MOXA EDS-305-M-SC-T Industrial Unmanaged Ethernet Switch User Manual

1. Okwu mmalite

This manual provides essential information for the installation, operation, and maintenance of the MOXA EDS-305-M-SC-T Industrial Unmanaged Ethernet Switch. The EDS-305-M-SC-T is designed for industrial applications, offering reliable Ethernet connectivity in harsh environments. It features 4 10/100BaseTX ports and 1 100BaseFX multi-mode SC fiber port, along with a smart relay output for alarm notifications and a wide operating temperature range of -40 to 75°C.

Please read this manual thoroughly before installing or operating the device to ensure proper functionality and safety.

2. Ozi nchekwa

• Always disconnect power before performing any installation or maintenance procedures.
• Ensure proper grounding to prevent electrical hazards and ensure stable operation.
• Do not operate the device in environments exceeding its specified temperature and humidity ratings.
• Use appropriate tools and follow local electrical codes during installation.
• Fiber optic cables should be handled with care. Avoid looking directly into fiber optic ports when the device is powered on.

3. Ngwaahịa gafereview

3.1 Atụmatụ

• 4 10/100BaseTX ọdụ ụgbọ mmiri Ethernet
• 1 100BaseFX multi-mode SC fiber port
• Unmanaged plug-and-play operation
• Smart relay output for alarm events
• Wide operating temperature range: -40 to 75°C
• Ntinye ike DC ugboro abụọ
• DIN-rail mountable design

Ihe ngwugwu 3.2

Chọpụta na ngwungwu gị nwere ihe ndị a:

• MOXA EDS-305-M-SC-T Industrial Unmanaged Ethernet Switch
• Mgbochi njedebe maka ntinye ike na mmepụta relay
• Documentation (Quick Installation Guide, Warranty Card)
• DIN-rail mounting kit (pre-installed or separate)

If any of these items are missing or damaged, please contact your sales representative for assistance.

3.3 Nhazi ngwaọrụ

Figure 1: MOXA EDS-305-M-SC-T Industrial Unmanaged Ethernet Switch. This image shows three industrial switches mounted on a DIN rail, illustrating their compact form factor and typical installation environment.

The EDS-305-M-SC-T features a robust metal casing with various ports and LED indicators on its front panel. Key components include:

• ọdụ ụgbọ mmiri Ethernet: 4 x 10/100BaseTX RJ45 ports for copper cable connections.
• Ọdụ ụgbọ mmiri: 1 x 100BaseFX SC connector for multi-mode fiber optic cable.
• Ihe ngosi LED: Power (PWR), Fault, and Link/Act LEDs for each port.
• Mgbochi ọnụ: For power input (V+, V-, GND) and relay output connections.

4. Nhazi

4.1 Ịtinye mgbanaka

The EDS-305-M-SC-T is designed for DIN-rail mounting. Follow these steps:

1. Hook the top of the DIN-rail clip onto the DIN rail.
2. Press the switch firmly against the DIN rail until the clip snaps into place.
3. Ensure the switch is securely fastened to the DIN rail.

4.2 Wiring the Network Connections

Ethernet Ports (RJ45):

• Connect standard Cat5/5e/6 Ethernet cables from your network devices (e.g., PCs, PLCs, IP cameras) to the RJ45 ports on the switch.
• The switch supports auto MDI/MDI-X, so straight-through or crossover cables can be used.

Fiber Optic Port (SC):

• Connect a multi-mode fiber optic cable with SC connectors to the 100BaseFX port.
• Ensure the transmit (TX) fiber from one device connects to the receive (RX) fiber of the other device, and vice-versa.

4.3 Njikọ ike

The EDS-305-M-SC-T supports redundant dual DC power inputs. Use the provided terminal block for power connections.

1. Gbaa mbọ hụ na isi iyi ike dị n'ime voltage range (e.g., 12-48 VDC).
2. Connect the positive wire to the V+ terminal, the negative wire to the V- terminal, and the ground wire to the GND terminal on the terminal block.
3. Insert the wired terminal block into the power input slot on the switch.
4. Apply power to the switch. The PWR LED should illuminate.

4.4 Njikọ Mmepụta Relay

The smart relay output can be connected to an external alarm device (e.g., a buzzer or light) to signal network events or power failures.

1. Connect the alarm device to the relay output terminals on the terminal block.
2. Refer to the device's specific wiring diagram for correct polarity and connection.

5. .rụ ọrụ

5.1 Basic Arụmọrụ

The EDS-305-M-SC-T is an unmanaged switch, meaning it operates as plug-and-play. Once powered on and connected to network devices, it automatically forwards Ethernet frames between connected ports. No software configuration is required for basic network operation.

5.2 LED egosi

Monitor the LED indicators on the front panel to check the switch's status and network activity:

• PWR LED: Illuminates green when power is supplied to the switch.
• Ikanam ezighi ezi: Illuminates red when a power input failure occurs.
• Link/Act LEDs (RJ45 Ports):
  • Green (Solid): Indicates a valid network link.
  • Green (Flashing): Indicates network activity (data transmission/reception).
• Link/Act LED (Fiber Port):
  • Green (Solid): Indicates a valid fiber optic link.
  • Green (Flashing): Indicates fiber optic network activity.

6. Nlekọta

6.1 Nhicha

Periodically clean the exterior of the switch with a soft, dry cloth. Do not use liquid or aerosol cleaners. Ensure the device is powered off before cleaning.

6.2 Nyochaa njikọ

Regularly inspect all cable connections (Ethernet, fiber, power, relay) to ensure they are secure and free from damage. Loose or damaged connections can lead to intermittent network issues or device malfunction.

7. Nchọpụta nsogbu

If you encounter issues with your EDS-305-M-SC-T switch, refer to the following troubleshooting tips:

• Enweghị ike: Check the power supply connection and ensure the power source is active. Verify the PWR LED is illuminated.
• No Link on Ethernet Port: Ensure the Ethernet cable is securely connected at both ends. Check the cable for damage. Verify the connected device is powered on and functioning correctly.
• No Link on Fiber Port: Ensure the fiber optic cable is securely connected and not damaged. Verify the TX/RX polarity is correct. Check the connected fiber device for proper operation.
• Okwu Njikọta netwọkụ: If multiple devices are affected, check the upstream network devices. Ensure there are no IP address conflicts if static IPs are used on connected devices.
• FAULT LED is ON: This indicates a power input failure. Check the power connections and the power supply unit.

If problems persist after attempting these steps, please contact MOXA technical support for further assistance.

8. Nkọwapụta

9. Akwụkwọ ikike na nkwado

MOXA products are backed by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official MOXA websaịtị.

For technical support, product inquiries, or service requests, please contact MOXA customer support through their official website or the contact information provided in your product documentation. When contacting support, please have your product model (EDS-305-M-SC-T) and serial number ready.

MOXA Official Websaịtị: www.madue.com