Altec Lansing ALT-500 Classic Turn Bluetooth Turntable User Manual

Okwu mmalite

This manual provides essential instructions for the setup, operation, and maintenance of your Altec Lansing ALT-500 Classic Turn Bluetooth Turntable. Please read this guide thoroughly before using the product to ensure proper function and longevity.

Ihe ngwugwu

• Altec Lansing ALT-500 Turntable Unit
• Ihe mkpuchi uzuzu
• Stylus Cartridge (pre-installed)
• DC 12V ihe nkwụnye ọkụ
• 45 RPM nkwụnye
• Akwụkwọ ntuziaka onye ọrụ

Melite

1. Mwepu na ntinye

Carefully remove all components from the packaging. Place the turntable on a stable, level surface away from direct sunlight, heat sources, and excessive dust or vibrations. Ensure adequate ventilation around the unit.

2. Dust Cover Installation

Align the hinges of the dust cover with the hinge mounts on the rear of the turntable unit. Gently push down until the cover is securely in place. The dust cover protects the platter and stylus when not in use.

Image: The ALT-500 turntable with its clear protective dust cover in the open position, ready for use.

3. Stylus Protection Removal

Before first use, carefully remove the clear plastic stylus protector from the cartridge. Handle the tonearm gently to avoid damaging the stylus.

4. Njikọ ike

Connect the DC 12V power adapter to the 'DC IN' jack on the rear of the turntable. Plug the adapter into a standard wall outlet. The power indicator light will illuminate when connected.

Image: Rear panel of the ALT-500 turntable, highlighting the DC 12V power input and L/R RCA audio output jacks.

Na-arụ ọrụ na Turntable

1. Ịgbanye / gbanyụọ

Locate the power switch, typically on the rear or side of the unit. Flip it to the 'ON' position to power on the turntable. Flip to 'OFF' when not in use.

2. Ịkpọ ndekọ

1. Place a record on the platter. If playing a 45 RPM single, place the 45 RPM adapter over the spindle first.
2. Jiri ihe mgbanwe nhọrọ ọsọ họrọ ọsọ kwesịrị ekwesị (33, 45, ma ọ bụ 78 RPM).
3. Unlock the tonearm clip.
4. Lift the cueing lever to raise the tonearm.
5. Manually position the tonearm over the desired starting groove of the record.
6. Gently lower the cueing lever to allow the stylus to descend onto the record. The platter will begin to spin automatically.
7. Adjust the volume using the volume knob on the unit.

Foto: nkọwa zuru ezu view of the ALT-500 turntable's platter, tonearm rest, and speed/auto-stop selector switches.

Image: A close-up shot of the turntable's stylus cartridge resting on the grooves of a vinyl record.

3. Auto-Stop Feature

The ALT-500 features an auto-stop function that automatically stops the platter from spinning once the record has finished playing. This feature can typically be toggled ON/OFF via a switch near the platter.

4. Kwụsị playback

To stop playback, lift the cueing lever to raise the tonearm, then manually return the tonearm to its rest and secure it with the clip. Turn off the unit when finished.

Njikọ Bluetooth

1. Connecting to an External Bluetooth Speaker

The ALT-500 can transmit audio wirelessly to an external Bluetooth speaker or headphones.

1. Ensure your external Bluetooth device is in pairing mode.
2. Activate the Bluetooth function on the ALT-500 (refer to the unit's controls for the Bluetooth pairing button/switch). The Bluetooth indicator will flash.
3. The turntable will search for and connect to the nearest available Bluetooth device. Once connected, the indicator will become solid.
4. Audio from the record will now play through your external Bluetooth speaker.

2. Streaming Music to the Turntable (Bluetooth Input)

You can also stream music from your smartphone or other Bluetooth-enabled device to the ALT-500's built-in speakers.

1. Ensure the turntable is powered on and in Bluetooth receiving mode (the Bluetooth indicator may flash or be solid, depending on the mode).
2. On your smartphone or device, go to Bluetooth settings and search for 'ALT-500' or a similar name.
3. Select the turntable to pair. Once connected, you can play audio from your device through the turntable's speakers.

External Audio Connections

The ALT-500 is equipped with L/R RCA output jacks on the rear panel, allowing you to connect the turntable to an external amplifier or home stereo system for enhanced sound.

• Connect an RCA cable (not included) from the 'OUT' jacks on the turntable to the 'AUX IN' or 'LINE IN' inputs on your amplifier ma ọ bụ nnata.
• Ihe dị mkpa: Do not connect to a 'PHONO IN' input, as this turntable has a built-in pre-amplifier and connecting to a phono input could result in distorted sound.

Image: Rear panel of the ALT-500 turntable, showing the DC 12V power input and the L/R RCA audio output jacks for connecting to external audio systems.

Nlekọta

1. Cleaning the Stylus

A clean stylus ensures optimal sound quality and extends the life of your records. Use a soft brush designed for stylus cleaning, brushing gently from back to front. Avoid touching the stylus with your fingers.

2. Ichacha Unit

Wipe the turntable's exterior with a soft, dry, lint-free cloth. Do not use abrasive cleaners, waxes, or solvents. Ensure the unit is powered off and unplugged before cleaning.

3. Dust Cover Care

Clean the dust cover with a soft, damp cloth. Avoid using harsh chemicals that could scratch or cloud the plastic.

Nchọpụta nsogbu

Nkọwapụta

• Nọmba nlereanya: ALT-500
• Akụkụ ngwaahịa: 12.95 x 12.32 x 4.41 sentimita asatọ
• Ibu ihe: 7.27 pound
• Akara: Altec Lansing
• Ihe: Plastic
• Agba: Ọcha
• Ngwa dakọtara: Smartphone, Speaker, Tablet
• Ụdị moto: moto AC
• Isi mmalite ike: Ọkụ eletriki ejiri eriri (DC 12V)
• Ọsọ ọsọ: 33 1/3, 45, 78 RPM
• Njikọta: Bluetooth, L/R RCA Output
• Atụmatụ: Built-in Stereo Speakers, Dust Cover, Auto Stop

Akwụkwọ ikike na nkwado

For warranty information and technical support, please refer to the documentation included with your purchase or visit the official Altec Lansing websaịtị. Debe ihe akaebe nke ịzụrụ maka akwụkwọ ikike.