịhọrọ agba, ọkwa CRI dị elu, IC na Wet Location, na ogologo ndụ.
	ASD LED Gburugburu ọkụ na-enwu gburugburu ya na igbe njikọ - Nkọwapụta Ngwaahịa na Ntuziaka Nwụnye Nkọwapụta zuru ezu, atụmatụ, na ntuziaka nwụnye maka ASD LED Round Downlight nwere Junction Box. Mụta maka imewe ya, arụmọrụ ike ya, asambodo ya, na ozi gbasara ịtụ ya.
	ASD LED Mgbidi Mgbidi Mpụta: Ọgbara ọhụrụ, Agba a na-ahọrọ, Ọkụ Foto Chọpụta ASD LED Mgbidi Mpụta, nke nwere imewe ọgbara ọhụrụ, iko doro anya, akụkụ ìhè 180°, na mbelata triac. Na-enye CCT nke a na-ahọrọ agba (3000K/4000K/5000K) na sel foto arụnyere n'ime ya nke anyanwụ na-acha ruo ụtụtụ. A na-enye ya ọkwa maka ebe mmiri dị mmiri mmiri, na-adịgide adịgide, yana ndụ awa 50,000 na akwụkwọ ikike afọ 5. ETL kwadoro.

ASD A-SFL-20BK