1. Okwu mmalite
This manual provides detailed instructions for the installation, operation, and maintenance of the MEAN WELL ELG-75-C700 Single Output Switching LED Power Supply. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Image 1.1: The MEAN WELL ELG-75-C700 LED Power Supply, showing its compact metal casing and wiring connections.
2. Features and Applications
The ELG-75-C series is a 75W AC/DC LED driver featuring constant current mode and high output voltage. It operates from 180-295VAC and offers various models with different rated current ranges. Key features include:
- Constant current output with high output voltage (>60VDC).
- Universal AC input range: 180~295VAC only.
- Built-in active Power Factor Correction (PFC) function.
- High efficiency up to 93%.
- Ịjụ oyi site na ikuku ikuku efu.
- Protections: Short circuit, Over voltage, Over temperature.
- Output current adjustable via output cable or internal potentiometer (depending on model type).
- IP67 / IP65 design for indoor or outdoor installations.
- Kwesịrị ekwesị maka nkụ, damp, ma ọ bụ ebe mmiri.
- Suitable for LED lighting and street lighting applications.
- Meets 6KV surge immunity level (IEC61000-4-5).
- No load power consumption <0.5W.
- Type HL LED Driver for use in Class I, Division 2 hazardous location luminaires.
Typical applications for this power supply include LED street lighting, LED bay lighting, LED greenhouse lighting, and other Class I, Division 2 hazardous location luminaires.
Foto 2.1: Ofeview of the ELG-75-C series features and typical applications, including LED street lighting and greenhouse lighting. This image also contains the model encoding information.
3. Model Encoding
The model number provides information about the specific configuration of the power supply:
ELG - 75 - CXXX [A/B/D/DA]
- ELG: Series Name
- 75: Output wattage (75W)
- CXXX: Constant Current Output (e.g., C700 for 700mA)
- Ụdị oghere: IP67 rated. Cable for I/O connection.
- A-Ụdị: IP65 rated. Constant current level adjustable through internal potentiometer.
- Ụdị B-Ụdị: IP67 rated. Built-in 3-in-1 dimming function (0~10VDC, PWM signal, or resistance).
- D-Type (option): IP67 rated. Smart Timing Dimming function.
- DA-Type (option): IP67 rated. DALI function.
Refer to Image 2.1 for a visual representation of the model encoding structure.
4. Nkọwapụta
Detailed electrical and environmental specifications for the ELG-75-C series are provided below. Note that the ELG-75-C700 is specifically rated for 700mA output.
| Oke | ELG-75-C350 | ELG-75-C500 | ELG-75-C700 | ELG-75-C1050 | ELG-75-C1400 |
|---|---|---|---|---|---|
| Mpụta | |||||
| Enyere aha ugbu a | 350mA | 500mA | 700mA | 1050mA | 1400mA |
| Mpaghara na-adị ugbu a mgbe niile | 107-214V | 75-150V | 53-107V | 35-71V | 27-54V |
| Enyere ike | 74.9W | 75W | 74.9W | 74.55W | 75.6W |
| Ripple & mkpọtụ (kacha) | 2Vp-p | 1.5Vp-p | 1.0Vp-p | 1.0Vp-p | 0.5Vp-p |
| Nkwenye ugbu a | ±5.0% | ||||
| Adj. Oke | Can be adjusted by internal potentiometer (for A-Type only) | ||||
| 175-350mA | 250-500mA | 350-700mA | 525-1050mA | 700-1400mA | |
| Enweghi Mmepụta Voltage (max.) | 224V | 158V | 114V | 78V | 61V |
| Mbido, Bilie Oge | 500ms, 100ms na ibu zuru oke | ||||
| Jidesie Oge | 10ms na ibu zuru oke | ||||
| Ntinye | |||||
| Voltage Oke | 180-295VAC | ||||
| Oke ugboro ugboro | 47 ~ 63Hz | ||||
| Power Factor (typ.) | PF> 0.95/230VAC, PF> 0.92/277VAC na ibu zuru oke | ||||
| Mgbagwoju anya Harmonic Distor | THD < 20% when output loading ≥50% at 230VAC input and output loading ≥75% at 277VAC input | ||||
| Ịrụ ọrụ (ụdị) | 91% | 91% | 90% | 90% | 90% |
| AC ugbu a (ụdị) | 0.45A/230VAC | 0.38A/277VAC | |||
| Inrush Ugbu a (ụdị.) | COLD START 50A (twidth=350µs measured at 50% Ipeak) at 230VAC | ||||
| Oke. Nọmba nke PSU na 16A sekit Breaker | Nkeji 5 (onye na-emebi okirikiri nke ụdị B) / nkeji 8 (onye na-emebi okirikiri nke ụdị C) na 230VAC | ||||
| Nchedo | |||||
| Nhapu ugbu a | <0.75mA / 277VAC | ||||
| Obere sekit | Ọnọdụ mgbakasị ahụ, na-agbake na-akpaghị aka ka ewepụrụ ọnọdụ mmejọ | ||||
