1. Okwu mmalite
This manual provides comprehensive instructions for the installation, operation, and maintenance of the FEIG ID ISC.PR100 Proximity Reader. Please read this manual thoroughly before using the device to ensure proper functionality and safety.
The FEIG ID ISC.PR100 is a high-performance proximity reader designed for various applications requiring reliable RFID tag detection. It operates at 13.56MHz and offers a significant reading range.
2. Ozi nchekwa
Na-edebe nchekwa nchekwa ndị a mgbe niile iji gbochie mmerụ ahụ ma ọ bụ mebie ngwaọrụ:
- Ensure the power supply matches the device's specifications (12-24VDC).
- Ewepụla ngwaọrụ ahụ na oke okpomọkụ, iru mmiri, ma ọ bụ ìhè anyanwụ kpọmkwem.
- Zere idobe ma ọ bụ idobe ngwaọrụ ahụ na mmetụta siri ike.
- Anwala imeghe ma ọ bụ rụkwaa ngwaọrụ n'onwe gị. Kpọtụrụ ndị ọrụ ruru eru ọrụ niile.
- Gbanyụọ ike tupu ị rụọ ọrụ nrụnye ma ọ bụ mmezi ọ bụla.
3. Ngwaahịa gafereview
The FEIG ID ISC.PR100 Proximity Reader is a compact and robust device. Key features include:
- Ugboro arụ ọrụ: 13.56MHz
- Ntinye Voltagihe: 12-24VDC
- Maximum Signal Range: 180mm
- Interface: RS-232 / RS-485
- Supported Transponders: ISO-tags 15639
- Flash Memory: 64 kByte
- Klas nchekwa: IP 30
Figure 3.1: FEIG ID ISC.PR100 Proximity Reader. This image shows the compact grey rectangular device with a visible connector port on one end, indicating its robust design for industrial applications.
4. Ntọala na nwụnye
Follow these steps for proper installation of your ISC.PR100 Proximity Reader:
- Ịkwanye: Securely mount the reader in the desired location using appropriate fasteners. Ensure adequate ventilation and avoid mounting near strong electromagnetic interference sources.
- Njikọ ike: Connect the 12-24VDC power supply to the designated power input terminals. Observe correct polarity.
- Njikọ Njikọ Data: Connect the reader to your host system using either the RS-232 or RS-485 interface, as required by your application. Refer to the device's pinout diagram for correct wiring.
- Ntinye Antenna: Position the reader's antenna (if external) or the integrated antenna area to optimize read range and performance for your specific transponders.
- Ike izizi: Once all connections are secure, apply power to the device. The reader should perform a self-test and indicate readiness (e.g., via an LED indicator).
5. Ntuziaka ọrụ
The ISC.PR100 operates by detecting ISO-tags 15639 transponders within its read range. Operation is typically controlled by a host system via the connected interface (RS-232/RS-485).
5.1 Basic Arụmọrụ
- Ensure the reader is powered on and connected to the host system.
- Place an ISO-tag 15639 transponder within the reader's effective range (up to 180mm).
- The reader will detect the transponder and transmit its data to the host system according to the configured communication protocol.
5.2 Usoro nzikọrịta ozi
Detailed information regarding the communication protocol (commands, responses, data formats) for RS-232 and RS-485 interfaces can be found in the technical documentation provided by FEIG. It is essential to configure your host system to match the reader's communication settings (e.g., baud rate, parity, data bits, stop bits).
6. Nlekọta
The FEIG ID ISC.PR100 Proximity Reader is designed for low maintenance. However, regular care can extend its lifespan and ensure optimal performance.
- Nhicha: Use a soft, dry cloth to clean the exterior of the device. Do not use abrasive cleaners, solvents, or excessive moisture.
- Nyocha: Periodically inspect cables and connectors for any signs of wear or damage. Ensure all connections are secure.
- gburugburu: Maintain the operating environment within the specified temperature and humidity ranges to prevent damage.
7. Nchọpụta nsogbu
If you encounter issues with your ISC.PR100, refer to the following common problems and solutions:
| Nsogbu | Ihe nwere ike ime | Ngwọta |
|---|---|---|
| Ngwaọrụ anaghị agbanye ọkụ. | No power supply; incorrect voltage; faulty cable. | Check power connections and supply voltage. Ensure cables are not damaged. |
| Cannot read transponders. | Transponder out of range; incorrect transponder type; interference; faulty reader. | Ensure transponder is within 180mm range. Verify it's an ISO-tag 15639. Check for strong electromagnetic fields nearby. |
| Communication errors with host system. | Incorrect interface settings (baud rate, etc.); faulty data cable; software issue. | Verify communication settings match between reader and host. Check data cable integrity. Consult host system software documentation. |
If the problem persists after attempting these solutions, please contact FEIG technical support.
8. Nkọwapụta
| Oke | Uru |
|---|---|
| Nlereanya | ISC.PR100 |
| Nrụ ọrụ Voltage | 12-24VDC |
| Oriri ike | 5VA kacha |
| Ugboro arụ ọrụ | 13.56Mhz |
| Maximum Signal Range | 180mm |
| Interface | RS-232 / RS-485 |
| Ndị transponder akwadoro | ISO-tags 15639 |
| Ebe nchekwa Flash | 64 kByte |
| Klas nchekwa | IP30 |
| ASIN | B01E803L08 |
| Onye nrụpụta | FEIG |
| Ụbọchị mbụ dị | Eprel 1, 2016 |
9. Akwụkwọ ikike na nkwado
For warranty information and technical support, please refer to the official FEIG website or contact your authorized distributor. Keep your purchase receipt as proof of purchase for warranty claims.
FEIG is committed to providing high-quality products and excellent customer service. Should you require assistance beyond the scope of this manual, do not hesitate to reach out to their support channels.
