FLYLINKTECH Car Jump Starter User Manual

1. Okwu mmalite

The FLYLINKTECH CF600 Car Jump Starter is a portable, powerful device designed to start vehicles with dead batteries. It features a 1500A peak current, suitable for gasoline engines up to 8.0 liters and diesel engines up to 6.0 liters. Beyond its primary function, it also serves as a 16000mAh power bank for charging electronic devices and includes a multi-function LED light for various utility purposes. This manual provides essential information for safe and effective operation, maintenance, and troubleshooting of your jump starter.

Figure 1: FLYLINKTECH Car Jump Starter with smart clamps and charging cables.

2. Ozi nchekwa

Please read all safety warnings and instructions carefully before using this product. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

• Always ensure the jump starter is fully charged before use.
• Do not attempt to jump start a vehicle if the jump starter or cables are damaged.
• Jikọọ clamps correctly: Red clamp to positive (+) terminal, Black clamp to negative (-) terminal. Reverse polarity can cause damage.
• Ejikọtala ihe dị mma na nke na-adịghị mma clamps ọnụ.
• Debe ebe ụmụaka na-apụghị iru.
• Ewepụla ngwaahịa a na mmiri ozuzo ma ọ bụ ọnọdụ mmiri.
• Akpọsakwala otu ahụ. Kpọtụrụ ndị ọrụ ruru eru ọrụ niile.
• Ensure the vehicle's ignition is off before connecting the jump starter.
• Remove the jump starter from the vehicle battery within 30 seconds after the engine starts.
• Njirimara ngwaọrụ 8 Smart Safe Clamp Nchedo, including reverse polarity, overcharge, short circuit, high temperature, over voltage, and over current protection. However, always exercise caution.

Figure 2: Intelligent clamps with built-in safety features for protection against common errors.

3. Ihe ngwugwu

Chọpụta na ihe niile dị na ngwugwu:

• FLYLINKTECH Car Jump Starter Unit
• Smart jumper Clamps (Uhie na Oji)
• Igwe nchaji USB
• EC5 Female Adapter
• Akwụkwọ ntuziaka onye ọrụ (Akwụkwọ a)
• Akpa nchekwa

4. Ngwaahịa gafereview

The FLYLINKTECH Car Jump Starter is a versatile device designed for emergency vehicle starting and portable power.

Akụkụ ndị bụ isi:

• Mmalite dị ike: 1500A peak current, capable of starting 12V vehicles with up to 8.0L gasoline or 6.0L diesel engines.
• Ụlọ akụ ọkụ nwere ike ibugharị: 16000mAh capacity with two USB ports, including one QC3.0 port for fast charging mobile phones, tablets, and other USB-powered devices.
• Multi-Function LED Light: Features Torch, SOS, Quick Flash, and Blue & Red Flashing modes for illumination and emergency signaling.
• Smart Safety Clamps: Equipped with 8 intelligent protections: reverse polarity, overcharge, short circuit, high temperature, over voltage, and over current.
• EC5 Adapter and Safety Hammer: Includes an EC5 female adapter for powering 12V car accessories (e.g., car cleaner, air pump) and a built-in safety hammer for emergency window breaking.
• Kọmpat ma dị fechaa: Weighs approximately 1kg with dimensions of 18.5 x 9.5 x 4.5 cm, making it easy to store and carry.

Figure 3: Compact dimensions and lightweight design of the jump starter.

Figure 4: Engine compatibility for the 1500A peak current jump starter.

5. Ntọlite ​​na Nchaji mbụ

Before first use, fully charge the jump starter.

1. Connect the provided USB charging cable to the jump starter's input port.
2. Connect the other end of the USB cable to a 5V/2A or higher USB wall adapter (not included) or a computer USB port.
3. The LED indicator lights on the jump starter will illuminate to show the charging progress. All four lights will be solid when fully charged.
4. A full charge typically takes several hours. It is recommended to charge the unit every 3-6 months to maintain battery health, even if not in use.

6. Ntuziaka ọrụ

6.1. Malie Malite Ụgbọala

Ensure the jump starter is sufficiently charged (at least 3-4 indicator lights).

1. Kwadebe ụgbọ ala: Turn off the vehicle's ignition and all electrical loads (headlights, radio, air conditioning, etc.). Engage the parking brake.
2. Jikọọ Clamps to Jump Starter: Fanye plọg na-acha anụnụ anụnụ nke smart jumper clamps into the jump starting port on the jump starter unit. Ensure it is fully inserted. The indicator light on the clamps should flash green and red, indicating it's ready.
3. Jikọọ Clamps to Battery:
   • Jikọọ Uhie (+) clamp gaa na njedebe dị mma (+) nke batrị ụgbọala ahụ.
   • Jikọọ OJI (-) clamp gaa na njedebe nke batrị ụgbọala ahụ na-adịghị mma (-).
   If the connection is correct, the indicator light on the clamps will turn solid green. If it flashes red or beeps, check for reverse polarity or short circuit and correct the connection.
4. Malite ụgbọ ala: Return to the vehicle and start the engine within 30 seconds.
5. Wepu Clamps: Once the engine starts, immediately remove the clamps from the vehicle battery, then disconnect the clamps from the jump starter unit.

Figure 5: Step-by-step guide for jump starting a vehicle.

6.2. Iji dị ka Power Bank

The jump starter can charge various electronic devices via its USB output ports.

1. Connect your device's USB charging cable to one of the USB output ports on the jump starter.
2. Connect the other end of the cable to your electronic device (e.g., smartphone, tablet, Bluetooth speaker).
3. The jump starter will automatically begin charging your device. The QC3.0 port offers faster charging for compatible devices.

Figure 6: The jump starter's power bank functionality and EC5 adapter use.

6.3. Iji ọkụ LED

The built-in LED light offers multiple modes for different situations.

1. Press and hold the power button for 3 seconds to turn on the LED light (Torch mode).
2. Press the power button briefly to cycle through the modes: Torch → SOS → Quick Flash → Blue & Red Flash → Off.
3. Press and hold the power button again for 3 seconds to turn off the LED light from any mode.

Figure 7: The multi-function LED light in operation, illustrating its various modes.

7. Nlekọta

Proper maintenance ensures the longevity and optimal performance of your jump starter.

• Na-ebugharị: Recharge the unit after each use. If not used frequently, recharge every 3-6 months to prevent deep discharge and extend battery life.
• Nhicha: Wipe the unit with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
• Nchekwa: Store the jump starter in a cool, dry place, away from direct sunlight, moisture, and extreme temperatures. Keep it in its provided storage case for protection.
• Nlekọta batrị: The internal lithium-ion battery is not user-replaceable. Do not attempt to open the unit.

8. Nchọpụta nsogbu

If you encounter issues with your FLYLINKTECH Car Jump Starter, refer to the following common problems and solutions:

9. Nkọwapụta

Mara: Nkọwapụta ga-agbanwe na-enweghị ọkwa.

10. Akwụkwọ ikike na nkwado

FLYLINKTECH products are manufactured to high-quality standards. For information regarding warranty coverage, technical support, or service inquiries, please refer to the warranty card included with your product or visit the official FLYLINKTECH websaịtị.

When contacting support, please have your product model number (CF600) and purchase details readily available.