ErGear Dual Monitor Desk Mount EGCM13B Instruction Manual

Okwu mmalite

Thank you for choosing the ErGear Dual Monitor Desk Mount. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your new monitor mount. Please read this manual thoroughly before installation and keep it for future reference.

Ozi nchekwa dị mkpa

Please ensure all instructions are read and understood before assembly and use. If you have any questions, please contact customer service. Failure to follow these instructions may result in property damage, serious injury, or death.

Verify that your monitor's weight and VESA pattern are within the specified limits.
Do not exceed the maximum load capacity of 26.5 lbs per arm.
Ensure the mounting surface (desk) is strong enough to support the combined weight of the mount and monitors.
Jiri naanị ngwaike enyere.
Debe obere akụkụ n'ebe ụmụaka nọ.

Nkọwapụta

Ụdị: EGCM13B
Ndakọrịta nha ihuenyo: 13 ruo 34 sentimita asatọ
Weight Capacity (per arm): Ruo 26.5 lbs
Ndakọrịta VESA: 75x75 mm, 100x100 mm
Arm Span: 33 sentimita asatọ
Ogologo osisi: 16.3 sentimita asatọ
Ụdị mmegharị: Tilt, Swivel, Rotation, Articulating
Akụkụ Tilt kacha elu: 90 ogo
Ihe: Alloy Steel
Agba: Nwa
Ụdị nkwụnye: Ugwu Tebụl (C-Cl)amp ma ọ bụ Grommet)
C-Clamp Ọkpụrụkpụ oche: 0.39"-3.15"
Grommet Mount Desk Thickness: 0.39"-2.17"
Grommet Hole Diameter: 0.47"-0.79"

Ihe ngwugwu

Please check that all parts are included and undamaged. If any parts are missing or damaged, please contact customer service.

Ogidi Isi nwere Desk Clamp/Isi Grommet
Abụọ Monitor Arms
Efere VESA (2x)
Mounting Hardware (screws, washers, tools)
Mpempe akwụkwọ njikwa eriri
Akwụkwọ ntuziaka

ErGear Dual Monitor Desk Mount components laid out — Image: All components of the ErGear Dual Monitor Desk Mount laid out, including the main pole, dual arms, VESA plates, and various hardware for assembly.

Ntọala na nwụnye

1. Desk Compatibility Check

Before installation, ensure your desk meets the following criteria:

Ihe: Recommended for wooden tables.
N'okpuru: Preferably free of beams or panels that may interfere with installation.
C-Clamp Ọkpụrụkpụ: 0.39"-3.15"
Grommet Mount Thickness: 0.39" - 2.17" (Hole Diameter: 0.47" - 0.79")

2. Monitor Compatibility Check

Each monitor must meet these conditions:

Nha ihuenyo: 13 ruo 34 sentimita asatọ
Arọ: Ruo 26.5 lbs
Oghere mbanye VESA: 75x75 mm or 100x100 mm apart on the back of the monitor.

Diagram showing VESA hole patterns on the back of a monitor — Image: Illustration of VESA mounting hole patterns (75x75mm and 100x100mm) on the back of a monitor, indicating where the mount attaches. It also shows how to remove a monitor's original stand.

3. Assemble the Pole with Clamp Nkwado

Choose either C-Clamp or Grommet installation based on your desk type.

Video: Demonstrates the installation process of the dual monitor desk mount, including assembling the pole with clamp support for both grommet and C-clamp methods. This video is provided by the seller.

Eserese na-egosi C-Clamp and Grommet mounting options — Image: Visual guide illustrating the two available mounting options: C-Clamp for desk edges and Grommet mount for desks with existing holes. Includes dimensions for compatible desk thickness and hole diameter.

Follow the detailed steps in the provided video and diagrams to securely attach the main pole to your desk using either the C-Clamp or Grommet method. Ensure all screws are tightened appropriately for stability.

4. Assemble the Arm and Pole Wire Clips

Attach the monitor arms to the main pole. Loosen the screw on the pipe clamp before installing the arm, then tighten it securely. Ensure the VESA plate side of the arm faces upwards. Install the cable management clips along the arms and pole.

5. Assemble VESA Plate and Monitor

Attach the VESA plate to the back of your monitor using the appropriate screws and washers. Ensure it is securely fastened.

6. Install the Monitor to the Swivel Arm

Carefully slide the monitor (with the attached VESA plate) onto the swivel arm. Secure it by tightening the locking screw. Adjust the screw with the Allen key to adjust the height of the VESA panel as needed (clockwise to lower, counter-clockwise to raise).

