1. Okwu mmalite
Thank you for choosing the AQQA Submersible Aquarium Water Pump. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your pump. Please read these instructions thoroughly before use and retain them for future reference.
This submersible pump is designed for various aquatic applications, including aquariums, fish tanks, ponds, and hydroponic systems. It features an adjustable flow rate, ultra-quiet operation, and a high lift capability.
2. Ntuziaka nchekwa dị mkpa
- Nchekwa Eletriki: Gbaa mbọ hụ na ọkọnọ ọkụ voltage matches the pump's specifications (110V). Always unplug the pump from the power outlet before performing any maintenance, installation, or when not in use. Do not operate the pump with a damaged cord or plug.
- Ntinye mmiri: The pump must be completely immersed in water during operation to prevent dry burning, which can damage the motor and void the warranty.
- Okpomọkụ: The pump is equipped with an automatic power-off feature if the water temperature exceeds 85°C (185°F) to prevent overheating.
- Nkwanye: Position the pump securely on a flat surface within the water body. Ensure it is not obstructed by debris.
- Ụmụaka na anụ ụlọ: Keep the pump and its power cord out of reach of children and pets.
- Ezubere iji: This pump is designed for water circulation in aquatic environments. Do not use it for flammable liquids, corrosive chemicals, or other non-water applications.
3. Ihe ngwugwu
Nyochaa na etinyere ihe niile edepụtara n'okpuru na ngwugwu gị:
- AQQA Submersible Water Pump (Model AQ009, 265GPH 15W)
- 1/2 inch (13mm) Nozzle
- 5/8 inch (16mm) Nozzle
- Akwụkwọ ntuziaka onye ọrụ
Figure 3.1: AQQA Submersible Water Pump with included 13mm and 16mm nozzles.
Figure 3.2: Detailed diagram showing the water outlet, rotary adjustment button, protective water inlet cover, UL cable (6ft, 3-prong plug), handle, and shockproof rubber feet of the 15W pump.
4. Akụrụngwa Ngwaahịa
- Ọnụego mgbanwe mgbanwe: A rotary knob allows precise control over water flow.
- Ọrụ Ultra-Quiet: Equipped with a pure copper motor and ceramic shaft impeller for minimal noise.
- Ike ibuli elu: Capable of pumping water to a maximum height of 4.9 feet.
- Low Water Level Pumping: Designed to pump water down to 1 inch (approximately 1cm) from the bottom.
- 360° Bottom Suction: Efficiently removes dirt and impurities from the bottom of the tank.
- Atụmatụ nchekwa: IPX8 waterproof rating and automatic power-off protection against dry burning (if water temperature exceeds 85°C).
- Ihe owuwu na-adịgide adịgide: Made from Acrylonitrile Butadiene Styrene (ABS) with a durable pure copper motor.
- Ejikọkwara: A 90° rotating handle for convenient placement and removal.
Foto 4.1: Isi ihe dị mkpatages of the pump, including a silent ceramic shaft, rubber damping anti-slip feet, high-quality motor with anti-dry burning protection (auto power off above 85°C), and a hidden handle for convenience.
Figure 4.2: Illustrates the pump's IPX8 waterproof rating and its durable pure copper motor, highlighting its robust construction.
Figure 4.3: Demonstrates the pump's ability to operate effectively at a low water level, down to approximately 1 cm (0.4 inches) from the bottom.
5. Nhazi ntuziaka
- Họrọ Nozzle: Choose the appropriate nozzle (13mm or 16mm) for your application. The 13mm nozzle provides a narrower, stronger flow, while the 16mm nozzle offers a wider flow.
- Tinye Nozzle: Securely screw the selected nozzle onto the pump's water outlet.
- Nkwanye: Place the pump completely submerged in the water body (aquarium, pond, etc.). Ensure the pump is stable and not resting on loose debris.
- Njikọ ike: Once the pump is fully submerged, plug the 6ft power cord into a standard 110V electrical outlet.
Figure 5.1: The AQQA pump installed in an aquarium, illustrating the connection of different nozzle sizes for varied water flow requirements.
6. Ntuziaka ọrụ
- Ike Na: After proper setup and submersion, plug in the pump to start operation.
