1. Okwu mmalite
Thank you for choosing the Einhell TC-LD 25 Laser Distance Meter. This device is designed for quick and accurate measurement of distances up to 25 meters. Its compact design and user-friendly interface make it an ideal tool for various applications in construction, renovation, and DIY projects. Please read this manual carefully before using the device to ensure safe and optimal operation.
Figure 1: Einhell TC-LD 25 Laser Distance Meter
2. Ozi nchekwa
This device uses a Class II laser. Observe the following safety precautions:
- Elepụla anya ozugbo n'ime oghere laser.
- Atụla ọkụ laser aka na mmadụ ma ọ bụ anụmanụ.
- Zere ikpughe anya ozugbo na doo laser.
- Do not disassemble or modify the device. Repairs should only be performed by authorized personnel.
- Debe ngwaọrụ ahụ ka ụmụaka ghara iru ya.
The laser diode operates at 635 nm.
3. Ngwaahịa gafereview
Familiarize yourself with the components of your Einhell TC-LD 25.
Foto 2: N'ihu View (Display, Buttons)
Ọgụgụ 3: Azụ View (Battery Compartment)
Foto 4: Akụkụ View
Ngwa:
- Laser Aperture: Emits the laser beam for measurement.
- Ngosipụta ihuenyo: Shows measurement results, mode, and battery status.
- Measurement Button (ON/MEAS): Powers on the device and initiates measurements.
- Function/Unit Button (FUNC/UNIT): Cycles through measurement modes and changes units.
- Reference Point Button: Switches between front and rear reference points.
- Clear/Off Button (C/OFF): Clears the last measurement or powers off the device.
- Akụkụ batrị: Located at the back for AAA batteries.
4. Nhazi
4.1 Ntinye batrị
The Einhell TC-LD 25 requires two (2) AAA alkaline batteries (not included).
- Open the battery compartment cover located on the back of the device (refer to Figure 3).
- Fanye batrị AAA abụọ, na-ahụ polarity ziri ezi (+/-).
- Mechie mkpuchi nke batrị batrị nke ọma.
Ọgụgụ 5: Ụlọ batrị
5. Ntuziaka ọrụ
5.1 Gbanyụọ / gbanyụọ
- Ka ịgbanwuo: Pịa ON/MEAS button. The laser will activate.
- Ịgbanyụ: Pịa ma jide C/ Gbanyụọ button for a few seconds. The device also features an automatic shutdown function after 3 minutes of inactivity to conserve battery life.
5.2 Nha Anya Dị Mfe
- Gbanwuo ngwaọrụ.
- Point the laser beam at the target.
- Pịa ON/MEAS button once. The measured distance will be displayed on the screen.
5.3 Ntụle Na-aga n'ihu (Oke/Max)
This mode allows you to track the minimum and maximum distances as you move the device.
- Pịa FUNC/UNIT button until the continuous measurement icon (often a running person or min/max symbols) appears on the display.
- Move the device slowly towards or away from the target. The display will continuously update the current, minimum, and maximum distances.
- Pịa ON/MEAS to stop continuous measurement and view the final minimum and maximum values.
Figure 6: Continuous Measurement Example
5.4 Changing Reference Point
The device can measure from its front edge or its rear edge. The default is usually the rear edge.
- Pịa Ebe ntụaka button to toggle between front and rear measurement. An icon on the display will indicate the active reference point.
Figure 7: Measuring from Rear Edge
Figure 8: Measuring from Front Edge
5.5 nkeji na-agbanwe
The device primarily uses metric units (meters).
- Pịa FUNC/UNIT button repeatedly to cycle through available units (e.g., m, ft, in).
6. Nlekọta
- Jiri nwayọ hichaa ngwaọrụ ahụ, damp akwa . Ejila ihe nchacha abrasive ma ọ bụ ihe mgbaze.
- Regularly check the battery compartment for corrosion. Remove batteries if the device will not be used for an extended period.
- Store the device in its included pouch in a dry, dust-free environment.
Figure 9: Included Carrying Pouch
7. Nchọpụta nsogbu
| Nsogbu | Ihe nwere ike ime | Ngwọta |
|---|---|---|
| Ngwaọrụ anaghị agbanwu | Low or dead batteries; incorrect battery polarity | Replace batteries; check polarity |
| Ntụle ezighi ezi | Unstable surface; obstruction in laser path; extreme temperatures | Ensure stable measurement; clear path; operate within specified temperature range |
| Laser anaghị ahụ anya | Bright ambient light; long distance measurement | Use in lower light conditions; use a target plate for long distances |
8. Nkọwapụta
| Njirimara | Nkọwapụta |
|---|---|
| Nọmba nlereanya | TC-LD 25 (2270075) |
| Oke nso | 0.05 m - 25 m |
| Izizi nha nha | +/- 3 mm / m |
| Klas laser | Klas II |
| Azụ Laser | 635 nm |
| Gbanyụọ akpaghị aka | 3 nkeji |
| Batrị | 2 x AAA (Alkaline) |
| Akụkụ (L x W x H) | 11.2 x 2.5 x 4 cm |
| Ibu | 70 g |
| Ihe onwunwe | Acrylonitrile Butadiene Styrene |
| Ogo nchekwa mba ụwa | IP54 (Water resistant) |
9. Akwụkwọ ikike na nkwado
Einhell products are manufactured with high-quality materials and undergo strict quality control. For any warranty claims or technical support, please refer to your purchase documentation or contact Einhell customer service.
Spare parts availability in the EU is guaranteed for 1 year.
For further information, visit the official Einhell store: Einhell Store
