Mgbidi Mpụga Mpụga Mpụga Mpụga Paulmann 94453 Capea LED nke dị n'èzí Lamp ya na akwụkwọ ntuziaka ntuziaka Motion Detector

Okwu mmalite

Thank you for choosing the Paulmann 94453 Capea LED Outdoor Wall Lamp. This manual provides essential information for the safe installation, operation, and maintenance of your new outdoor lighting fixture. Please read these instructions carefully before installation and retain them for future reference.

Image: The Paulmann Capea LED Outdoor Wall Lamp, showing the product itself and its retail packaging. The lamp is black, with a conical shade and an integrated motion sensor at the base.

Ntuziaka nchekwa dị mkpa

• Nchekwa Eletriki: Installation must be performed by a qualified electrician in accordance with local wiring regulations. Always switch off the main power supply before installation, maintenance, or repair.
• Ojiji n'èzí: This product is designed for outdoor use (IP44 rated). Ensure all connections are properly sealed to prevent water ingress.
• Ịkwanye: Mount the fixture securely on a stable surface. Do not install on flammable surfaces.
• Isi mmalite ọkụ: The LED light source is integrated and not replaceable by the user. Do not attempt to open or modify the light source compartment.
• Okpomọkụ: Ekpuchila lamp with insulating material. Ensure adequate air circulation around the fixture.

Ihe ngwugwu

Chọpụta na akụrụngwa niile dị tupu ịmalite nrụnye:

• 1x Paulmann Capea LED Outdoor Wall Lamp (Nlereanya 94453)
• Ntuziaka Mgbakọ
• Mounting hardware (screws, wall plugs) - (Assumed, as typical for wall lamps)

Nkọwa nka nka

Image: Technical drawing showing the dimensions of the Paulmann Capea LED Outdoor Wall Lamp: 153mm width, 165mm height, and 96mm depth.

Ntuziaka nwụnye

Tupu ịmalite: Ensure the main power supply to the installation area is switched off at the circuit breaker. Use appropriate tools and safety equipment.

1. Kwadebe Ebe Nkwanye: Choose a suitable wall location for the lamp, ensuring it is a stable surface and allows for proper wiring. Mark the drilling points for the mounting bracket.
2. Oghere egwu egwu: Drill holes at the marked points and insert appropriate wall plugs (if necessary).
3. Nkwado ugwu: Chekwaa ihe nkwado mgbago na mgbidi site na iji skru ndị enyere.
4. Wiring: Connect the electrical wires from your mains supply to the terminal block inside the lamp fixture. Ensure correct polarity (Live, Neutral, Earth) and secure all connections tightly. Refer to local electrical codes.
5. Tinye Lamp: Jiri nlezianya tinye lamp fixture to the mounting bracket, ensuring no wires are pinched. Secure the lamp n'ebe.
6. Weghachi ike: Ozugbo e mechara nrụnye ahụ ma njikọ niile dị nchebe, weghachite ike na isi ihe mgbawa sekit ahụ.

Image: The Paulmann Capea LED Outdoor Wall Lamp shown with its packaging, which illustrates basic installation steps and features like the motion sensor and IP44 rating.

Ntuziaka ọrụ

The Paulmann Capea LED Outdoor Wall Lamp features an integrated motion sensor for automatic operation.

Ntọala ihe mmetụta ngagharị

The motion sensor can be adjusted to suit your specific needs. Typically, there are controls for:

• Akụkụ nchọpụta: Approximately 90 degrees.
• Oke nchọpụta: 2-8 mita.
• Light Sensitivity (LUX): Determines the ambient light level at which the sensor activates the lamp.
  • ON < 20 Lux: Ndị lamp will turn on when motion is detected and the ambient light is below 20 Lux (dark conditions).
  • OFF > 20 Lux: Ndị lamp will remain off when the ambient light is above 20 Lux (daylight conditions).
• Oge GARA: Sets the duration the light remains on after motion is detected. Adjustable from approximately 5 seconds to 5 minutes.

Adjust these settings using the small dials or switches located on the motion sensor unit, usually found at the bottom of the lamp. Use a small screwdriver if necessary.

Image: A diagram illustrating the motion sensor's detection angle (90 degrees), range (2-8 meters), and light sensitivity settings (On < 20 Lux / Off > 20 Lux), along with the adjustable time duration (5 seconds - 5 minutes).

Foto: A nso nso view of the integrated motion sensor located at the base of the Paulmann Capea LED Outdoor Wall Lamp, showing its spherical lens.

Nlekọta

• Nhicha: Gbanyụọ ike tupu ị hichaa ya. Hichaa ike ahụ.amp jiri nwayọọ, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish or electrical components.
• Isi mmalite ọkụ: The LED light source is integrated and designed for long-term use (30,000 hours). It is not user-replaceable. If the LED fails, the entire fixture typically needs replacement.
• Nyocha: Nyochaa lamp for any signs of damage, loose connections, or wear. Address any issues promptly.

Nchọpụta nsogbu

Akwụkwọ ikike na nkwado ndị ahịa

Paulmann products are manufactured to high quality standards. This product comes with a 5-year guarantee, as indicated on the packaging. For warranty claims, technical assistance, or further inquiries, please contact your retailer or Paulmann customer support directly. Keep your proof of purchase for warranty purposes.

For more information, visit the official Paulmann websaịtị: www.paulmann.com

Ozi mkpofu

This product contains electronic components and an integrated LED light source. Do not dispose of it with general household waste. Please take it to a designated collection point for electrical and electronic equipment recycling in accordance with local regulations. Proper disposal helps prevent potential negative consequences for the environment and human health.