Stihl MS 201 TC-M Chainsaw Instruction Manual

1. Ozi nchekwa

Operating a chainsaw can be dangerous if proper safety precautions are not followed. Always read and understand the entire instruction manual before operating the Stihl MS 201 TC-M chainsaw. Failure to follow safety instructions can result in serious injury or death.

Ngwa nchekwa nkeonwe (PPE)

• Nchedo isi: Wear a safety helmet with face and hearing protection.
• Nchedo anya: Na-eyi ugogbe anya nchekwa ma ọ bụ enyo nchekwa mgbe niile.
• Nchekwa aka: Jiri uwe aka ọrụ siri ike.
• Nchedo Ụkwụ: Wear chainsaw protective trousers or chaps.
• Nchekwa ụkwụ: Wear safety boots with steel toes and non-slip soles.

Fuel Handling Safety

• Always mix and handle fuel in a well-ventilated area, away from ignition sources.
• Jiri naanị akpa mmanụ ọkụ akwadoro.
• Smokeụ sịga mgbe ị na-agba mmanụ.
• Hichapụ mmanụ ọkụ ọ bụla wụfuru ozugbo.

2. Ngwaahịa gafereview

The Stihl MS 201 TC-M is a powerful and compact gasoline-powered chainsaw designed for professional tree care and pruning. It features a 35 cm cutting length and is equipped with advanced engine technology for efficient operation.

Figure 2.1: Top-side view of the Stihl MS 201 TC-M chainsaw, highlighting the ergonomic handle and engine housing.

Foto 2.2: Akụkụ view of the Stihl MS 201 TC-M chainsaw, showing the Stihl branding and engine components.

3. Nhazi

Iwepu na Mgbakọ

1. Jiri nlezianya wepụ ihe niile dị na nkwakọ ngwaahịa.
2. Inspect for any shipping damage. If damaged, do not use and contact your dealer.
3. Ensure all parts listed in the packing list are present.

Bar and Chain Installation

Proper installation of the guide bar and saw chain is crucial for safe and efficient operation.

1. Ensure the chain brake is disengaged.
2. Remove the chain sprocket cover by loosening the nuts.
3. Debe ogwe nduzi n'elu studs.
4. Fit the saw chain around the sprocket and into the guide bar groove. Ensure the cutting edges face forward on the top of the bar.
5. Replace the chain sprocket cover and hand-tighten the nuts. Do not fully tighten yet.
6. Adjust chain tension (refer to 'Chain Tension Adjustment' in Section 5).
7. Fully tighten the chain sprocket cover nuts.

Ọgụgụ 3.1: nso nso view of the chainsaw's chain and guide bar, illustrating proper assembly.

Fuel and Chain Oil Filling

The MS 201 TC-M operates on a gasoline-oil mixture and requires chain lubricant.

• Mmanụ ụgbọala: Use a high-quality unleaded gasoline mixed with Stihl 2-stroke engine oil at the recommended ratio (typically 50:1). Refer to the fuel tank cap for specific ratios.
• Mmanụ Chain: Fill the chain oil tank with high-quality bar and chain lubricant. Do not use waste oil.

Ensure both caps are securely tightened after filling.

4. Ntuziaka ọrụ

Malite na Chainsaw

1. Debe chainsaw n'elu ebe siri ike ma dị larịị.
2. Tinye breeki yinye site n'ịkwanye onye nche aka n'ihu n'ihu.
3. Set the master control lever to the cold start position (choke).
4. Jide aka gị n'aka n'ihu nke ọma ma tinye ụkwụ gị n'aka azụ.
5. Pull the starter cord slowly until resistance is felt, then pull briskly until the engine fires briefly.
6. Bugharịa ihe njikwa ukwu gaa n'ọnọdụ ọkara nke throttle.
7. Pull the starter cord again until the engine starts.
8. Blip the throttle to disengage the half-throttle and return to idle.
9. Disengage the chain brake before beginning cutting operations.

Stopping the Chainsaw

To stop the engine, move the master control lever to the STOP position.

Ịrụ ọrụ breeki Chain

The chain brake is a critical safety feature. It can be engaged manually by pushing the front hand guard forward or automatically by inertia during kickback. Always ensure the chain brake is functional before each use.

5. Nlekọta

Regular maintenance ensures the longevity and safe operation of your Stihl MS 201 TC-M chainsaw.

Ndozi nhịahụ nke Chain

Correct chain tension is vital. A loose chain can derail, and an overly tight chain can cause premature wear to the bar and chain, and reduce engine power.

1. Loosen the nuts on the chain sprocket cover.
2. Using the tensioning screw, adjust the chain until it fits snugly against the underside of the guide bar, but can still be pulled around by hand.
3. Lift the tip of the guide bar slightly while tightening the nuts on the chain sprocket cover.
4. Check tension again.

Ịcha Chain

A sharp chain is essential for efficient and safe cutting. Sharpen the chain regularly or have it professionally sharpened.

Nchacha ikuku ikuku

Clean the air filter regularly to maintain engine performance and prevent damage. Remove the filter cover and clean the filter element with warm soapy water or compressed air. Replace if damaged.

Nyochaa Spark Plug

Inspect the spark plug for wear and proper gap. Replace if electrodes are worn or fouled. Refer to the specifications for the correct spark plug type and gap.

Ntuziaka Bar mmezi

Regularly clean the guide bar groove and oil holes. Flip the guide bar periodically to ensure even wear.

6. Nchọpụta nsogbu

This section addresses common issues you might encounter with your Stihl MS 201 TC-M chainsaw.

7. Nkọwapụta

Key technical specifications for the Stihl MS 201 TC-M chainsaw:

• Nọmba nlereanya: MS201
• Isi mmalite ike: mmanụ ụgbọala
• Ogologo igbupu: 35 cm
• Ibu ihe: 3.85 n'arọ (8.49 lbs)
• Akụkụ ngwaahịa: 37 x 10 x 37 cm (14.57 x 3.94 x 14.57 inch)
• Ihe: Plastic (ụlọ)
• Onye nrụpụta: STIHL
• GTIN (UPC): 00795711953546

8. Akwụkwọ ikike na nkwado

For warranty information, please refer to the warranty card included with your product or contact your authorized Stihl dealer. Keep your proof of purchase for warranty claims.

For technical support, spare parts, or service, please contact your local authorized Stihl service center. Only use genuine Stihl replacement parts and accessories.