GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Okwu mmalite

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Ozi nchekwa

Ịdọ aka ná ntị: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Hụ na agbanyụrụ ọkụ eletrik na ihe mgbawa sekit tupu etinye ya.
• Ezubere ngwaọrụ a maka nrụnye dịka koodu eletrik nke mba na ụkpụrụ mpaghara si dị.
• Do not use in wet locations or where directly exposed to water.
• Maka naanị ime ụlọ.

Ihe ngwugwu

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Nwụnye kposara
• Wire Nuts (may vary by package)
• Akwụkwọ ntuziaka (akwụkwọ a)

Ntọala na nwụnye

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Turn OFF Power: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Wepu Mgbanwe Ochie: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Chọpụta waya:
   • Line (Hot): Usually black, coming from the circuit breaker.
   • Ibu: Usually black, going to the light fixture or appliance.
   • Anọpụ iche: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Ala: Usually green or bare copper.
4. Jikọọ Switch ọhụrụ: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Jikọọ Ahịrị wire to the terminal marked "LINE".
   • Jikọọ Ibu ibu wire to the terminal marked "LOAD".
   • Jikọọ Anọpụ iche wire to the terminal marked "NEUTRAL".
   • Jikọọ Ala wire to the terminal marked "GROUND".

   Hụ na njikọ niile dị nchebe. Ọ bụrụ na obi adịghị gị mma maka waya, gakwuru ọkachamara ọkụ eletrik ruru eru.

5. Mgbanwe Ugwu: Carefully push the wired switch into the wall box. Secure it with the provided screws.
6. Wụnye Plate Wall: Attach the new or existing wall plate.
7. Weghachi ike: Gbanye ike ahụ ọzọ na ihe mgbawa sekit ahụ.

Foto 1: N'ihu view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave Inclusion (Pairing)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle otu ugboro. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Na-arụ ọrụ Switch

Njikwa akwụkwọ ntuziaka

• Pịa n'elu of the paddle to turn the connected load ON.
• Pịa ala of the paddle to turn the connected load Gbanyụọ.

Njikwa Z-Wave

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Nlekọta

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Nhicha: To clean the switch, wipe it with a soft, damp akwa . Ejila ihe nchacha abrasive ma ọ bụ ihe mgbaze.
• Mmelite femụwe: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• General Nlekọta: Hụ na ihe mgbanwe ahụ anaghị ekpughe oke mmiri ma ọ bụ oke okpomọkụ.

Nchọpụta nsogbu

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle otu ugboro. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Nkọwapụta

Akwụkwọ ikike na nkwado

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl websaịtị ma ọ bụ kpọtụrụ ngalaba ọrụ ndị ahịa ha.

Websaịtị: www.gocontrol.com

Onye nrụpụta: GOCONTROL