Ntuziaka Onye Ọrụ nke Igwe Ntucha Mkpofu VF1600 EP

1. Okwu mmalite

This manual provides important information regarding the safe operation, installation, and maintenance of the Eliminator Lighting VF1600 EP Fog Machine. Please read and understand all instructions thoroughly before operating this device. Retain this manual for future reference.

The Eliminator Lighting VF1600 EP is a 1650W mobile DMX fog machine designed to produce atmospheric fog effects. It features a high-efficiency heater block, LED heating indicators, a low fog fluid shut-off sensor, and includes both wired and wireless remote controls for versatile operation.

2. Ozi nchekwa

Ịdọ aka ná ntị: To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture. Do not spill water or other liquids into or onto your unit. This device is for adult supervision only. Do not operate without liquid. Keep this device away from rain and moisture. Only use high-quality, water-based fog fluid. No user-serviceable parts inside. Never operate the device when it is hot after running.

• Jikọọ mgbe niile na sekit gbadoro ụkwụ.
• Gbaa mbọ hụ na isi iyi ahụ dabara na vol achọrọtage (AC 120V/60Hz, 15A).
• Akwụsịla oghere ikuku.
• Allow adequate space around the unit for proper ventilation.
• Do not touch the nozzle during operation or immediately after use, as it will be hot.
• Use only Eliminator Lighting approved water-based fog fluid. Other fluids may cause clogging, poor performance, or health hazards.
• If the unit fails to operate correctly, discontinue use immediately.
• Debe ebe ụmụaka na-apụghị iru.

3. Ihe ngwugwu

Verify that all components listed below are present and in good condition upon opening the package:

• Eliminator Lighting VF1600 EP Fog Machine
• VFEPT6 Wired Timer Remote Control
• VFEPR2 Wireless Remote Control
• Igwe ọkụ ọkụ
• Akwụkwọ ntuziaka (akwụkwọ a)

4. Ngwaahịa gafereview

Familiarize yourself with the various parts and controls of the VF1600 EP Fog Machine.

Foto 4.1: N'ihu na akụkụ view of the Eliminator Lighting VF1600 EP Fog Machine. This image shows the main body of the fog machine, including the output nozzle, the fluid tank cap, and the carrying handle.

Foto 4.2: Rear panel of the Eliminator Lighting VF1600 EP Fog Machine. This view highlights the power switch, power input, manual fog button, DMX input/output ports, wireless remote input, and DIP switches for DMX addressing.

4.1 Njikwa azụ azụ na njikọ

• POWER ON/OFF Switch: Isi mgba ọkụ maka otu.
• IKE NA: AC 120V/60Hz, 15A power input.
• MANUAL IN: Input for the VFEPT6 wired remote control.
• FOG Button: Manual trigger for fog output.
• DMX 512 IN/OUT: 3-pin DMX connections for external DMX controller.
• IKWU: Input for the VFEPR2 wireless remote receiver.
• Mgbanwe DIP: Used for setting the DMX address.
• Mmanụ mmiri: 2.3 Liter capacity, non-removable. Features an LED heating indicator system:
  • Uhie: kpo oku
  • Akwụkwọ ndụ akwụkwọ ndụ: Njikere iji
  • Na-egbuke egbuke: Fog fluid tank is low

4.2 Njikwa anya

Foto 4.3: VFEPT6 Wired Timer Remote Control. This remote features controls for interval, duration, output level, and continuous fog, along with a timer function.

Foto 4.4: VFEPR2 Wireless Remote Control. This compact remote provides convenient wireless activation of the fog machine.

5. Nhazi

1. Nkwanye: Place the fog machine on a flat, stable surface in a well-ventilated area. Ensure there is adequate space around the unit for heat dissipation and fog dispersion. Do not place directly on carpet or other flammable materials.
2. Fluid Fill: Unscrew the cap of the fluid tank and carefully pour high-quality, water-based fog fluid into the tank. Do not overfill. Securely replace the cap. The tank capacity is 2.3 liters.
3. Njikọ ike: Connect the power cable to the POWER IN socket on the rear panel and then to a grounded electrical outlet (AC 120V/60Hz, 15A).
4. Remote Connection (Optional):
   • For the VFEPT6 wired remote, plug its connector into the MANUAL IN port.
   • For the VFEPR2 wireless remote, ensure the receiver is connected to the WIRELESS port.
5. Njikọ DMX (Nhọrọ): If using DMX control, connect a DMX cable from your DMX controller to the DMX IN port on the fog machine. If linking multiple DMX devices, connect from DMX OUT to the next device's DMX IN. Set the DMX address using the DIP switches as per your DMX system requirements.

6. Ntuziaka ọrụ

1. Ike Na: Flip the POWER ON/OFF switch to the "ON" position. The LED indicator on the fluid tank will illuminate red, indicating the unit is heating up.
2. Kpoo ahụ ọkụ: Allow approximately 3 minutes for the unit to reach operating temperature. The LED indicator will turn green when the machine is ready to produce fog. If the LED flashes, the fluid tank is low and needs refilling.
3. Mmepụta Fog:
   • Akwụkwọ ntuziaka: Press the FOG button on the rear panel for immediate fog output.
   • Wired Remote (VFEPT6): Use the controls on the VFEPT6 remote to set interval, duration, output level, or continuous fog. Refer to the VFEPT6 remote's specific instructions for detailed programming.
   • Wireless Remote (VFEPR2): Press the button on the VFEPR2 remote to activate fog output wirelessly.
   • Njikwa DMX: If connected to a DMX controller, operate the fog machine via your DMX software or console. Consult your DMX controller's manual for channel assignments and control parameters.
4. Na-ekpo ọkụ: After a period of fog output, the unit may need to reheat. The LED indicator will turn red again. Reheating time is approximately 15 seconds.
5. Gbanyụọ: When finished, turn the POWER ON/OFF switch to the "OFF" position and disconnect the power cable from the outlet. Allow the unit to cool completely before moving or storing.

Foto 6.1: The Eliminator Lighting VF1600 EP Fog Machine in operation, emitting a dense fog. This demonstrates the machine's capability to fill a space with atmospheric effects.

7. Nlekọta

Regular maintenance ensures optimal performance and extends the lifespan of your fog machine.

• Ogo mmiri mmiri: Always use high-quality, water-based fog fluid. Using oil-based fluids or other unauthorized liquids will damage the unit and void the warranty.
• Nhicha: Periodically clean the exterior of the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Nhicha nozzle: If the fog output appears weak or inconsistent, the nozzle may be partially clogged. Consult a qualified technician for cleaning or servicing. Do not attempt to disassemble the unit yourself.
• Nchekwa: When not in use for extended periods, drain any remaining fog fluid from the tank. Store the unit in a cool, dry place.

8. Nchọpụta nsogbu

9. Nkọwapụta

10. Akwụkwọ ikike na nkwado

For warranty information or technical support, please refer to the official Eliminator Lighting websaịtị ma ọ bụ kpọtụrụ onye na-ere gị ikike. Debe nnata nzụta gị ka ihe akaebe nke ịzụrụ.

Using non-approved fog fluid or attempting unauthorized repairs will void the product warranty.