- Gbanwee ọnụego mmiri: Locate the 'FLOW VALVE' rotary knob on the side of the pump. Rotate the knob towards '+' to increase the water flow rate, or towards '-' to decrease it. Note that the flow cannot be completely turned off using this knob.
- Nleba anya: Observe the water flow and adjust as needed for your specific application.
- Gbanyụọ: To stop the pump, unplug it from the electrical outlet. Always unplug before removing the pump from water.
Ọgụgụ 6.1: nso nso view of the rotary switch (Flow Valve) on the pump, used to adjust the water flow rate from minimum to maximum.
7. Nlekọta
Regular cleaning and maintenance will ensure the longevity and optimal performance of your AQQA water pump.
- Kwụpụ ike: Always unplug the pump from the power source before any maintenance.
- Remove from Water: Carefully remove the pump from the water body.
- Kwụsa: Gently twist and pull the base of the pump to detach it. This will expose the impeller assembly.
- Igwe ọkụ dị ọcha: Remove the impeller and clean it thoroughly with a soft brush and clean water to remove any accumulated debris, algae, or mineral deposits. Ensure the impeller shaft is also clean.
- Clean Inlet Cover: Clean the protective water inlet cover to ensure unrestricted water flow.
- Gbakọtaghachi: Reassemble the pump by carefully placing the impeller back and securing the base. Ensure all parts are fitted correctly.
- Ugboro: Clean the pump regularly, especially if you notice a decrease in flow rate or increased noise.
Figure 7.1: Instructions for easy cleaning: regularly disassemble the base and clean the impeller to prevent blockages and maintain optimal performance.
Figure 7.2: The ceramic impeller, designed for durability and quiet operation in both fresh and saltwater environments.
8. Nchọpụta nsogbu
| Nsogbu | Ihe nwere ike ime | Ngwọta |
|---|---|---|
| Mgbapụta anaghị ebido | Enweghị ọkụ Onye na-eme ihe ike mechiri emechi Agbanyere nchekwa ọkụ akọrọ | Lelee njikọ ọkụ na ọpụpụ Unplug, disassemble, and clean impeller Ensure pump is fully submerged and water temperature is below 85°C |
| Mbelata mmiri eruba | Clogged inlet or impeller Flow rate knob set too low Ikuku na mgbapụta | Unplug, disassemble, and clean pump components Adjust flow rate knob towards '+' Ensure pump is fully submerged and free of air pockets |
| Oke mkpọtụ ma ọ bụ ịma jijiji | Ihe mgbochi ma ọ bụ mebie ya Pump not stable Na-agba ọsọ akọrọ | Unplug, inspect, and clean impeller. Replace if damaged. Ensure pump is placed on a flat, stable surface Ensure pump is fully submerged in water |
| Mgbapụta na-akwụsị na mberede | Overheating (dry burning protection) Nkwụsị ike | Check water level and temperature. Allow pump to cool before restarting. Lelee ọkọnọ ike |
9. Nkọwapụta
| Njirimara | Nkọwa |
|---|---|
| Nlereanya | AQ009 |
| Ike | 15W |
| Voltage | 110V |
| Ọnụego nfe kacha | 265 GPH (1000 L/H) |
| Kachasị Elu Elu | 4.9 ft |
| Akụkụ ngwaahịa (L x W x H) | 4" x 4" x 4" |
| Ibu Ibu | 0.56 n'arọ (1.23 lbs) |
| Ihe onwunwe | Acrylonitrile Butadiene Styrene (ABS) |
| Outlet Connection (Nozzles) | 1/2" (13mm), 5/8" (16mm) |
| Ogologo eriri ike | 6 ft |
| Ngosi nke enweghị mmiri | IPX8 |
Figure 9.1: Comprehensive table detailing product parameters including power, flow rate, head max, power cord length, outlet connections, and voltage for various pump models. This manual focuses on the 15W model.
10. Akwụkwọ ikike na nkwado
For warranty information or technical support, please refer to the product packaging or contact AQQA customer service directly. Keep your purchase receipt as proof of purchase.
Maka enyemaka ọzọ, ị nwere ike ịga na AQQA Store on Amazon.