| N'ime Voltage | 225-260V | 160-190V | 115-140V | 80-100V | 64-79V |
| Ụdị Nchedo | Mechie O/P voltage, re-ike na mgbake | ||||
| N'elu okpomọkụ | Mechie O/P voltage, re-ike na mgbake | ||||
| Gburugburu Ebe Obibi | |||||
| Okpomọkụ na-arụ ọrụ. | Tcase = -40 ~ +85°C (Refer to "Derating Curve") | ||||
| Oke. Ọnọdụ okpomọkụ. | Tcase = +85°C | ||||
| Iru mmiri na-arụ ọrụ | 20 ~ 95% RH na-abụghị condensing | ||||
| Okpomọkụ nchekwa, iru mmiri | -40~+80°C, 10~95% RH | ||||
| Okpomọkụ Ọnụọgụ | ±0.03%/°C (0~50°C) | ||||
| Mmaji | 10~500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes | ||||
| Nchekwa & EMC | |||||
| Ụkpụrụ nchekwa | UL8750(Type HL), EN61347-1, EN61347-2-13 independent, EN62384, IP65 or IP67 approved | ||||
| Nagide Voltage | I/P-O/P:3.75KVAC, I/P-FG:2.0KVAC, O/P-FG:1.5KVAC | ||||
| Nguzogide iche | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C / 70% RH | ||||
| Mgbanwe EMC | Compliance to EN55015,EN61000-3-2 Class C (≥ 50% load); EN61000-3-3 | ||||
| Mgbochi EMC | Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level (surge 6KV) | ||||
| Ndị ọzọ | |||||
| MTBF | 305Khrs min. MIL-HDBK-217F (25°C) | ||||
| Akụkụ | 180*63*35.5 mm (L*W*H) | ||||
| Nkwakọ ngwaahịa | 0.7Kg; 16pcs / 12.6Kg / 0.67CUFT | ||||
Image 4.1: Detailed specifications table for the ELG-75-C series, including output, input, protection, environment, safety, EMC, and other parameters.
5. Ntọala na nwụnye
Proper installation is crucial for the safe and reliable operation of the LED power supply. Refer to the mechanical specifications for dimensions and mounting options.
5.1 Njikọ njikọ
- Ntinye (AC): Connect the AC input wires (Blue for Neutral, Brown for Line) to your main power source. Ensure the input voltage nọ n'ime oke 180-295VAC akọwapụtara.
- Mpụta (DC): Connect the DC output wires (Black for -V, Red for +V) to your LED lighting fixture. Observe correct polarity.
- Nda ala: Ensure the power supply is properly grounded to prevent electrical hazards.
5.2 Na-arịgo
- Mount the power supply in a location that allows for adequate air circulation to facilitate cooling by free air convection.
- The unit is IP67/IP65 rated, making it suitable for indoor or outdoor installations, including dry, damp, ma ọ bụ ebe mmiri.
- Refer to the mechanical drawings in Section 11 for mounting hole dimensions and overall unit size.
For detailed installation instructions, please refer to the official MEAN WELL installation manual available on their websaịtị: meanwell.com/webnet/search/InstallationSearch.html
Image 5.1: Mechanical specifications for B-Type/DA-Type models and a reference to the online installation manual.
6. Ntuziaka ọrụ
6.1 Basic Arụmọrụ
Once properly installed and connected, the ELG-75-C700 will provide a constant current output to the connected LED load. Ensure the LED load's voltage requirements fall within the power supply's constant current region (53~107V for C700 model).
6.2 Output Current Adjustment (A-Type)
For A-Type models, the constant current level can be adjusted via an internal potentiometer. This allows fine-tuning of the output current within the specified adjustment range (350~700mA for C700 A-Type).
6.3 Dimming Operation (B-Type)
B-Type models feature a 3-in-1 dimming function, allowing adjustment of the output current via 0~10VDC, PWM signal, or resistance. The dimming wires are typically DIM+ (Blue) and DIM- (White).
- 0~10VDC Dimming: Connect a 0~10VDC dimmer to the DIM+ and DIM- terminals. 0V typically corresponds to 0% output, and 10V to 100% output.
- PWM Signal Dimming: Connect a PWM signal source to the DIM+ and DIM- terminals. The frequency range for PWM dimming is typically 100Hz ~ 3KHz.
- Resistance Dimming: Connect a variable resistor (potentiometer) between DIM+ and DIM-. The resistance value will determine the output current level.
Caution: Do not connect "DIM-" to "-V" (output negative terminal).
Image 6.1: Diagram illustrating the dimming operation for B-Type models, showing connections for 0-10VDC, PWM, and resistance dimming, along with corresponding characteristic curves.
