TECKNET WA838 Wireless Doorbell Kit Instruction Manual

Okwu mmalite

Thank you for choosing the TECKNET WA838 Wireless Doorbell Kit. This kit provides a reliable and convenient solution for your home or office, ensuring you never miss a visitor. Featuring a waterproof push button transmitter and plug-in receivers, this system offers a wide operating range, multiple melodies, and adjustable volume levels. Please read this manual carefully before installation and use to ensure proper operation and longevity of your device.

Image: The TECKNET WA838 Wireless Doorbell Kit, showing one push button transmitter and two plug-in receivers.

Ihe ngwugwu

Biko lelee ngwungwu maka ihe ndị a:

• 1 x Wireless Push Button Transmitter
• 2 x Plug-in Chime Receivers
• 1 x teepu nrapado nwere akụkụ abụọ
• 2 x Screws and Wall Plugs (for optional mounting)
• Akwụkwọ ntuziaka onye ọrụ 1 x (akwụkwọ a)

Ntọala na nwụnye

Transmitter Installation (Push Button)

1. Prepare the Transmitter: The transmitter is pre-installed with a battery. Ensure the battery insulation tab (if present) is removed.
2. Họrọ ebe: Select a flat, vertical surface near your door where the transmitter will be easily accessible to visitors. Ensure the surface is clean and dry.
3. Nhọrọ nkwụnye:
   • Adhesive Tape (Recommended for easy installation): Peel off one side of the double-sided adhesive tape and stick it firmly to the back of the transmitter. Peel off the other side and press the transmitter firmly onto the chosen surface for at least 30 seconds.
   • Screws (Recommended for enhanced security): Mepee nnyefe casing (if applicable, usually by prying gently from the bottom). Mark the screw holes on the wall. Drill pilot holes, insert wall plugs, and then secure the transmitter base with screws. Close the casing.
4. Ọnụọgụ enweghị mmiri: The transmitter is rated IP33 waterproof, suitable for outdoor use. However, avoid direct exposure to heavy rain or prolonged submersion.

Receiver Installation (Chime Unit)

1. Họrọ ebe: Select a standard electrical outlet inside your home or office. Consider central locations for optimal sound distribution.
2. Tinye: Simply plug the chime receiver into the chosen electrical outlet. No batteries are required for the receiver.
3. Multiple Receivers: If you have multiple receivers, plug them into different outlets in areas where you want to hear the doorbell chime.

Ntuziaka ọrụ

Changing Melodies

• Pịa Bọtịnụ Nhọrọ Melody (often located on the side of the receiver) to cycle through the 52 available melodies.
• Stop pressing when you hear your desired melody. The receiver will remember your selection even after being unplugged.

Na-agbanwe olu

• Pịa Bọtịnụ njikwa olu (often located on the side of the receiver) to cycle through the 4 adjustable volume levels (ranging from 52dB to 85dB).
• Select the volume level that best suits your environment. The receiver will remember your selection.

Visual Alert (Flashing Light)

• When the push button is pressed, the transmitter will flash a blue LED light.
• Simultaneously, the receiver will also flash a blue LED light, providing a visual alert in addition to the audible chime. This feature is particularly useful for individuals with hearing impairments.

Pairing Additional Transmitters/Receivers (If applicable)

Your kit comes pre-paired. If you purchase additional TECKNET WA838 components or need to re-pair them:

1. Tinye ihe nnata.
2. Pịa ma jide Bọtịnụ njikwa olu on the receiver for approximately 5 seconds until you hear a "ding" sound and the LED indicator starts flashing. This indicates the receiver is in pairing mode.
3. Immediately press the push button on the transmitter. The receiver will chime, indicating successful pairing.
4. To pair multiple transmitters with one receiver, repeat steps 2 and 3 for each additional transmitter.
5. To pair one transmitter with multiple receivers, repeat steps 2 and 3 for each additional receiver.

Nlekọta

• Transmitter Battery Replacement: The transmitter uses a standard 12V 23A alkaline battery. When the LED indicator on the transmitter no longer lights up or the range decreases significantly, it's time to replace the battery.
  1. Carefully open the transmitter casing.
  2. Remove the old battery and insert a new 12V 23A battery, ensuring correct polarity (+/-).
  3. Mechie casing nke ọma.
• Nhicha: Jiri ákwà dị nro ma kpọọ nkụ hichaa ihe ndị dị n'ọnụ ụzọ. Ejila ihe nhicha ma ọ bụ ihe mgbaze.
• Ọnọdụ gburugburu: While the transmitter is waterproof, extreme temperatures or prolonged direct sunlight can affect battery life and performance.

Nchọpụta nsogbu

Nkọwapụta

• Ụdị: WA838
• Nrụ ọrụ Voltage (Onye nnata): AC 110-240V
• Battery (Transmitter): 12V 23A batrị alkaline
• Ugboro arụ ọrụ: Ugboro redio
• Oke arụ ọrụ: Up to 300 meters (900 feet) in open air
• Selectable Melodies: 52
• Ọkwa olu: Ọkwa ise (52dB ruo 85dB)
• Waterproof Rating (Transmitter): IP33
• Atụmatụ pụrụ iche: Flashing LED indicator, Memory function for melody and volume, 64,000 anti-interference codes
• Agba: Nwa

Akwụkwọ ikike na nkwado

TECKNET provides an 18-month warranty for this product, covering manufacturing defects from the date of purchase. This warranty does not cover damage caused by misuse, accidents, unauthorized modifications, or normal wear and tear.

For technical support, warranty claims, or any questions regarding your TECKNET WA838 Wireless Doorbell Kit, please contact TECKNET customer service. Contact information can typically be found on the product packaging or the official TECKNET websaịtị.

Biko dowe ihe akaebe nke ịzụrụ ihe maka ebumnuche ikike.