Image showing two monitors mounted on the ErGear Dual Monitor Desk Mount — Image: Two monitors securely mounted on the ErGear Dual Monitor Desk Mount, demonstrating a clean and organized workspace.

Ịrụ ọrụ na mmezi

The ErGear Dual Monitor Desk Mount offers versatile adjustments for optimal viewnkasi obi:

Ndozi elu: tọpụ clamp on the main pole to slide the arms up or down to your desired height. Re-tighten the clamp nke ọma.
Gbaa: Adjust the monitor's vertical angle by tilting it +/-45 degrees to reduce glare and eye strain.
Swivel: Rotate the monitor horizontally +/-90 degrees for easy screen sharing or viewing si n'akụkụ dị iche iche.
Ntughari: Tụgharịa ihe nlele ahụ ruo ogo 360 iji gbanwee n'etiti nhazi ala na eserese.
Arm Extension/Retraction: The articulating arms allow you to extend or retract your monitors closer or further from you. Adjust the tension screws on the arm joints as needed to hold the desired position.

Diagram showing tilt, swivel, and rotation adjustments — Image: Visual representation of the monitor's flexible adjustments, including +/-45° tilt, +/-90° swivel, and 360° rotation, allowing for ergonomic positioning.

Nlekọta

Lelee skru na njikọ niile iji hụ na ha kwụsiri ike na nchekwa.
Clean the mount with a soft, damp akwa . Zere ndị na-ehicha ihe na-ekpo ọkụ.
Do not disassemble the mount unless instructed to do so.

Nchọpụta nsogbu

Ihe nlele anaghị adị larịị: Ensure the VESA plates are correctly aligned and tightened. Adjust the small bolts on the tilt head to fine-tune alignment.
Monitors sag or do not hold position: Tighten the tension screws on the arm joints. Refer to the assembly instructions for specific locations.
Ugwu ahụ adịghị mma: Double-check that the C-Clamp or Grommet mount is securely fastened to the desk and all screws are fully tightened. Ensure your desk meets the thickness requirements.

Akwụkwọ ikike na nkwado

For warranty information or technical support, please refer to the product packaging or contact ErGear customer service directly. Keep your purchase receipt as proof of purchase.

	ErGear EGESD7 Electric Standing Desk - Akwụkwọ Ntuziaka Ntinye Ntuziaka ntinye zuru ezu maka tebụl eletriki ErGear EGESD7, nke nwere nhazi elu, ntọala ebe nchekwa, na elu 63x28 inch. Gụnyere nkọwapụta na ntuziaka ntọala maka ịmepụta ebe ọrụ ergonomic.
	Akwụkwọ ntuziaka ErGear Electric Standing Desk Guide - Mgbakọ na ntuziaka ọrụ Akwụkwọ ntuziaka zuru oke maka ErGear Electric Standing Desk (Models EGESD8B, EGESD8V). Mụta otu esi ejikọta, rụọ ọrụ, na idozi nsogbu na tebụl gị nke a na-agbanwe agbanwe maka ịdị elu.
	Ntuziaka Onye Ọrụ na Nduzi Mgbakọ Ergear Electric Standing Desk MSESD202-80A Nduzi zuru oke maka Ergear Electric Standing Desk (Model MSESD202-80A), gụnyere ntuziaka mgbakọ, ozi nchekwa, ọrụ nke njikwa, na nsogbu nsogbu.
	Ergear Electric Standing Desk Assembly and User Manual Comprehensive guide for assembling and using the Ergear 48" / 63" Electric Standing Desk (Models EGESD5B, EGESD5V, EGESD5N, EGESD7B, EGESD7V, EGESD7N). Includes step-by-step instructions, specifications, controller functions, and troubleshooting error codes.
	Ntuziaka ntinye nke oche eletriki ErGear nke a na-agbanwe agbanwe Ntuziaka ntinye maka ErGear Height Adjustable Electric Standing Desk (55 x 28 inch). Akwụkwọ ntuziaka a na-enye ntuziaka nzọụkwụ site na nzọụkwụ maka nchikọta, ọrụ, na nsogbu nke tebụl ErGear sit-stand gị.
	ErGear Desk Monitor Arm EGDMA69-SS: Installation Guide and Features Comprehensive guide for installing and using the ErGear Desk Monitor Arm (EGDMA69-SS). Features include VESA compatibility, adjustable gas spring, swivel, tilt, and rotation for optimal monitor positioning. Includes safety information and step-by-step assembly instructions.

ErGear EGCM13B