Okwu mmalite
Thank you for choosing the Sunco LED Wraparound Shop Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before installation and retain them for future reference.
Ozi nchekwa
- Ịdọ aka ná ntị: Ihe ize ndụ nke ujo eletrik. Kwupu ike na fiusi ma ọ bụ sekit breaker tupu echichi ma ọ bụ ọrụ.
- A ga-etinyerịrị ngwaahịa a dịka koodu nrụnye ọdabara si dị site n'aka onye maara ihe nrụpụta na arụmọrụ nke ngwaahịa na ihe egwu dị.
- Gbaa mbọ hụ na ọkọnọ voltage is compatible with the fixture (120-277V).
- Do not handle live wires.
- Do not modify the fixture. Any modifications may void the warranty and create safety hazards.
- Kwesịrị ekwesị maka damp ebe.
Ihe ngwugwu
Chọpụta na akụrụngwa niile dị tupu ịmalite nrụnye:
- LED Wraparound Shop Light Fixture (2 units for 2-pack)
- Ngwaike mgbakwasa
- Linking Cables (for connecting multiple fixtures)
- Akwụkwọ ntuziaka
Nkọwapụta
| Nọmba nlereanya | SHW-40W-5K-2PK |
| Oriri ike | 40 Watt |
| Mmepụta ọkụ | 3500 Lumen |
| Okpomọkụ agba | 5000K Ìhè ụbọchị |
| Voltage | 120-277V |
| Akụkụ | 48"L x 5.35"W x 2.36"H |
| Angle Beam | 110-ogo |
| CRI | 80+ |
| Ụdị nwụnye | Flush Mount / Hardwired |
| Atụmatụ pụrụ iche | Prismatic Lens, Linkable (up to 8 units), Non-Dimmable |
| Asambodo | ETL |
Ntuziaka nwụnye
This fixture is designed for direct surface mounting to the ceiling. Always ensure power is disconnected before starting installation.
- Kwadebe Ihe Ndozi: Carefully remove the diffuser (Part B) from the lamp base (Part A) to access the wiring and mounting points.
- Ugwu ihe ndozi ahụ: Debe lamp base against the ceiling where you intend to install it. Mark the mounting holes. Use appropriate mounting hardware (screws, anchors) to securely attach the lamp base to the ceiling.
- Wiring: Bring the electrical supply wires from the junction box to the fixture. Connect the wires according to local electrical codes: Black to Black (Live), White to White (Neutral), Green/Bare Copper to Green (Ground). Ensure all connections are secure with wire nuts.
- Replace Diffuser: Once wiring is complete and secure, carefully reattach the diffuser to the lamp base. Ensure it snaps firmly into place along both sides.
Linking Multiple Fixtures
These fixtures are linkable, allowing you to connect up to 8 units from a single power source. Use the provided linking cables or flush linking connectors to connect fixtures end-to-end. Ensure the total wattage nke ihe eji ejikọta anaghị agafe ikike sekit ahụ.
Ọrụ
Once properly installed and powered, the Sunco LED Wraparound Shop Light will provide instant-on, flicker-free illumination. This fixture is non-dimmable and operates at a 5000K Daylight color temperature, designed to mimic natural daylight for enhanced visibility and alertness.
Nlekọta
The Sunco LED Wraparound Shop Light is designed for long-lasting performance with minimal maintenance. The integrated LED design means there are no bulbs to replace.
- Nhicha: Ensure power is off before cleaning. Wipe the fixture and diffuser with a soft, damp Ákwà. Ejila ihe nhicha ma ọ bụ ihe mgbaze, n'ihi na ihe ndị a nwere ike imebi ihe ndị dị n'ime ya ma ọ bụ ihe ndị dị n'ime ya.
- Nyocha: Periodically inspect the fixture for any signs of damage or loose connections. If any issues are found, disconnect power and contact a qualified electrician or Sunco Lighting support.
Nchọpụta nsogbu
If you experience issues with your Sunco LED Wraparound Shop Light, refer to the following common problems and solutions:
| Nsogbu | Ihe nwere ike ime | Ngwọta |
|---|---|---|
| Ìhè anaghị agbanwuo | No power supply; Loose wiring; Faulty fixture. | Check circuit breaker/fuse. Ensure all wire connections are secure. If problem persists, contact Sunco support. |
| Ìhè na-ada ada ma ọ bụ na-egbuke egbuke | Incompatible dimmer switch (fixture is non-dimmable); Loose wiring; Power fluctuation; Fixture nearing end of life. | Ensure no dimmer switch is used. Check wiring connections. If dimming occurs after extended use (e.g., 1.5-2 years), it may indicate a component issue. Contact Sunco support for warranty assistance. |
| Only some linked lights are working | Loose linking cable connection; Faulty individual fixture in the chain. | Check all linking cable connections. Isolate the non-working fixture to determine if it's an individual unit issue. |
If troubleshooting steps do not resolve the issue, please contact Sunco Lighting customer support.
Akwụkwọ ikike na nkwado
Sunco Lighting stands behind the quality of its products. This LED Wraparound Shop Light comes with a Nchekwa afọ 7 warranty. For warranty claims, technical assistance, or any questions regarding your product, please contact our knowledgeable support specialists.
Ozi mkpọtụrụ: Please refer to the Sunco Lighting websaịtị ma ọ bụ akwụkwọ ịzụrụ ihe maka nkọwa kọntaktị kachasị ugbu a.