7. Njirimara arụmọrụ
7.1 Block Diagram, Derating Curve, and Static Characteristics
The internal block diagram illustrates the functional stages of the power supply, including EMI filter, PFC circuit, power switching, rectifiers & filter, and protection circuits (O.T.P., O.L.P., O.V.P.). The derating curve indicates the maximum permissible output load as a function of the case temperature (Tcase). The static characteristics graph shows the relationship between output load and input voltage, demonstrating stable output performance across the input voltage oke.
Image 7.1: This image displays the functional block diagram of the ELG-75-C series, the derating curve showing load percentage versus case temperature, and the static characteristics graph illustrating load percentage versus input voltage.
7.2 Power Factor, Efficiency, and Driving Methods
The power factor characteristic graph illustrates the power factor (PF) at different load levels for various input voltages (277V and 230V), highlighting the built-in active PFC function. The efficiency vs. load graph demonstrates the power supply's efficiency at different load percentages, showing that the ELG-75-C series achieves high efficiency, up to 93%. The ELG-75-C series is designed to operate in constant current mode (CC) to drive LED modules, as shown by the typical LED power supply I-V curve which includes the constant current area and hiccup protection.
Image 7.2: This image presents graphs for the power factor characteristic, efficiency versus load, and the typical I-V curve for driving LED modules.
8. Nlekọta
The ELG-75-C700 LED power supply is designed for reliable operation with minimal maintenance. Follow these guidelines:
- Nhicha: Periodically inspect the unit for dust or debris accumulation, especially around cooling surfaces. Clean with a soft, dry cloth if necessary. Ensure power is disconnected before cleaning.
- Nyocha: Regularly check wiring connections for any signs of damage, corrosion, or loose terminals.
- gburugburu: Hụ na gburugburu ebe ọrụ ahụ dị n'ime oke okpomọkụ na iru mmiri akọwapụtara iji gbochie ọdịda ngwa ngwa.
- No User-Serviceable Parts: Do not attempt to open or repair the power supply. Doing so will void the warranty and may expose you to hazardous voltages.
9. Nchọpụta nsogbu
If you encounter issues with your ELG-75-C700 power supply, consider the following common troubleshooting steps:
- Enweghị ike mmepụta:
- Verify that the AC input power is connected and within the specified voltage nso (180-295VAC).
- Check for tripped circuit breakers or blown fuses in the input line.
- Gbaa mbọ hụ na njikọ wiwi niile echekwabara na zie ezi.
- The unit may be in protection mode (e.g., short circuit, over voltage, over temperature). Disconnect power, wait a few minutes, and reapply.
- LEDs Flickering or Dim:
- Check the LED load for proper connection and ensure it is compatible with the power supply's constant current output.
- If using a dimming function (B-Type), verify the dimmer is correctly connected and functioning. Ensure DIM- is not connected to -V.
- Confirm the ambient temperature is within the operating range to avoid thermal derating.
- ekpo oke ọkụ:
- Ensure adequate ventilation around the power supply. Do not obstruct airflow.
- Verify the load is not exceeding the rated power of the unit.
- Check the ambient temperature.
If the problem persists after performing these checks, contact qualified service personnel or MEAN WELL technical support.
10. Ozi nchekwa
WARNING: Risk of electric shock. Installation and servicing should only be performed by qualified personnel.
- Always disconnect power before installation, maintenance, or troubleshooting.
- Gbaa mbọ hụ na ntọala nke unit ahụ kwesịrị ekwesị.
- Do not operate the power supply beyond its specified ratings (voltage, ugbu a, okpomọkụ).
- Do not expose the unit to excessive moisture or extreme temperatures outside its operating range.
- Gbaa mbọ hụ na wiwi niile dabara na koodu eletriki mpaghara na nke mba.
- This device is a Type HL LED Driver for use in Class I, Division 2 hazardous location luminaires. Adhere to all relevant safety standards for such environments.
11. Nkọwa maka igwe
The following diagrams provide the mechanical dimensions and outlines for different types of the ELG-75-C series power supplies. All dimensions are in millimeters (mm).
11.1 Blank-Type / D-Type and A-Type
Image 11.1: Mechanical drawings for Blank-Type, D-Type, and A-Type ELG-75-C series models, showing dimensions, case temperature measurement point, and the location of the internal potentiometer for A-Type.
11.2 B-Type / DA-Type
Image 11.2: Mechanical drawing for B-Type and DA-Type ELG-75-C series models, showing dimensions and dimming wire connections.
12. Akwụkwọ ikike na nkwado
The MEAN WELL ELG-75-C700 LED Power Supply comes with a 5-afọ akwụkwọ ikike site na ụbọchị ịzụrụ. Akwụkwọ ikike a na-ekpuchi ntụpọ dị na ngwa na arụ ọrụ n'okpuru ojiji nkịtị.
For warranty claims, technical support, or further assistance, please contact your authorized MEAN WELL distributor or visit the official MEAN WELL websaịtị maka ozi kọntaktị.
Ndị ọchịchị Websaịtị: www.meanwell.com
