Okwu mmalite
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Emerson 1E78-140 Non-Programmable Heat Only Thermostat. Please read this manual thoroughly before installation and use to ensure proper function and safety.
The Emerson 1E78-140 is designed for use with most single-stage heat-only systems, including 24-volt and millivolt systems. It is not compatible with electric baseboard heat or certain other systems.
Ntọala na nwụnye
Ngwa achọrọ
- Screwdriver
- Gwuo olulu (ọ bụrụ na ọ dị mkpa ka e tinye oghere ọhụrụ)
- Wire strippers (ọ bụrụ na achọrọ)
Wepụ Thermostat ochie gị
- Turn off power to your heating system at the main fuse or circuit breaker panel.
- Wepu mkpuchi nke igwe ikuku ochie gị.
- Take a photo of the existing wiring connections for reference.
- Disconnect the wires from the old thermostat terminals, noting which wire was connected to each terminal.
- Remove the old thermostat base from the wall.
Ịkwanye Thermostat Ọhụrụ
- Kewapụ mkpuchi ihu na ntọala thermostat.
- Position the new thermostat base on the wall. Use the provided screws and anchors to secure it.
Wiring
Ihe dị mkpa: Ensure power is off before wiring. This thermostat is for 2-wire heat-only systems. Connect wires only to R and W terminals.
Refer to the wiring diagram below. Identify each wire attached to the old thermostat by taking a photo of old wiring.
Image: Wiring diagram for the Emerson 1E78-140 thermostat. It illustrates connections for 2-wire heat-only systems to R and W terminals. The image also shows two AAA Energizer batteries and various mounting screws and anchors included with the thermostat. A caution notice regarding battery life and freeze hazard is visible.
- Connect the wire from your heating system's R terminal to the R terminal on the thermostat.
- Connect the wire from your heating system's W terminal to the W terminal on the thermostat.
Ntinye batrị
The thermostat requires two AAA batteries for operation. Install the batteries into the compartment located on the back of the thermostat, observing the correct polarity (+/-).
Foto: N'ihu view of the Emerson 1E78-140 thermostat. The digital display shows "70" as the current temperature. To the right of the display are two gray buttons for adjusting the temperature up and down. Below the Emerson logo, a system switch is visible, set to "OFF HEAT".
After wiring and battery installation, attach the thermostat front cover to the base.
Turn on power to your heating system at the main fuse or circuit breaker panel.
Ntuziaka ọrụ
Sistem Gbanye
The system switch is located on the front of the thermostat. It has two positions:
- Gbanyụọ: Turns the heating system off.
- Ọkụ: Activates the heating system to maintain the set temperature.
Ịtọlite okpomọkụ
Use the Up (▲) and Down (▼) buttons located next to the digital display to adjust your desired temperature setting. The thermostat will maintain this temperature with a precision of plus/minus 1 degree Fahrenheit.
Ìhè azụ
The digital display features a backlight for improved visibility, especially in low-light conditions. The backlight activates when buttons are pressed.
Nlekọta
Ngbanwe batrị
When the "Change Battery" indicator (a battery icon) is displayed on the screen, the batteries have limited remaining life and should be replaced soon. The system will not operate with dead batteries.
- Wepu mkpuchi okpomọkụ.
- Wepụ batrị AAA ochie.
- Insert two new AAA alkaline batteries, ensuring correct polarity.
- Dochie mkpuchi okpomọkụ.
Nhicha
Jiri nwayọ hichaa igwe ọkụ, damp akwa . Ejila ihe nchacha abrasive ma ọ bụ ihe mgbaze.
Nchọpụta nsogbu
| Nsogbu | Ihe nwere ike ime | Ngwọta |
|---|---|---|
| Ngosipụta bụ oghere ma ọ bụ nchara nchara. | Batrị nwụrụ anwụ ma ọ bụ dị ala. | Dochie batrị AAA abụọ ahụ. |
| Usoro ikpo ọkụ anaghị agbanye. |
|
|
| "Change Battery" icon displayed. | Ike batrị dị ala. | Replace the two AAA batteries promptly. |
Nkọwapụta
| Njirimara | Nkọwa |
|---|---|
| Ụdị | Emerson |
| Nọmba nlereanya | 1E78-140 |
| Ụdị njikwa | Pịa bọtịnụ |
| Njirimara Pụrụ Iche | Ngosipụta okpomọkụ |
| Ụdị njikwa okpomọkụ | Akwụkwọ ntuziaka |
| Ngwa gụnyere | Thermostat, Temperature Sensor |
| Isi Iyi Ike | Electric (2 AAA batteries for display/control) |
| Voltage | 24 Volts (for system operation) |
| Ụdị ngosi | Ikanam |
| Usoro njikwa | Metụ aka (bọtịnụ) |
| Ụdị nkwụnye | Ugwu mgbidi |
| Ụdị | Dijitalụ |
| Ìhè azụ | Ee |
| Ndakọrịta | Ọtụtụ otu-stage heat-only systems (24V and millivolt). Not compatible with electric baseboard heat. |
| Nkenkenke | +/- 1 degree F |
Foto: Akụkụ view of the Emerson 1E78-140 thermostat, held in a hand for scale. The image indicates the thermostat's height is 5.5 inches (14 cm).
Ozi akwụkwọ ikike
Specific warranty details for the Emerson 1E78-140 thermostat are typically provided with the product packaging or can be obtained directly from the manufacturer, Emerson. Please refer to the documentation included in your product box or visit the official Emerson websaịtị maka usoro na ọnọdụ akwụkwọ ikike kachasị ọhụrụ.
Nkwado ndị ahịa
For technical assistance, troubleshooting beyond this manual, or inquiries regarding your Emerson 1E78-140 thermostat, please contact Emerson customer support. Contact information can usually be found on the product packaging or on the official Emerson websaịtị.
