Ntuziaka Ntuziaka Kia Mobility KIT-TAIRE (Model 52933-2Y000)

Okwu mmalite

This manual provides essential instructions for the safe and effective operation, maintenance, and troubleshooting of your Kia Mobility KIT-TIRE (Model 52933-2Y000) tire compressor. Please read this manual thoroughly before using the product and retain it for future reference. Always refer to your vehicle's owner's manual for specific tire pressure recommendations and emergency procedures.

Ozi nchekwa dị mkpa

• Do not use for sidewall punctures: This device is designed for temporary repair of tread punctures only. It is not suitable for punctures on the tire sidewall or for significant tire damage.
• Zere ikpo oke ọkụ: Continuous operation can cause the compressor to overheat. Allow the unit to cool down if it becomes excessively hot during use.
• Kwesịrị ekwesị voltage: Ensure the compressor is connected to a 12-volt DC power source, typically your vehicle's accessory outlet.
• Ụmụaka na anụ ụlọ: Keep the compressor and its components away from children and pets.
• Nchedo anya: Wear appropriate eye protection when operating the compressor.
• Vehicle stability: Ensure your vehicle is parked on a level surface with the parking brake engaged before attempting any tire inflation.
• Nrụgide taya: Always inflate tires to the pressure specified in your vehicle's owner's manual or on the tire placard. Over-inflation can be dangerous.

For detailed visual instructions, refer to the diagram below:

Foto 1: N'ihu view of the Kia Mobility KIT-TIRE compressor, illustrating connection points, power switch, and operational steps.

Melite

1. Prepare the vehicle: Park your vehicle on a flat, stable surface. Engage the parking brake and turn off the engine.
2. Locate the compressor: Remove the Kia Mobility KIT-TIRE compressor from its storage location.
3. Connect to tire valve: Unscrew the valve cap from the tire. Firmly screw the compressor's air hose connector onto the tire valve stem until secure.
4. Jikọọ na ike: Insert the compressor's power plug into your vehicle's 12V accessory outlet (cigarette lighter socket). Ensure the vehicle's ignition is in the "ACC" or "ON" position, or the engine is running, as required by your vehicle.

Ntuziaka ọrụ

1. Nlele Nrụgide Mbụ: Before turning on the compressor, observe the current tire pressure reading on the integrated gauge.
2. Malite onu oriri: Flip the power switch on the compressor to the "ON" position. The compressor will begin to inflate the tire.
3. Nyochaa Nrụgide: Continuously monitor the pressure gauge. Inflate the tire to the recommended pressure (e.g., 2.0-2.8 bar / 30-40 psi, or as specified in your vehicle's manual).
4. Kwụsị ọnụ ahịa: Once the desired pressure is reached, immediately switch the compressor to the "OFF" position.
5. Kwụpụ: Unscrew the air hose connector from the tire valve and replace the valve cap. Disconnect the power plug from the vehicle's 12V outlet.
6. Post-Inflation Driving (for temporary sealant use): If using the compressor with tire sealant for a temporary repair, drive the vehicle immediately for a short distance (e.g., 10 km / 6 miles) at a moderate speed (e.g., 20-80 km/h or 15-50 mph) to allow the sealant to distribute evenly.
7. Re-check Pressure: After driving, re-check the tire pressure. If the pressure has dropped significantly, the repair may not be effective, and professional assistance is required.

Nlekọta

• Nhicha: Wipe the exterior of the compressor with a damp akwa . Ejila kemịkalụ siri ike ma ọ bụ tinye akụkụ ahụ n'ime mmiri.
• Nchekwa: Store the compressor in a cool, dry place, away from direct sunlight and extreme temperatures. Ensure the hose and power cord are neatly coiled to prevent damage.
• Nyocha: Periodically inspect the air hose, power cord, and connectors for any signs of wear, cracks, or damage. Do not use the unit if any components are damaged.

Nchọpụta nsogbu

• Compressor does not turn on:
  • Ensure the power plug is fully inserted into the 12V outlet.
  • Check the vehicle's 12V outlet fuse.
  • Verify the vehicle's ignition is in the correct position (ACC or ON).
• Slow inflation or no inflation:
  • Ensure the air hose connector is securely attached to the tire valve.
  • Check for leaks in the air hose or connections.
  • Verify the tire valve stem is not damaged.
  • If the tire has a large puncture or sidewall damage, the compressor may not be able to inflate it.
• Compressor overheats:
  • Allow the unit to cool down for at least 10-15 minutes before resuming operation.
  • Avoid continuous operation for extended periods.
• Ọgụgụ nrụgide na-ezighi ezi:
  • Ensure the compressor is on a stable surface.
  • Compare the reading with a known accurate tire pressure gauge if available.

Nkọwapụta

For additional technical details, refer to the product label shown below:

Foto nke atọ: Azụ view of the Kia Mobility KIT-TIRE compressor, showing model, power, and manufacturing details.

Ozi akwụkwọ ikike

Specific warranty details for the Kia Mobility KIT-TIRE (Model 52933-2Y000) are not provided in this manual. Please refer to the warranty documentation included with your purchase or contact your authorized Kia dealer or the product seller for comprehensive warranty information.

Nkwado ndị ahịa

For technical assistance, service, or inquiries regarding your Kia Mobility KIT-TIRE, please contact your authorized Kia service center or the retailer from whom you purchased the product. Provide your model number (52933-2Y000) when seeking support to ensure accurate assistance.