1. Okwu mmalite
The OONO F-1060 is an AC/DC 12V Single Pole Single Throw (SPST) latching relay module designed for various control applications. A key feature of this module is its power-off memory, which ensures that the output switch status remains unchanged even if the power supply is interrupted. This manual provides essential information for the safe and effective installation, operation, and maintenance of your F-1060 relay module.
2. Ozi nchekwa
Please read and understand all safety instructions before installing or operating this device. Failure to follow these instructions may result in electrical shock, fire, or property damage.
- Kwụpụ ike: Always disconnect power to the circuit before performing any installation, wiring, or maintenance.
- Ndị ọrụ tozuru oke: Installation and wiring should be performed by qualified personnel familiar with electrical systems and local electrical codes.
- Voltage na ọkwa dị ugbu a: Agafela voltage and current ratings of the relay module.
- Mkpọchi kwesịrị ekwesị: Ensure the module is installed in a suitable enclosure to protect it from environmental factors and accidental contact.
- Wiring: Use appropriate wire gauges for the current load and ensure all connections are secure.
3. Ngwaahịa gafereview
The OONO F-1060 is a compact, pre-wired latching relay module housed in a durable polycarbonate plastic enclosure. It features a Single Pole Single Throw (SPST) output switch and accepts AC/DC 12V input control signals. The module is designed for easy integration into various electrical systems, offering reliable power-off memory functionality.
Foto 3.1: N'ihu view of the OONO F-1060 Latching Relay Module, showing the product label with input and contact ratings, and wiring diagram for the internal relay.
4. Nkọwapụta
Foto 4.1: Detailed dimensional drawing of the OONO F-1060 module, including measurements in millimeters and inches, and NPT 1/2" nipple details.
| Oke | Uru |
|---|---|
| Nlereanya | F-1060 |
| Ntinye akara njikwa | AC / DC 12V |
| Supported Input Types | AC, DC COM+ (Sink NPN), DC COM- (Source PNP) |
| Input Current (12V AC/DC) | 84mA |
| Output Switch Type | SPST (Otu Otu Osisi Otutu) |
| Contact Rating (AC) | 20A / 250VAC |
| Contact Rating (DC) | 20A / 30VDC |
| Ngwa kọntaktị | Ọlaọcha |
| Ihe mkpuchi | Polycarbonate Plastic |
| Ịkwanye | NPT 1/2" mounting nipple, Two screw mounting holes |
| Ụdị njikọ | Ekwenyere |
| Akụkụ (Ihe dị ka) | 5.59 x 2.91 x 1.77 inch (Ngwugwu) |
| Ibu (Ihe dị ka.) | ounce asatọ (Ngwugwu) |
5. Ihe ngwugwu
Hụ na ihe niile dị ma ghara imebi emebi mgbe e meghere ngwugwu ahụ.
Foto 5.1: The OONO F-1060 Latching Relay Module shown with its pre-wired leads, NPT 1/2" zinc alloy conduit locknut, and two M3x50mm mounting screws.
- 1x OONO F-1060 Latching Relay Module (pre-wired)
- 1x NPT 1/2" Zinc alloy conduit locknut
- 2x M3x50mm kposara
6. Ntọala na nwụnye
Follow these steps for proper installation of the relay module.
6.1 Na-arịgo
- The module features a NPT 1/2" mounting nipple, allowing flexible installation with a junction box or outlet box. Secure it using the provided zinc alloy conduit locknut.
- Two screw mounting holes are provided for fixing the module to a wall or wooden board using the supplied M3x50mm screws.
Foto 6.1: Examples demonstrating how the OONO F-1060 module can be installed within a standard electrical junction box using its NPT nipple and locknut.
6.2 Ntuziaka waya
Refer to the wiring diagrams below for connecting the input control signal and the load. Ensure all connections are tight and insulated.
Foto 6.2: Comprehensive wiring diagrams illustrating connections for DC COM+ (Sink NPN), DC COM- (Source PNP), and AC input control signals. Each diagram shows the connection of the BLU ON, GRN OFF, YLW COM, RED, and BLK wires to the power source, control inputs, and the load.
- Input Control Wires:
- BLU ON: Connect to the positive control signal to turn the relay ON.
- GRN OFF: Connect to the positive control signal to turn the relay OFF.
- YLW COM: Common wire for the input control signal.
- Output Switch Wires (SPST):
- Uhie: One side of the SPST switch.
- BLK: The other side of the SPST switch.
- Njikọ Ibu Ibu: Connect your load (e.g., light, motor) in series with the RED and BLK wires and the power source for the load.
- Ụdị akara ntinye: The module supports AC, DC COM+ (Sink NPN), or DC COM- (Source PNP) input control signals. Ensure your control signal matches the module's requirements.
7. Ntuziaka ọrụ
The OONO F-1060 is a latching relay, meaning it maintains its state (ON or OFF) until a new control signal is received, even if power to the control circuit is removed.
- Na-agbanye: Apply a momentary AC/DC 12V signal between the BLU ON wire and the YLW COM wire. The relay will switch to the ON state and remain ON.
- Na-agbanyụ: Apply a momentary AC/DC 12V signal between the GRN OFF wire and the YLW COM wire. The relay will switch to the OFF state and remain OFF.
- Ebe nchekwa gbanyụọ: If the main power supply to the module is interrupted, the relay's last state (ON or OFF) will be preserved. When power is restored, the relay will resume its previous state without requiring a new control signal.
8. Nlekọta
The OONO F-1060 relay module is designed for reliable operation with minimal maintenance. However, periodic checks can help ensure its longevity and performance.
- Nlele anya: Lelee modul na wiring ya maka akara ọ bụla mebiri emebi, njikọ rụrụ arụ, ma ọ bụ corrosion.
- Nhicha: If necessary, gently clean the exterior of the module with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- Ọnọdụ gburugburu: Gbaa mbọ hụ na gburugburu ebe ọrụ ka dị n'ime oke okpomọkụ na iru mmiri akọwapụtara iji gbochie ọdịda akaghi aka.
9. Nchọpụta nsogbu
If you encounter issues with your OONO F-1060 relay module, refer to the following troubleshooting guide:
| Nsogbu | Ihe nwere ike ime | Ngwọta |
|---|---|---|
| Relay does not switch ON/OFF | Incorrect wiring of control signals No control signal present Mgbama njikwa voltage incorrect (not 12V) Faulty control switch/source | Verify wiring against diagrams (Figure 6.2). Check for presence of 12V AC/DC signal. Measure control signal voltage. Test control switch/source independently. |
| Load does not receive power when relay is ON | Incorrect load wiring Load power supply issue Overloaded relay contacts Faulty load | Check load wiring. Ensure power source for load is active. Verify load power supply. Ensure load current does not exceed 20A. Test load independently. |
| Relay does not maintain state after power cycle | This module is designed to maintain state. If it fails, the module may be faulty. | Kpọtụrụ nkwado ndị ahịa maka enyemaka. |
| Module appears damaged | Mmetụta anụ ahụ Mfefetage/overcurrent | Disconnect power immediately. Do not attempt to repair. Contact customer support. |
10. Akwụkwọ ikike na nkwado
OONO products are manufactured to high-quality standards. For warranty information, technical support, or service inquiries, please refer to the product packaging or contact your retailer. Please have your product model number (F-1060) available when contacting support.
