LEVOIT Kyra Himalayan Salt Lamp

Okwu mmalite

The LEVOIT Kyra Himalayan Salt Lamp is crafted from natural Himalayan salt crystals, designed to provide a warm, ambient glow. This manual provides essential information for the safe and effective use of your salt lamp.

Ihe ngwugwu

• 1 x LEVOIT Kyra Himalayan Salt Lamp Crystal Rock
• 1 x 6.5 Ft UL-Listed Power Cord with Touch Brightness Dimmer Switch
• 3 x C7 15 Watt Incandescent Light Bulbs (one pre-installed, two extra)
• 1 x Akwụkwọ ntuziaka onye ọrụ

Ntuziaka nchekwa

• Nchekwa Eletriki: Ensure the power input is 120V/60Hz. Use only the provided UL-listed power cord and bulbs. Do not use the lamp with damaged cords or plugs.
• Ịdọ aka ná ntị mmiri mmiri: Himalayan salt is hygroscopic, meaning it absorbs moisture from the air. Place the lamp in a dry environment. If the lamp becomes moist, turn it on to a high setting to allow the heat from the bulb to dry the crystal.
• Nkwanye: Debe lamp on a stable, water-resistant surface to protect furniture from potential moisture build-up.
• Ijikwa: Handle the salt crystal with care as it can be fragile.
• Ụmụaka na anụ ụlọ: Debe lamp out of reach of children and pets to prevent accidental damage or ingestion of salt.

Melite

1. Carefully remove the salt lamp and all components from the packaging.
2. Place the salt crystal securely onto the stainless steel base.
3. Ensure the pre-installed C7 15W bulb is properly seated in the E12 socket.
4. Debe lamp n'elu larịị, kwụsiri ike.
5. Plug the ETL certified power cord into a standard 120V/60Hz electrical outlet.

Image: The LEVOIT Kyra Himalayan Salt Lamp with its natural crystal rock and stainless steel base, ready for setup.

Ntuziaka ọrụ

The LEVOIT Kyra Himalayan Salt Lamp features a touch dimmer switch for easy control of brightness.

1. Agbanye/ Gbanyụọ: Lightly tap the touch dimmer switch once to turn the lamp gbanye ma ọ bụ gbanyụọ.
2. Na-edozi ihie: Mgbe lamp is on, press and hold the touch dimmer switch. The brightness will gradually increase or decrease. Release the switch when the desired brightness level is reached.

Image: A hand operating the touch dimmer switch on the lamp's power cord, illustrating how to adjust brightness.

Nlekọta

Nhicha

Regularly dust the salt crystal with a dry, clean cloth. If the crystal becomes moist, turn the lamp on to a high setting for several hours to dry it out.

Mgbanwe Bulb

If the bulb needs replacement, use only C7 15W incandescent light bulbs with an E12 socket. Two extra bulbs are included in your package.

1. Kpupu lamp site na ntinye ike.
2. Carefully flip the lamp gafere.
3. Remove the four screws from the base using a small screwdriver.
4. Gently slide off the base while holding the salt crystal.
5. Carefully set the salt crystal aside.
6. Remove the old bulb from its socket.
7. Install the new C7 15W bulb into the socket.
8. Align the base back onto the salt crystal, ensuring the screw holes are aligned.
9. Replace and tighten all four screws.

Nchọpụta nsogbu

• Lamp anaghị agbanye: Check if the power cord is securely plugged into the outlet and the lamp. Ensure the bulb is properly seated and not burnt out. Try a different outlet.
• Lamp is dim or flickers: The bulb may be loose or nearing the end of its life. Replace the bulb if necessary.
• Lamp is sweating/moist: This is normal for salt lamps in humid environments. Turn the lamp to a high brightness setting and leave it on for several hours to dry the crystal. Ensure the lamp is placed in a dry area.
• Touch dimmer is unresponsive: Ensure your hands are clean and dry when operating the touch switch. If the issue persists, unplug the lamp for a few minutes and then plug it back in.

Nkọwapụta

Akwụkwọ ikike na nkwado

For warranty information or product support, please refer to the warranty card included in your package or contact LEVOIT customer service directly. Keep your purchase receipt for warranty claims.