SEBSON Motion Detector and Chime Instruction Manual

1. Okwu mmalite

This manual provides essential information for the proper installation, operation, and maintenance of your SEBSON Motion Detector and Chime. Please read these instructions carefully before using the device to ensure safe and efficient performance. This device is designed to detect movement and provide an audible alert, functioning as both a motion alarm and a passage chime.

2. Ozi nchekwa

• Ensure the device is installed in a dry environment, as it has an IP20 protection rating, meaning it is not protected against water.
• Ewepụla ngwaọrụ ahụ na oke okpomọkụ ma ọ bụ ìhè anyanwụ kpọmkwem.
• Debe ebe ụmụaka na-apụghị iru.
• Only use the specified 9V E-Block battery type.
• Tụfuo batrị n'ụzọ ziri ezi dịka iwu obodo siri dị.

3. Ihe ngwugwu

• 1 x SEBSON Motion Detector and Chime (Model BWM_ALARM_B)
• Arịọnụ mgbodo
• Akụrụngwa mgbanye (skru, plọg mgbidi)
• Note: 1x 9V E-Block battery is required and not included.

4. Ngwaahịa gafereview

The SEBSON Motion Detector and Chime is a compact, battery-powered device designed for versatile use. It features a passive infrared (PIR) sensor to detect movement and offers two distinct audible alert modes: a chime for passage detection and an alarm for security purposes.

Foto 1: N'ihu view of the SEBSON Motion Detector and Chime.

Foto 2: N'ihu view of the device, highlighting the SEBSON brand logo.

Ọgụgụ 3: N'azụ view of the motion detector, illustrating the integrated mounting bracket.

5. Nhazi

5.1 Ntinye batrị

1. Gently slide open the battery compartment cover located on the back of the device.
2. Insert one 9V E-Block battery, ensuring correct polarity (+/-).
3. Mechie mkpuchi nke batrị batrị nke ọma.

5.2 Ịtinye ngwaọrụ

The device can be mounted on a wall using the provided bracket and hardware.

1. Choose a suitable location for installation. Consider the desired detection area and ensure the sensor has an unobstructed view.
2. Detach the mounting bracket from the main unit if it is not already separate.
3. Mark the positions for drilling holes on the wall using the bracket as a template.
4. Gwuo oghere ma tinye mgbidi mgbidi.
5. Chekwaa ihe nkwado mgbago na mgbidi site na iji skru ndị enyere.
6. Attach the motion detector unit to the mounted bracket. The sensor housing can pivot 360 degrees within the bracket to adjust the detection angle.

Figure 4: Illustration of battery insertion and how the device attaches to the wall-mounted bracket.

6. Ntuziaka ọrụ

6.1 Nhọrọ ọnọdụ

The device features a three-position switch for selecting the operating mode:

• CHIME: In this mode, the device emits a short chime sound when motion is detected. This is suitable for use as a passage detector in shops or offices.
• Gbanyụọ: The device is turned off and will not detect motion or emit any sound.
• ỌRAR: In this mode, the device emits a loud alarm sound (approximately 70dB) when motion is detected. This is suitable for security purposes.

Ọgụgụ 5: Zuru ezu view of the mode selection switch (1: Chime, 2: Off, 3: Alarm).

6.2 Mpaghara nchọpụta

The motion detector has a detection range of up to 8 meters and a detection angle of 60 degrees. For optimal performance, position the device to cover the desired area without obstructions.

Figure 6: Diagram showing the detection range (8m) and angle (60°), along with the 360° rotational capability of the sensor head.

7. Nlekọta

7.1 nnọchi batrị

When the sound becomes weak or the device stops responding, it is time to replace the 9V E-Block battery. Follow the battery installation steps in Section 5.1.

7.2 Nhicha

To clean the device, use a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the surface or internal components. Ensure no moisture enters the device.

8. Nchọpụta nsogbu

• Device not detecting motion:
  • Check if the battery is correctly installed and has sufficient power. Replace if necessary.
  • Ensure the device is not in the "OFF" position.
  • Verify that the detection area is clear of obstructions.
  • Adjust the angle of the sensor to cover the desired area.
• No sound or weak sound:
  • Dochie batrị 9V.
  • Ensure the device is not in the "OFF" position.
• Mkpu ụgha:
  • Reposition the device to avoid areas with rapid temperature changes (e.g., near heaters, air conditioners) or moving objects (e.g., curtains near a window).
  • Ensure the detection area is free from small animals if not intended to detect them.

9. Nkọwapụta

10. Akwụkwọ ikike na nkwado

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official SEBSON websaịtị. Debe ihe akaebe nke ịzụrụ ihe maka akwụkwọ ikike ọ bụla.