Akwụkwọ ntuziaka+

Sharp B089ZMSR39

Sharp Digital Alarm with AccuSet - Automatic Smart Clock User Manual

Model: B089ZMSR39

Okwu mmalite

This manual provides detailed instructions for the setup, operation, and maintenance of your Sharp Digital Alarm Clock with AccuSet. Designed for ease of use, this clock automatically sets the time, making it ideal for all users.

Sharp Digital Alarm Clock, front view, showing red LED display with time 12:08.

Foto 1: N'ihu view of the Sharp Digital Alarm Clock.

Njirimara ngwaahịa

Diagram showing key features of the Sharp Digital Alarm Clock: Large 0.9 inch Red LED Display, AccuSet Automatic Time Setting, High & Low Display Dimmer Control, Easy Set Top Button Controls, and Installed Battery Backup.

Figure 2: Key features of the Sharp Digital Alarm Clock.

Melite

1. Initial Power-Up and Time Zone Selection

  1. Locate the time zone switch on the bottom of the clock.
  2. Select your desired time zone (e.g., EST for Eastern Standard Time). The default is Eastern Standard Time.
  3. Plug the clock into an approved electrical source. The AccuSet feature will automatically set the correct time.

2. Daylight Savings Time (DST) Adjustment

To adjust for Daylight Savings Time:

3. Ndabere batrị

The clock comes with a pre-installed CR2032 button cell battery. This battery retains time settings during power outages. It is located in a screw-secured compartment at the bottom of the clock.

Ntuziaka ọrụ

N'elu view of the Sharp Digital Alarm Clock showing button labels: DIMMER HI/LO, TIME SET, ALARM SET, SNOOZE, HOUR SET, MINUTE SET, ALARM ON/OFF. Also indicates PM indicator and ALARM indicator on the display.

Figure 3: Top panel controls and display indicators.

1. Ịtọlite ​​mkpu

  1. Pịa AKWARKWỌ NDAR ỌRAR button once. The alarm time will flash on the display.
  2. Pịa Nhazi elekere button to adjust the alarm hour. Observe the PM indicator for correct AM/PM setting.
  3. Pịa Nhazi nkeji bọtịnụ iji dozie nkeji oti mkpu.
  4. Pịa AKWARKWỌ NDAR ỌRAR button again to confirm and exit alarm setting mode.

2. Turning Alarm On/Off

3. Ọrụ snooze

Mgbe oti mkpu na-ada, pịa nnukwu URUA button located on the top of the clock. The alarm will temporarily stop and sound again after approximately 9 minutes.

4. Njikwa Dimmer

Ka ịgbanwee nchapụta nke ihe ngosi LED:

Agara nso view of the Sharp Digital Alarm Clock display, highlighting the high and low dimmer control feature.

Figure 4: Display brightness adjustment.

Nlekọta

Battery Replacement (CR2032)

The pre-installed CR2032 battery is designed to last for several years. If the clock loses time during a power outage, the battery may need replacement.

  1. Unplug the clock from the electrical outlet.
  2. Locate the screw-secured battery compartment on the bottom of the clock.
  3. Unscrew the compartment cover and carefully remove the old CR2032 battery.
  4. Fanye batrị CR2032 ọhụrụ, na-ahụ na polarity ziri ezi (+ akụkụ elu).
  5. Replace the compartment cover and secure it with the screw.
  6. Plug the clock back into the electrical outlet.

Mara: Tụfuo batrị ochie nke ọma dịka iwu obodo siri dị.

Nchọpụta nsogbu

NsogbuIhe nwere ike imeNgwọta
Clock display is blank.Enweghị ike.Ensure the clock is securely plugged into a working electrical outlet. Check the power source.
Oge ezighi ezi.Incorrect time zone selected; DST switch incorrect; Power interruption.Verify the time zone switch on the bottom of the clock. Check the DST switch position. If power was interrupted, the AccuSet should reset the time; if not, check/replace backup battery.
Oti mkpu anaghị ada ụda.Alarm not activated; Incorrect alarm time set.Ensure the alarm indicator light is on (press ALARM ON/OFF button). Verify the alarm time is set correctly.
Ngosipụta na-egbuke egbuke/ nchacha ọkụ.Ntọala Dimmer chọrọ mgbanwe.Press the DIMMER HI/LO button to cycle through brightness settings.

Nkọwapụta

Diagram showing the dimensions of the Sharp Digital Alarm Clock: 5.5 inches wide, 2.6 inches high, and 2.45 inches deep. The display size is 0.9 inches.

Ọgụgụ 5: Akụkụ ngwaahịa.

Ozi Mgbakwunye

For further assistance or product inquiries, please refer to the official Sharp websaịtị ma ọ bụ kpọtụrụ nkwado ndị ahịa ha.

Emebere ngwaahịa a maka naanị ime ụlọ.

Akwụkwọ ndị emetụtara - B089ZMSR39

Tupuview SHARP Atomic Wall Clock: Setup, Features, and Manual
Comprehensive instruction manual for the SHARP Radio Controlled Atomic Wall Clock (Model SPC876), covering setup, time zone settings, DST, signal reception, manual setting, and warranty information.
Tupuview Ntuziaka na Akwụkwọ ikike SPC1019 Elekere Atomic Sharp
Akwụkwọ ntuziaka na akwụkwọ ikike maka Sharp Atomic Clock SPC1019, nhazi zuru ezu, nhazi oge, ọrụ mkpu, na nchọpụta nsogbu.
Tupuview SHARP SPC971 Atomic Wall Clock User Manual and Instructions
Detailed instructions and safety information for the SHARP SPC971 Atomic Wall Clock, covering setup, battery replacement, and operation.
Tupuview Sharp SPC1003/1005 Atomic Weather Station User Manual
Comprehensive guide for the Sharp SPC1003/1005 Atomic Weather Station, detailing features, setup, controls, and specifications for accurate time, weather, and environmental monitoring.
Tupuview Nkọ Atomic Wall Elekere SPC971: Ntuziaka na akwụkwọ ikike
Ozi ntuziaka onye ọrụ na akwụkwọ ikike maka elekere mgbidi Atomic Sharp (Model SPC971), nhazi nkọwa, atụmatụ na akwụkwọ ikike nwere oke otu afọ.
Tupuview Sharp SPC276 Digital Alarm Clock with Bluetooth & Sleep Sounds: User Guide
Comprehensive guide to operating the Sharp SPC276 Digital Alarm Clock, covering features, setup, alarm functions, Bluetooth connectivity, sleep sounds, and safety precautions.