1. Okwu mmalite
This manual provides essential information for the safe and correct installation, operation, and maintenance of the Legrand 191510 Plexo Recessed Switch. Please read these instructions thoroughly before beginning any work.
1.1 Ozi nchekwa
- A ga-arụrịrị nrụnye site n'aka onye ọrụ ọkụ eletrik ruru eru dịka koodu eletriki mpaghara na nke obodo siri dị.
- Always disconnect power at the main circuit breaker before installing or servicing the switch.
- Do not use the switch if it appears damaged.
- Gbaa mbọ hụ na ntọ ala kwesịrị ekwesị ebe achọrọ ya.
- The switch is designed for recessed installation and offers waterproof protection (IP54).
1.2 Ngwaahịa gafereview
The Legrand 191510 Plexo Recessed Switch is a grey, waterproof switch designed for environments requiring protection against dust and water, such as outdoor areas, basements, and garages. It features a robust design for recessed installation and includes a box with upper and lower membranes for pipe inlet up to 25 mm, facilitating a secure and sealed cable entry.
Foto 1: N'ihu view of the Legrand 191510 Plexo Recessed Switch.
2. Ntuziaka nwụnye
2.1 Ngwa achọrọ
- Screwdriver (Phillips na flathead)
- Waya waya
- Voltagọ bụ onye nyocha
- Drill (if creating a new recess)
- Ihe teepu
2.2 Mounting the Switch Box
- Hụ na ewepụla ike ọkụ eletrik na ihe mgbawa sekit bụ isi.
- Prepare the recess in the wall according to the switch dimensions (approximately 8 x 8 x 5.5 cm).
- Identify the desired cable entry point(s) on the switch box (upper or lower membrane). Carefully pierce the membrane to allow cable passage.
- Insert the electrical cables through the prepared membrane(s).
- Secure the switch box into the recess using appropriate fasteners. The joint joints between the mechanism and the wall facilitate adjustment on various surfaces.
Ọgụgụ 2: N'azụ view of the switch box with cable entry membranes and mounting points.
2.3 Ịkpọnye Mgbanwe ahụ
- Strip approximately 13mm of insulation from the ends of the electrical wires.
- Connect the wires to the appropriate terminals on the switch mechanism. Refer to the wiring diagram usually found on the product or packaging. For a 1-way circuit, connect the live input to one terminal and the switched live output to the other.
- Gbaa mbọ hụ na njikọ niile siri ike na nchekwa.
Ọgụgụ 3: Zuru ezu view of the wiring terminals.
2.4 Assembling the Switch Mechanism and Cover
- Carefully position the wired switch mechanism into the mounted switch box.
- Ensure the mechanism is seated correctly and securely within the box.
Figure 4: Internal mechanism of the switch.
- Attach the grey front plate to the switch mechanism, ensuring it clicks into place and forms a tight seal for waterproof protection.
Figure 5: Attaching the front plate to the switch mechanism.
- Once fully assembled, restore power at the main circuit breaker.
3. Ọrụ
3.1 Ọrụ bụ isi
The Legrand 191510 Plexo Recessed Switch operates as an ON-ON-OFF push-button switch. Pressing the button will toggle the connected electrical circuit between its ON and OFF states. The switch has 3 positions, allowing for flexible control of the connected load.
4. Nlekọta
4.1 Nhicha
To clean the switch, wipe the surface with a soft, damp cloth. Do not use abrasive cleaners, solvents, or excessive water, as this may damage the finish or compromise the waterproof seal.
4.2 Nyocha
Periodically inspect the switch for any signs of damage, wear, or compromise to the waterproof seal. If any damage is observed, disconnect power and have the switch inspected or replaced by a qualified professional.
5. Nchọpụta nsogbu
5.1 Okwu nkịtị
- Mgbanwe anaghị aza: Check if the main circuit breaker is ON. Verify all wiring connections are secure. If the issue persists, consult a qualified electrician.
- Ọrụ na-adịte aka: This could indicate a loose connection or internal damage. Disconnect power and have the switch inspected by a professional.
- Ntinye mmiri: If water is observed inside the switch or connected enclosure, immediately disconnect power. The waterproof seal may be compromised. The switch must be replaced.
6. Nka na ụzụ nkọwa
| Nkọwapụta | Uru |
|---|---|
| Nọmba nlereanya | 191510 |
| Ụdị | Legrand |
| Ụdị ọrụ | Gbanyụọ-Ngbanyụ |
| Ogo dị ugbu a | 6 Amps |
| Nrụ ọrụ Voltage | 230 volts |
| Ụdị kọntaktị | Na-emepe emepe |
| Ụdị njikọ | Tinye |
| Ụdị njedebe | Bọtịnụ |
| Akụkụ (L x W x H) | 3.35 x 3.35 x 1.57 sentimita (8.5 x 8.5 x 4 cm) |
| Circuit .dị | 1-ụzọ |
| Ụdị Actuator | Ihe mgbakwasị ụkwụ |
| Ngwa kọntaktị | Ọla |
| Ogo nchekwa mba ụwa | IP54 |
| Ọnụọgụ nke ọkwa | 3 |
| Ụdị njikwa | Pịa bọtịnụ |
| Usoro njikwa | Metụ aka |
| Protocol Njikọta | X-10 |
| Agba | Agba ntụ |
| Wattage | 1380 watt |
| Ibu Ibu | 3.52 ounces (100g) |
7. Akwụkwọ ikike Ozi
The Legrand 191510 Plexo Recessed Switch is covered by a standard manufacturer's warranty. For specific details regarding warranty terms, duration, and claims, please refer to the documentation provided with your purchase or visit the official Legrand websaịtị. Debe ihe akaebe nke ịzụrụ ihe maka ebumnuche ikike.
8. Nkwado ndị ahịa
For further assistance, technical support, or inquiries regarding the Legrand 191510 Plexo Recessed Switch, please contact Legrand customer service. You can find contact information, FAQs, and additional resources on the official Legrand websaịtị:
