Wisi Orbit Line OA10A Offset Satellite Antenna User Manual

1. Okwu mmalite

1.1 Nnọọ

Thank you for choosing the Wisi Orbit Line OA10A Offset Satellite Antenna. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your satellite antenna. Please read this manual thoroughly before beginning installation and retain it for future reference.

1.2 Ntuziaka nchekwa

Debe ihe nchekwa nchekwa ndị a iji gbochie mmerụ ahụ na mmebi akụrụngwa:

• Ekwesịrị ịrụ ya naanị ndị ọrụ ruru eru.
• Always disconnect power to any associated equipment before installation or maintenance.
• Avoid contact with power lines during installation.
• Use appropriate safety gear, including gloves, safety glasses, and a harness when working at heights.
• Ensure the mounting structure is stable and capable of supporting the antenna's weight and wind load.
• Do not attempt to modify the antenna or its components.

2. Ihe ngwugwu

2.1 Ihe dị n'ime ya

Chọpụta na akụrụngwa niile dị na ngwugwu:

• 1x Wisi Orbit Line OA10A Offset Satellite Reflector (100 cm)
• 1x LNB Support Arm
• 1x LNB Holder (40 mm)
• 1x Mast Clamp Tọọ
• 1x Mounting Hardware Kit (screws, nuts, washers)

Foto 1: N'ihu view of the Wisi Orbit Line OA10A satellite antenna, showing the reflector dish and the LNB arm.

3. Ntọala na nwụnye

3.1 Nhọrọ saịtị

Choose an installation location that provides a clear line of sight to the desired satellite(s). Avoid obstructions such as trees, buildings, or other structures. The mounting surface or mast must be robust enough to withstand wind loads and the weight of the antenna.

3.2 Ntuziaka Mgbakọ

Follow these steps to assemble the satellite antenna:

1. Attach the LNB support arm to the back of the reflector dish using the provided screws and nuts. Ensure it is securely fastened.
2. Slide the 40 mm LNB holder onto the end of the LNB support arm. Do not tighten completely yet, as adjustment may be needed.
3. Secure the mast clamp set to the antenna's mounting bracket.

Foto 2: N'azụ view of the Wisi Orbit Line OA10A satellite antenna, illustrating the mounting bracket and mast clamp mgbakọ.

3.3 Ịwụnye Antenna ahụ

Mount the assembled antenna to a sturdy mast or wall bracket. Use the mast clamp set to firmly secure the antenna. Ensure the mast is plumb and the antenna is level before making final adjustments. Do not overtighten the clamps initially, as fine adjustments will be required for satellite alignment.

3.4 LNB Installation

Insert your LNB (Low Noise Block converter) into the 40 mm LNB holder. Ensure the LNB is correctly oriented according to your satellite provider's specifications, typically with the F-connector pointing downwards to prevent water ingress. Secure the LNB in place with the provided clamp or screw on the LNB holder.

4. Operating the Satellite Antenna

4.1 Alignment and Signal Acquisition

Accurate alignment is crucial for optimal signal reception. This process typically involves adjusting the antenna's azimuth (horizontal angle) and elevation (vertical angle), and the LNB skew (rotation). A satellite finder meter is highly recommended for this step.

1. Consult your satellite provider or online resources for the correct azimuth, elevation, and LNB skew settings for your specific location and desired satellite.
2. Connect the satellite finder meter between the LNB and your satellite receiver.
3. Slowly adjust the antenna's elevation and azimuth, making small movements until the satellite finder indicates a strong signal.
4. Fine-tune the LNB skew for maximum signal quality.
5. Once the optimal signal is achieved, carefully tighten all mounting bolts and LNB holder screws to prevent movement.

4.2 Connecting to Receiver

Connect the coaxial cable from the LNB to the 'Satellite In' port on your satellite receiver. Ensure all connections are secure and weatherproofed if exposed to the elements.

5. Nlekọta

5.1 Nlekọta n'ozuzu

The Wisi Orbit Line OA10A antenna is designed for durability. Regular maintenance will ensure long-term performance:

• Periodically inspect the antenna for any physical damage, loose bolts, or corrosion.
• Clean the reflector surface with a soft cloth and mild detergent if dirt or debris accumulates, as this can degrade signal quality. Rinse thoroughly with water.
• Check coaxial cable connections for signs of wear or water ingress. Replace damaged cables or connectors.

5.2 Weather Considerations

In areas prone to heavy snow or ice, periodically clear the reflector surface to prevent signal loss and structural strain. During severe storms, consider temporarily lowering or securing the antenna if possible, though the design is robust for typical weather conditions.

6. Nchọpụta nsogbu

6.1 Okwu nkịtị na Ngwọta

7. Nkọwapụta

7.1 Data teknụzụ

• Ụdị: OA10A (75675)
• Nha Ngosipụta: 100 cm
• LNB Holder Diameter: 40 mm
• Mgbochi: 50 ohms
• Agba: Ìhè isi awọ
• Ọnụọgụ ọwa: 1 (referring to LNB input)
• ASIN: B07C2NDPK2
• EAN: 04010056756758

8. Akwụkwọ ikike na nkwado

8.1 Ozi akwụkwọ ikike

Wisi products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or contact your retailer. Keep your proof of purchase for warranty claims.

8.2 Nkwado ndị ahịa

If you encounter issues not covered in this manual or require further assistance, please contact your Wisi dealer or the customer support channel provided by your point of purchase. When contacting support, please have your model number (OA10A or 75675) and purchase details ready.